EN
Note:
- The cooking cycles (steam, combi, convection and regenera- tion) cannot be started until the steam generator is ready, as indi- cated by the corresponding light off (see par. 4.1).
During this period the time count does not start and the Start cooking button flashes; this occurs also when the oven door is opened.
Caution! Risk of burns.
Always open the door with caution when the oven is hot.
4.4.8 STOPPING OF COOKING CYCLE - MANUAL
At the end of the set time, the cooking cycle automatically stops and the oven bell sounds continuously.
Open the door and remove the product.
Caution! Risk of burns.
Always open the door with caution when the oven is hot.
Notes:
- The bell can be stopped in advance by carrying out any opera- tion on the control panel or by opening the door.
The cooking cycle can be stopped manually by keeping the cycle Start/Stop button pressed for 2 seconds.
Shorter presses will be ignored by the oven.
A cycle identical to that just completed can be repeated by press- ing the Start/Stop button again.
4.5 SUPPORT FUNCTION SETTINGS
4.5.1 MANUAL CYCLE (CONTINUOUS COOKING)
Manual cooking cycles can be set, inhibiting the timer. Follow the instructions of par. 4.3.3 SETTING COOKING TIME until the message “CONTINUOUS” indicating continuous cooking ap- pears on the display.
CONTINUOUS
In this case, the cycle can only be stopped manually by pressing the cycle Start/Stop button for 2 seconds or switching the oven off.
4.5.2 UTILITIES
1)Switch the oven on by pressing the button I (O - I).
2)Set a cooking cycle.
3)Press the button P2 ( 
) several times to select the UTILITIES field.
4)Select the required UTILITY (yellow) with knob K and press the
button P2 ( 
) to set it (white).
To cancel a SET UTILITY (white) press the button P2 (OK) again after selecting it (yellow).
The selectable UTILITIES are those available for the cycle in progress, therefore all, one, a combination or none may be se- lected for a cycle.
The description of the various UTILITIES is given in par. 3.4 SPE- CIAL COOKING MODES (page. 14).
4.5.3MULTIPHASE COOKING IN AUTOMATIC SEQUENCE Food can be cooked with different temperatures during its cycle and therefore in different phases.
The oven enables the execution of programs consisting of sev- eral sequential phases. E.g.
- Phase 1: - convection cycle 392°F (200°C)
-core probe 158°F (70°C)
-Phase 2: - combi cycle 428°F (220°C)
-duration 40 minutes
-Phase 3: - convection cycle 482°F (250°C)
-duration 15 minutes
and so on up to a max. of 6 phases.
During cooking, going from one phase to the next occurs auto- matically, until automatic stopping of the program with completion of the last set phase.
A cycle with several phases is set by carrying out the following operations:
1)switchtheovenon;
2)Set the following for PHASE 1 (refer to par. 4.4 MANUAL): - cooking mode;
- compartment temperature;
- cooking time (or alternatively the core probe temperature).
3)Press the button P2 (
) to select the PHASES field
4)Turn knob K to select the symbol of the NEXT PHASE
5)Press the button P1 ( 
) to confirm PHASE 1.
6)Set new values, as in point 3), but for PHASE 2.
7)To set additional PHASES, repeat points 3, 4, 5 and 6 up to a max. of 7 phases.
8)Now the cooking phase with several phases is set. Introduce the product to be cooked and press the Start cycle button.
_________SET
UTILITY (white)
UTILITY
SELECTED_____________
(yellow)
P2
It will start from PHASE 1 (value1 highlighted in orange) and when completed, automatically goes to PHASE 2 (value 2 highlighted in orange) and so on for the other phases (if set).
PHASE 2 in progress (orange)
The change from one phase to the next is signalled by a brief audible alarm.
At the end of the last phase cooking automatically stops, as pre- viously described, signalled by a double intermittent audible alarm.
5958 992 00
28