Emerson 2700, 1700 installation manual Specifications

Page 61

Specifications

One frequency/pulse output (Model 1700 transmitters) or frequency/pulse/discrete output (Model

2700 transmitters):

•Not intrinsically safe

•Internally powered (active)

•Maximum current: 100 mA

•Output voltage: +24 VDC ±3%, with a 2.2 kohm internal pull-up resistor

•Frequency/pulse output (Model 1700/2700):

-Can be used to indicate either flow rate or total; Model 1700 output reports the same flow variable as the mA output, Model 2700 output is independent from mA output

-Scalable to 10,000 Hz

-Linear with flow rate to 12,500 Hz

-Configurable polarity: active high or active low

•Discrete output (Model 2700 only):

-Can report event 1, event 2, event 1 or 2, flow direction, flow switch, calibration in progress, or fault

-Maximum sink capability: 500 mA

-Configurable polarity: active high or active low

Model 1700/2700 transmitters with intrinsically safe outputs option board (output option code D)

Model 1700 has one 4–20 mA output; Model 2700 has two 4–20 mA outputs:

•Intrinsically safe

•Externally powered (passive)

•Isolated to ±50 VDC from all other outputs and earth ground

•Maximum input voltage: 30 VDC, 1 watt maximum

•Model 1700 can report mass flow or volume flow; Model 2700 can report mass flow, volume flow, density, temperature, or drive gain; transmitters with the petroleum measurement application (API) or enhanced density application can also report standard volume flow and density at reference temperature

•Linear with process from 3.8 to 20.5 mA, per NAMUR NE43 (June 1994)

•Maximum load limits: see following chart

Output Wiring – Intrinsically Safe

Output Wiring – Configurable I/O Output Wiring – Fieldbus/PROFIBUS

Specifications

Installation Manual

57

Image 61

Contents Micro Motion Model 1700 Model 2700 Transmitters Page Contents Index Before You Begin SafetyOverview Flowmeter components Flowmeter documentation 1Flowmeter documentation resources Transmitter installation proceduresMicro Motion customer service Installation architecture Installing the Transmitter1Installation types Power source Temperature limitsAC power requirements Determining an appropriate location1Typical power cable resistances at 68 F 20 C DC power requirementsMaximum cable lengths Accessibility for maintenance2Maximum cable lengths Mounting the transmitter2Rotating the transmitter Integral installations34-wire remote Wall mount or pipe mount 59-wire remote Wall mount or pipe mount 3 9-wire remote installationsMounting the remote core processor 6Transmitter/core processor assembly Exploded view7Remote core processor Wall mount or pipe mount 3Grounding methods for flowmeter components Grounding the flowmeter componentsRotating the display Supplying powerInstalling the Transmitter 10Display components Cable types Wiring the Transmitter to the Sensor2 9-wire cable 1 4-wire cableWiring for 4-wire remote installations 3Wiring to the mating connector Core processor on transmitter Wiring for 9-wire remote installationsSubtask 1 Wire the remote core processor to the transmitter 5Cable glands 7Wrapping the shield drain wires 10Gland body and core processor housing 129-wire cable between sensor and core processor Subtask 2 Wiring the sensor to the remote core processorWiring the Transmitter to the Sensor Output wiring Output Wiring Model 1700/2700 Analog TransmittersOutput terminals and output types 1Terminals and output types1Basic analog wiring 2HART/analog single-loop wiring Smart Family Output Wiring Intrinsically Safe Safe area mA output wiring Safe area output wiring2Safe area mA output load resistance values 5Safe area frequency/discrete output wiring Safe area frequency/discrete output wiringHazardous area safety parameters Hazardous area output wiringHazardous area voltage 2Safety parametersHazardous area current Hazardous area capacitanceHazardous area frequency/discrete output wiring Hazardous area mA output wiringHazardous area Channel configuration Output Wiring Model 2700 Configurable I/O TransmittersMA output wiring 1Channel configuration2Basic mA wiring Frequency output wiring 5Frequency output Terminals 3 & 4 Channel B Internal power 7Frequency output Terminals 5 & 6 Channel C Internal power 9Discrete output 1 Terminals 3 & 4 Channel B Internal power Discrete output wiring11Discrete output 2 Terminals 5 & 6 Channel C Internal power Volts Voltage Output Level High 2Input voltage ranges for external power Discrete input wiring16Discrete input Terminals 5 & 6 Channel C Internal power Micro Motion Model 1700 and 2700 Transmitters 1Connecting the fieldbus communication wires Foundation fieldbus wiring2Connecting the PROFIBUS-PA communication wires PROFIBUS-PA wiringFunctional specifications SpecificationsPower connection Service port connectionCore processor connection Input/output signals Input signal from sensorFisco and Fnico approval Specifications Operating Absolute minimum = 100 Ohms for V supply 25.6 volts Specifications Digital communication Service portHART/Bell202 Foundation fieldbus or PROFIBUS-PA transmittersEnvironmental requirements Ambient temperature limits Power supplyAmbient temperature effect EMC complianceTransmitter UL and CSAOutputs Atex and IECExPhysical specifications Performance specificationsHousing MountingDimensions WeightInterface/display Dimensions in inchesmm Inches Dimensions in mm Or M20 × 11/16 160 13/16 139 ″-14 NPT 158 182 × Ø3/8 13/16 148 15/16 × 1/2″-14 NPT Figure A-5Dimensions Remote core processor Atex IndexRemote core processor with remote Index Micro Motion Model 1700 and 2700 Transmitters Page 20001700