Electrolux 60830 Load Sensing Sensor Logic, Switching Off the Dishwasher, Emptying the Dishwasher

Page 33

Operating Instructions

Changing the programme after the start delay has been set: As long as the programme has not started, you can still change the start delay set by pressing a programme button.

0 1. Press the button for the new programme and hold it down.

First the indicator for the programme that has just been selected will flash.

After several seconds only the indicator for the new programme will be flashing.

2.Release the programme button.

The newly selected programme will start automatically following a countdown of the hours set.

Load Sensing – Sensor Logic

If a wash programme is started even though there are only a few dishes in the upper and/or lower basket, an intelligent electronic system adjusts the amount of water and the duration of the wash programme to the number of dishes. By this means it is possible to wash only a few dishes quickly and economically. At half load (6 place settings), up to 2 litres of water and 0.2 kWh of electricity are saved.

Switching Off the Dishwasher

Switch the dishwasher off when the multi-display indicates "0" for the remaining programme time.

0 1. Press the ON/OFF button. The ON/OFF button indicator extinguishes.

1

Hot steam may escape from the appliance when opening the door

 

immediately after the end of the programme.

2.Open the door carefully, as steam may escape.

 

Emptying the Dishwasher

3

• The dishes should be allowed to cool down before removing them

 

from the appliance, as hot dishes can be sensitive to knocks.

• Leave the dishes in the dishwasher for approx. 15 minutes after the end of the programme so that they dry better and can cool down.

• First empty the lower basket, and then the upper basket. This will avoid any water that may be remaining in the upper basket, dripping onto the dishes in the lower basket and leaving water marks.

33

Image 33
Contents Favorit Dear customer Tips on using the appliancePlease read these user instructions carefully Pass them on to any subsequent owner of the applianceContents Installation and Connection Instructions Installation, Connection and Placing into Operation Safety InstructionsChild Safety General SafetyCorrect Use Economical and Ecological Dishwashing DisposalDisposing of the Packaging Material Disposal of Old AppliancesAppliance Features and Control Panel Multi-Display can display Control PanelControl Indicators have the following significance Prior to using for the first timeSetting the water softener Ness and hardness range of the water in your areaPanel Electronic setting Manual settingSpecial salt for the water softener Use special salt or salt substituteWater can be softened in one of two ways Adding special salt VatedPlace the funnel supplied on the container opening Been started. The programme must be cancelled Reset Be cancelled see 3 in 1 functionRinse Aid Activating/deactivating the rinse aid dispenserMulti-display will indicate the current setting Adding rinse aidFully open the rinse aid compartment lid Adjusting Rinse Aid Dosing Daily Use Loading Cutlery and DishesNot be washed in the dishwasher Do not lay small objects e.g. lids in the cutlery rack Loading CutleryTioned horizontally in the upper basket Place knives, small spoons and smallBasket Folded over to the left Loading Pans, Frying Pans Large PlatesTo ease the loading of large items Two right-hand plate insertsAcross one another Folded across one anotherTwo rear plate inserts in the lower Baskets can be folded across one anotherLoading Cups, Glasses Coffee Services Adjusting the Height of the Upper Basket Lowering the Upper BasketRaising the Upper Basket Fill with detergent Filling with DetergentGeneral Advice Special AdviceUse of 3 in 1/ Combi Detergent Tablets Concentrated Detergent Detergent tabletsAutomatic Wash Programmes Addition Type of Soiling Selecting the Wash Programme Programme TableGlass Changing/interrupting/cancelling a programme Starting a programmeChanging a programme Cancelling the programme Reset 1 functionInterrupting the programme by opening the dishwasher door Setting the start delay Setting or changing the start delayChanging the start delay Cancelling the start delayLoad Sensing Sensor Logic Switching Off the DishwasherEmptying the Dishwasher Immediately after the end of the programmeCleaning the Filter Care and CleaningStances What to do, if Error messages are displayedError code After remedying the Filter error, shut the doorWash results are not satisfactory There are problems with the operation of the dish- washerDishes are still dirty Dishes are wet and dullTechnical Data Lower rinse aid dosingThere are dried water drops on the glasses and dishes Sample loading arrangements Upper basket without cutlery trayLower basket with cutlery basket See enclosed installation instructions Installing the DishwasherBuilt-Under Dishwasher Free-Standing AppliancesWork surface must be re-mounted Plinth on free-standing appliances is not adjustableWater Connection Connecting the DishwasherPermitted water pressure Connect the inlet hosePlease take care when installing the water inlet hose Water inlet hose with safety valveWater drain Appliance is automatically pumped out Leak Prevention SystemChanging a fuse Electrical ConnectionConnections Guarantee Conditions Page 08705 929 Customer CareCalls may be recorded for training purposes AEG Hausgeräte GmbH Postfach 90327 Nürnberg Copyright by AEG

60830 specifications

The Electrolux 60830 is a state-of-the-art vacuum cleaner that combines powerful performance with advanced technology to ensure a thorough cleaning experience. Designed for both convenience and efficiency, it caters to a wide range of cleaning needs in modern households.

One of the standout features of the Electrolux 60830 is its impressive suction power, which is driven by a robust motor that provides optimal cleaning performance on various surfaces. The adjustable suction settings allow users to select the appropriate level of power, making it suitable for cleaning delicate fabrics as well as high-traffic carpets. This versatility makes it an ideal choice for families with diverse cleaning requirements.

Another key characteristic of the Electrolux 60830 is its innovative multi-cyclonic technology. This system enhances dust and debris separation from the air, ensuring that the vacuum maintains consistent suction power over time. This means that users don’t have to worry about decreased performance due to clogging or filters needing constant replacement, which ultimately leads to a longer lifespan for the product.

The vacuum cleaner also features a dust container designed for easy emptying, allowing users to dispose of dirt and debris without the hassle of dealing with messy bags. The large capacity of the container minimizes the frequency of emptying, making it perfect for larger cleaning tasks.

For those with allergies, the Electrolux 60830 is equipped with a highly efficient filtration system, which captures fine particles and allergens, helping to purify the air as you clean. This is particularly beneficial for households with pets or allergy sufferers, ensuring a healthier living environment.

The design of the Electrolux 60830 emphasizes user comfort and maneuverability. Its lightweight construction and ergonomic handle make it easy to carry and operate, while the flexible hose and various attachments allow users to reach tight corners and high surfaces with ease. Additionally, the vacuum cleaner is designed with a quiet operation mode to minimize noise, making it suitable for use at any time of day without disturbing the household.

In summary, the Electrolux 60830 combines powerful suction, multi-cyclonic technology, and user-friendly design to make it a top choice for anyone seeking an efficient and effective cleaning solution. Whether tackling everyday dust or deep cleaning tasks, this vacuum cleaner is equipped to handle it all while ensuring comfort and convenience for the user.