Honeywell Central Heating Cooker Natural Gas manual Lining of Existing Chimneys, Flue Pipes

Page 21

INSTALLATION

Flue Pipes.

3.7These should only be used to connect a gas burning appliance to one of the types of chimney previously mentioned. Any flue type serving a gas appliance must be kept clear of any combustible materials including any materials likely to be located near the installation by the householder. The minimum air gap clearance that must be maintained is 25 mm (1'').

Flue pipes may be constructed from the following materials.

3.8Sheet metal as described in BS 715 stainless steel flue pipe, cast iron flue pipe as described in BS 41, any flue pipe material described in the Building Regulations relating to flue pipes suitable for solid fuel and oil burning appliances. All flue pipes should be constructed such that any condensation is retained by the flue pipe system. Systems with spigot and socket joints must be fitted with the sockets uppermost.

4.LINING OF EXISTING CHIMNEYS

4.1Before using any existing chimney or refitting a gas appliance, it is vital to check that the chimney is safe. Oversized, leaking or rough chimneys can be inefficient and dangerous.

4.2There are two basic existing types of chimney re-lining product suitable for use with gas appliances. It is most important that the chimney is swept and thoroughly cleaned before installing a liner so as to remove previous combustion deposits, which have the potential to damage the liner.

Flexible Stainless Steel.

4.3Recommended where any existing chimney is to be used for a gas-fired appliance. Flexible stainless steel liners must be certified to BS 715. When replacing an existing appliance connected to a chimney lined with a metallic liner, the liner should be replaced.

Rigid Stainless Steel Flue Pipe

4.4Type 316 or 304 stainless steel, not less than 0.55 mm thick.

Rain Cap (Approved for gas use)

 

 

Cement Mortar

HEIGHT=3M

 

Plate Clamp

Back fill with Vermiculite

 

 

 

 

Insulation or similar

Brick Chimney

EFFECTIVE

 

Bends must be no less than 135°

Stainless Steel

 

MIN

Flexible Flue

Vitreous Enamelled Steel or

Liner

 

Stainless Steel with Cleaning

 

 

Cover

 

 

 

Seal Liner

 

 

into Flue Socket

 

 

with Fire Cement

MIN RISE

 

BEFORE BEND

 

=600MM

 

COVENTIONAL BRICK CHIMNEY WITH LINER

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Central Heating Cooker Information for the Installer and Service Engineers Health and SafetyInsulation and Seals GLUES, Sealants & PaintDo not Cover the Outlet on the TOP Rear Splash Back Cover General Safety InstructionsInstallation Instructions ContentsUser Instructions Servicing InstructionsImportant Customer Notice Important InformationMain Oven Users InstructionsLower Oven HotplatesLighting the Burners Switching OFFProgrammer -COOKER Cooker BurnerCentral Heating Blocked Flue Approx Time Top Oven Bottom Oven HotplateMeat Oven Cooking GuidePoultry CasserolesPastries Uses for the ProgrammerCold Start Cooking Care of the Cooker User Cooker Fault Finding User Boiler Fault Finding Charge will be made where Step by step guide to reporting a fault with your appliancePlease Note Enamelled Parts on your cookerTechnical Details Site Requirements AIR Supply and VentilationOverlap the Black Enamel TOP Plate Central Heating Cooker Dimensions General Description Health and Safety at Work ActGAS Supply InstallationFlue & Chimney Requirements Types of Chimney and Flue SystemsFlue Pipes Lining of Existing ChimneysFlexible Stainless Steel Rigid Stainless Steel Flue PipeWind Effects on Buildings Flue SystemsHigh LOW Important Notes Roof Pitch Over Flat RoofRecommended flue positions for some roof conditions Flue TerminationWater Systems Plumbing ‘Y’ Plan Open SystemsPlumbing ‘S’ Plan Cable Fixing Gland Electrical SupplyCooker Internal Wiring Wiring ‘S’ Plan Wiring ‘Y’ Plan Replacement of Parts ServicingBoiler Burner Removal Ignition & Ionisation Electrodes Cooker BurnerIgnition Electrode Removal Ionisation Electrode RemovalBoiler Thermostats Cooker ThermostatsCooker Programmer Burner Reset Switches Service Procedures for BurnersBlocked Flue Overheat Themostat Failure to do SO will Enable Flue Gases to Enter the Room Boiler Heat ExchangerCooker Flueways Guide to Fault Finding Service EngineerYES Fault Finding Not Shown Spare Parts BurnerSpare Parts List Exploded View 29 30 31Page Page Division of Gazco Limited

Central Heating Cooker Natural Gas specifications

The Honeywell Central Heating Cooker powered by natural gas is a prime example of modern kitchen technology, seamlessly blending efficiency, convenience, and safety features to create an exceptional cooking experience. With Honeywell's years of expertise in heating solutions, this cooker is designed to provide not only a reliable cooking tool but also an efficient heating source for your home.

One of the standout features of the Honeywell Central Heating Cooker is its efficient natural gas operation. Utilizing natural gas ensures that the cooker operates at a lower cost compared to electric models, making it an economical choice for households. The heat produced by natural gas is immediate, allowing for faster cooking times and better temperature control, ensuring that meals are prepared quickly and to precise specifications.

The cooker incorporates advanced heating technologies, including uniform heat distribution that minimizes hot spots and ensures even cooking across pans. This is particularly beneficial when preparing complex dishes that require different cooking techniques simultaneously. The integrated thermostat monitors the cooking temperature in real-time, allowing for perfect results every time.

In terms of safety, the Honeywell Central Heating Cooker is equipped with multiple safety mechanisms. An automatic shut-off feature provides peace of mind, especially for busy households. This is complemented by flame failure devices that detect if the flame goes out unexpectedly, cutting off the gas supply to prevent potentially hazardous situations.

The design of the Honeywell cooker is also user-friendly, offering intuitive controls that make it easy to adjust the settings as needed. The model features spacious cooking surfaces with multiple burners, accommodating various pot and pan sizes while optimizing workspace in the kitchen. Additionally, the sleek stainless steel finish not only looks modern but is also easy to clean.

Furthermore, energy efficiency is a key characteristic of the Honeywell Central Heating Cooker. It adheres to stringent energy standards, helping users reduce their carbon footprint while also saving on energy costs. This combination of efficiency, safety, and performance sets Honeywell apart as a leader in cooking appliances.

Ultimately, the Honeywell Central Heating Cooker is not just a cooking appliance; it represents a harmony of functionality, safety, and innovation. Whether you are a professional chef or a home cook, this cooker promises to elevate your cooking experience while also providing an efficient heating solution for your home.
Top Page Image Contents