Electrolux 50700 manual Connecting the Dishwasher, Water Connection, Permitted water pressure

Page 32

Installation and Connection Instructions

Connecting the Dishwasher

Water Connection

The dishwasher is fitted with safety devices that prevent the wash water returning into the drinking water system and comply with the applicable plumbing regulations.

•The dishwasher can be connected to cold and hot water supplies up to max. 60 °C.

•The dishwasher must not be connected to open hot water appliances or instantaneous water heaters.

Permitted water pressure

Lowest permitted water pressure:	Consult your installer if the water pres-
1 bar (=10 N/cm2 =100 kPa)	sure is less than 1 bar.
Highest permitted water pressure:	In the case of a water pressure greater
10 bar (=100 N/cm2 =1 MPa)	than 10 bar, a pressure reduction valve
	must be used (available from your
	dealer).

	Connect the inlet hose
1	The water inlet hose must not be kinked, crushed or entangled when it
	is being connected up.

0Connect the threaded hose fitting (ISO 228-1:2000) on the water inlet hose to a tap with an external thread (¾ inch). Tighten the threaded hose fitting hand tight only.

3	• In order that access to the tap in the kitchen is not limited by the use
	of the dishwasher, we recommend the installation of an additional

tap, or fitting a two way adapter to the existing tap.

• If you need a longer water inlet hose than that supplied, VDE approved complete hose sets are to be used. These are available from your local Service Force Centre.

32

Image 32

Contents Ökofavorit Tips on using the appliance Dear customerPlease read these user instructions carefully Pass them on to any subsequent owner of the applianceContents Installation and Connection Instructions Safety Instructions Installation, Connection and Placing into OperationChild Safety General SafetyCorrect Use Disposal Economical and Ecological DishwashingDisposing of the Packaging Material Disposal of Old AppliancesAppliance Features and Control Panel Prior to using for the first time Control panelHardness range of the water in your area Adjust the Water SoftenerSalt Filling with Salt for the Water Softener Fill with dishwasher saltUse dishwasher salt Open the door, remove the lower rackFilling with Rinse Aid Ough rinsing, spot and streak free dryingAge the appliance Fill with rinse aidAdjusting Rinse Aid Dosing Daily UseLoading Cutlery and Dishes Not be washed in the dishwasherLoading Cutlery Loading Pans, Frying Pans and Large Plates Load large and heavily soiled dishes in the lower rackLoading Cups, Glasses Coffee Services Adjusting the Height of the Upper Basket Lowering the Upper Basket TypeLowering the Upper Basket Raising the Upper BasketFilling with Detergent Fill with detergentBio Wash Programmes and Concentrated Detergents Detergent RecommendationsSelecting the Wash Programme Programme Table SoilingChanging/Interrupting/Cancelling Start the Wash ProgrammeWash Programme Changing the wash programmeSetting or Changing the Delay Start Timer Cancelling the wash programmeDishwasher is switched on again Changing the delay startEmptying the Dishwasher Care and CleaningSwitching Off the Dishwasher Cleaning the Filter Error messages What to do, ifThere are problems with the operation of the dish- washer Wash results are not satisfactoryDishes are still dirty Dishes are wet and dullThere are dried water drops on the glasses and dishes Technical DataLower rinse aid dosing Sample loading arrangements Upper basket Lower basket with cutlery basketCannot be kinked or crushed Installing the DishwasherFree-Standing Appliances Unscrew the screws 1 from the elbows on the back side Connecting the Dishwasher Water ConnectionPermitted water pressure Connect the inlet hoseWater drain Leak Prevention System Appliance is automatically pumped outElectrical Connection Changing a fuseConnections Guarantee Conditions Page Calls may be recorded for training purposes 08705 929Customer Care AEG Hausgeräte GmbH Postfach 90327 Nürnberg Copyright by AEG