Honeywell Central Heating Cooker Natural Gas Cooker Burner, Ignition & Ionisation Electrodes

Page 32

SERVICING

3. COOKER BURNER

To remove the cooker burner, the boiler burner needs to be removed first following the section on boiler burner removal

a)Remove the lower panel as detailed above.

b)Remove the boiler burner as detailed previously.

c)Disconnect the cooker burner 6 way plug, the ignition lead, and the ionisation lead from the control box.

d)The burner is connected to the gas supply pipe via a union with a sealing washer which needs to be undone, retain the sealing washer, replace if necessary. See diagram 3.

e)Remove the Front Insulation piece from the underside of the cooker combustion chamber, undo the nut an mudguard washer. See diagram 4.

f)Access to the securing nuts will then be possible. The cooker burner is fixed to the cooker by a bayonet type flange. Undo the two flange nuts (13mm) and whilst supporting the burner rotate the burner clockwise. Gently lower the burner and then out of the chamber.

g)Remove the ignition control box by unscrewing the single retaining screw and fit to the new burner assembly, refit both ignition & ionisation probe leads.

h)Fit the new burner ensuring it is the direct replacement and reassemble in reverse order.

4. IGNITION & IONISATION ELECTRODES

Ignition Electrode Removal

a)Remove the burners as described in the previous sections.

b)Disconnect the HT leads from the ignition control box and electrode (push fit). Remove the single retaining screws and remove the electrode.

c)Fit replacement and check electrode to burner head gap is in accordance with specification (See Fig. 7)

d)Refit in reverse order

Ionisation Electrode Removal

a)Remove the burners as described in the previous sections.

b)Disconnect the white lead from the ignition control box.

c)The lead is permanently attached to the electrode and is replaced at the same time.

d)Undo the single retaining screw and carefully remove the electrode Fit replacement and check electrode to burner gap is in accordance with specification (See Fig. 7 )

e)Refit in reverse order.

32

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Central Heating Cooker Health and Safety Information for the Installer and Service EngineersInsulation and Seals GLUES, Sealants & PaintGeneral Safety Instructions Do not Cover the Outlet on the TOP Rear Splash Back CoverContents Installation InstructionsUser Instructions Servicing InstructionsImportant Information Important Customer NoticeUsers Instructions Main OvenLower Oven HotplatesSwitching OFF Lighting the BurnersProgrammer -COOKER Cooker BurnerCentral Heating Approx Time Top Oven Bottom Oven Hotplate Blocked FlueOven Cooking Guide MeatPoultry CasserolesCold Start Cooking PastriesUses for the Programmer Care of the Cooker User Cooker Fault Finding User Boiler Fault Finding Step by step guide to reporting a fault with your appliance Charge will be made wherePlease Note Enamelled Parts on your cookerTechnical Details Overlap the Black Enamel TOP Plate Site RequirementsAIR Supply and Ventilation Central Heating Cooker Dimensions Health and Safety at Work Act General DescriptionInstallation GAS SupplyFlue & Chimney Requirements Types of Chimney and Flue SystemsLining of Existing Chimneys Flue PipesFlexible Stainless Steel Rigid Stainless Steel Flue PipeFlue Systems Wind Effects on BuildingsHigh LOW Important Notes Roof Pitch Over Flat RoofFlue Termination Recommended flue positions for some roof conditionsWater Systems Open Systems Plumbing ‘Y’ PlanPlumbing ‘S’ Plan Electrical Supply Cable Fixing GlandCooker Internal Wiring Wiring ‘S’ Plan Wiring ‘Y’ Plan Boiler Burner Removal Replacement of PartsServicing Cooker Burner Ignition & Ionisation ElectrodesIgnition Electrode Removal Ionisation Electrode RemovalCooker Programmer Boiler ThermostatsCooker Thermostats Blocked Flue Overheat Themostat Burner Reset SwitchesService Procedures for Burners Cooker Flueways Failure to do SO will Enable Flue Gases to Enter the RoomBoiler Heat Exchanger Service Engineer Guide to Fault FindingYES Fault Finding Spare Parts Burner Not ShownSpare Parts List 29 30 31 Exploded ViewPage Page Division of Gazco Limited

Central Heating Cooker Natural Gas specifications

The Honeywell Central Heating Cooker powered by natural gas is a prime example of modern kitchen technology, seamlessly blending efficiency, convenience, and safety features to create an exceptional cooking experience. With Honeywell's years of expertise in heating solutions, this cooker is designed to provide not only a reliable cooking tool but also an efficient heating source for your home.

One of the standout features of the Honeywell Central Heating Cooker is its efficient natural gas operation. Utilizing natural gas ensures that the cooker operates at a lower cost compared to electric models, making it an economical choice for households. The heat produced by natural gas is immediate, allowing for faster cooking times and better temperature control, ensuring that meals are prepared quickly and to precise specifications.

The cooker incorporates advanced heating technologies, including uniform heat distribution that minimizes hot spots and ensures even cooking across pans. This is particularly beneficial when preparing complex dishes that require different cooking techniques simultaneously. The integrated thermostat monitors the cooking temperature in real-time, allowing for perfect results every time.

In terms of safety, the Honeywell Central Heating Cooker is equipped with multiple safety mechanisms. An automatic shut-off feature provides peace of mind, especially for busy households. This is complemented by flame failure devices that detect if the flame goes out unexpectedly, cutting off the gas supply to prevent potentially hazardous situations.

The design of the Honeywell cooker is also user-friendly, offering intuitive controls that make it easy to adjust the settings as needed. The model features spacious cooking surfaces with multiple burners, accommodating various pot and pan sizes while optimizing workspace in the kitchen. Additionally, the sleek stainless steel finish not only looks modern but is also easy to clean.

Furthermore, energy efficiency is a key characteristic of the Honeywell Central Heating Cooker. It adheres to stringent energy standards, helping users reduce their carbon footprint while also saving on energy costs. This combination of efficiency, safety, and performance sets Honeywell apart as a leader in cooking appliances.

Ultimately, the Honeywell Central Heating Cooker is not just a cooking appliance; it represents a harmony of functionality, safety, and innovation. Whether you are a professional chef or a home cook, this cooker promises to elevate your cooking experience while also providing an efficient heating solution for your home.
Top Page Image Contents