Electrolux AOW101E manual Stopping the Cooking Cycle Automatic, Setting Cooking Cycle

Page 25

EN

Note:

- The cooking cycles (steam, combi, convection and regenera- tion) cannot be started until the steam generator is ready, as indi- cated by the corresponding light off (see par. 4.1).

During this period the time count does not start and the Start cooking button flashes; this occurs also when the oven door is opened.

Caution! Risk of burns.

Always open the door with caution when the oven is hot.

4.3.3 STOPPING THE COOKING CYCLE - AUTOMATIC

At the end of the set time, the cooking cycle automatically stops and the oven bell sounds continuously.

Open the door and remove the product.

Caution! Risk of burns.

Always open the door with caution when the oven is hot.

Notes:

- The bell can be stopped in advance by carrying out any opera- tion on the control panel or by opening the door.

The cooking cycle can be stopped manually by keeping the cycle Start/Stop button pressed for 2 seconds.

Shorter presses will be ignored by the oven.

A cycle identical to that just completed can be repeated by press- ing the Start/Stop button again.

4.4MANUAL (Manual control)

SETTING COOKING CYCLE

The MANUAL control mode is used to carry out food cooking manually by setting the various parameters of a cycle.

The food is cooked by heating it and can occur in a certain MODE, with a givenTEMPERATURE, TIME and also HUMIDITY. There- fore these factors must be set in order to perform a COOKING CYCLE.

The oven works mainly by carrying out the operations given in the following sections:

SETTING COOKING CYCLE —- - SELECTING COOKING MODE

- SETTING COOKING TEMPERATURE - SETTING COOKING TIME

- SETTING AND USE OF CORE PROBE - SETTING COOKING HUMIDITY

- MICROWAVE SETTING

- STARTING THE COOKING CYCLE

There are also other sections containing instructions on support functions, such as:

-MANUAL CYCLE (CONTINUOUS COOKING)

-PREHEAT

-UTILITY

-COOKING PHASES IN AUTOMATIC SEQUENCE

Note:

In certain cooking cycles some cooking parameters (humidity, temperature, etc.) cannot be selected.

4.4.1 SELECTING COOKING MODE

1)Press the button P2 ( ) several times and select one of the following cooking modes by turning knob K.

5958 992 00

CONVECTION

 

100

COMBI

300

 

100

STEAM

MICROWAVE

REGENERATION

PAUSE

COMBI is selected in the figure.

For a description of the various cooking modes, refer to par. 3.3

MAIN COOKING MODES.

25

Image 25
Contents Forni CONVEZIONE/VAPORE Microonde Elettrici Electrics Heated Microwave Steam Convection OvensFours À CONVECTION/VAPEUR MICRO-ONDES Électriques Hornos Microondas DE Convección Y Vapor ElectricosSave These Instruction Important Safety InstructionsConservare Queste Istruzioni Istruzioni Importanti PER LA SicurezzaConsignes DE Sécurité Importantes Conserver CES InstructionsImportantes Instrucciones DE Seguridad Conserve Estas InstruccionesUSA CDN Inthenextpicture Mod GN 1/1 Attacco acqua Conden. fumane Ø3/4 Water conn No Text on this Appliance Identification Technical DataIII. Operating Instructions Oven USETechnical Data General CharacteristicsAppliance Description Operating LevelGeneral Instructions Safety of the appliance and invalidate the guaranteeEnvironment CleaningDisposal PackingPlace of Installation II. Installation InstructionsPositioning Electrical ConnectionSupply Water Characteristics Power Cable InstallationWater Connection Water Draining SystemMaintenance Safety DeviceOperation Check Waring Blocking the Drain is HazardousIncorrect oven compartment temperature thermostatting Brief Troubleshooting GuidePositioning of Main Components Oven goes off. Possible causesMicrowave Instructions III. Operating InstructionsDescription of Control Panel Oven Door OpeningOven Door Closing Utilities Special Cooking ModesAdditional Functions Maintenance ServiceABC Steam generator status lightOven USE Switching the Oven onOperating Level a P2 P4 Cooking Higher Temperature AT Core ?Setting Cooking Cycle -- Selecting Cooking Mode Setting Cooking CycleSelecting Cooking Mode Stopping the Cooking Cycle AutomaticSetting Cooking Time Setting Cooking TemperatureP2 P3 Starting the cycleSetting Cooking Humidity Core probe mode deactivation.Operationis only possibleMicrowave Setting Only in CONVECTION, Combi and Regeneration cooking modesStopping of Cooking Cycle Manual Support Function Settings Manual Cycle Continuous CookingUtilities Storing Recipes or Programs Program Program ControlP1 P3 P1 P2 P3 P4Search of Recipes or Programs USE of Prestored Programs or RecipesTime and Date Settings Basic DataLanguage Modifying SET ParametersCleaning and Maintenance Information and ErrorsSwitching OFF in Case of Fault ING Cooking Cycle ManualReplacing Consumable Components Periodical Steam Generator MaintenanceMethod with Chemical Descaler Replacing the compartment lighting lamp FigReplacing door seals Fig Particular Cleaning