Honeywell Central Heating Cooker Natural Gas Lighting the Burners, Switching OFF, Cooker Burner

Page 7

USERS INSTRUCTIONS

5. LIGHTING THE BURNERS

COOKER BURNER

5.1The cooker burner is fully automatic and requires no manual intervention to light. Ensure that the programmer is in the ON mode, neon glowing, and turn the thermostat to the desired temperature. The cooker light will illuminate and once the desired temperature has been reached it will extinguish.

BOILER BURNER

5.2The boiler burner is fully automatic in operation and requires no manual intervention to light. Ensure that any external controls are on and calling for heat and that the thermostat is turned on to the desired temperature. The boiler light will illuminate and once the desired temperature has been reached it will extinguish.

6. SWITCHING OFF

Please note the section on frost protection. (page 1)

6.1For short periods: Turn all the external controls to off and turn the boiler thermostat to ‘off’. Turn the cooker thermostat to ‘off’ and switch the cooker programmer to off.

6.2For Long Periods: Turn all external and internal controls to off, switch off the electrical supply to the unit.

7.PROGRAMMER -COOKER

6.1In general the programmer is used either to turn ‘On’ of ‘Off’ the cooker manually or automatically.

Programmer Setting instructions

6.2On initial power-up the unit should be re-set to wake up the unit remove the programmers button cover, see figure 2. To re-set the unit press and hold the four buttons shaded grey, see diagram 1.

1

SELECT PROG

1 HR

ADV

2

ON

OFF

AUTO ALLDAY + 1 HOUR ADVANCE

SELECTPROG

1 HR

ADV

Unit with programming cover removed

Factory programming.

6.3The unit can provide up to 3 On/Offs each day. In order to simplify programming a factory pre-set programme is included. This can be easily altered to suit household lifestyle and needs.

Event 1

ON = 06:30 AM

OFF = 08:30 AM

Event 2

ON = 12:00 PM

OFF = 02:00 PM

Event 3

ON = 05:00 PM

OFF = 10:30 PM

Setting the time of the day.

6.4Remove the programmers button cover.

6.5Press PROG to enter programming mode. The display will be as in diagram 3 and the colon in the display will not flash.

3

ON

OFF

AUTO ALLDAY + 1 HOUR

ADVANCE

6.6Press and release the + or - button to change the time in one minute increments. Note: If the button is held down, the time will change in increments of 10 minutes.

6.3 Figure 2 depicts how the display will look after being re-set.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Central Heating Cooker GLUES, Sealants & Paint Health and SafetyInformation for the Installer and Service Engineers Insulation and SealsDo not Cover the Outlet on the TOP Rear Splash Back Cover General Safety InstructionsServicing Instructions ContentsInstallation Instructions User InstructionsImportant Customer Notice Important InformationHotplates Users InstructionsMain Oven Lower OvenCooker Burner Switching OFFLighting the Burners Programmer -COOKERCentral Heating Blocked Flue Approx Time Top Oven Bottom Oven HotplateCasseroles Oven Cooking GuideMeat PoultryUses for the Programmer PastriesCold Start Cooking Care of the Cooker User Cooker Fault Finding User Boiler Fault Finding Enamelled Parts on your cooker Step by step guide to reporting a fault with your applianceCharge will be made where Please NoteTechnical Details AIR Supply and Ventilation Site RequirementsOverlap the Black Enamel TOP Plate Central Heating Cooker Dimensions General Description Health and Safety at Work ActTypes of Chimney and Flue Systems InstallationGAS Supply Flue & Chimney RequirementsRigid Stainless Steel Flue Pipe Lining of Existing ChimneysFlue Pipes Flexible Stainless SteelRoof Pitch Over Flat Roof Flue SystemsWind Effects on Buildings High LOW Important NotesRecommended flue positions for some roof conditions Flue TerminationWater Systems Plumbing ‘Y’ Plan Open SystemsPlumbing ‘S’ Plan Cable Fixing Gland Electrical SupplyCooker Internal Wiring Wiring ‘S’ Plan Wiring ‘Y’ Plan Servicing Replacement of PartsBoiler Burner Removal Ionisation Electrode Removal Cooker BurnerIgnition & Ionisation Electrodes Ignition Electrode RemovalCooker Thermostats Boiler ThermostatsCooker Programmer Service Procedures for Burners Burner Reset SwitchesBlocked Flue Overheat Themostat Boiler Heat Exchanger Failure to do SO will Enable Flue Gases to Enter the RoomCooker Flueways Guide to Fault Finding Service EngineerYES Fault Finding Not Shown Spare Parts BurnerSpare Parts List Exploded View 29 30 31Page Page Division of Gazco Limited

Central Heating Cooker Natural Gas specifications

The Honeywell Central Heating Cooker powered by natural gas is a prime example of modern kitchen technology, seamlessly blending efficiency, convenience, and safety features to create an exceptional cooking experience. With Honeywell's years of expertise in heating solutions, this cooker is designed to provide not only a reliable cooking tool but also an efficient heating source for your home.

One of the standout features of the Honeywell Central Heating Cooker is its efficient natural gas operation. Utilizing natural gas ensures that the cooker operates at a lower cost compared to electric models, making it an economical choice for households. The heat produced by natural gas is immediate, allowing for faster cooking times and better temperature control, ensuring that meals are prepared quickly and to precise specifications.

The cooker incorporates advanced heating technologies, including uniform heat distribution that minimizes hot spots and ensures even cooking across pans. This is particularly beneficial when preparing complex dishes that require different cooking techniques simultaneously. The integrated thermostat monitors the cooking temperature in real-time, allowing for perfect results every time.

In terms of safety, the Honeywell Central Heating Cooker is equipped with multiple safety mechanisms. An automatic shut-off feature provides peace of mind, especially for busy households. This is complemented by flame failure devices that detect if the flame goes out unexpectedly, cutting off the gas supply to prevent potentially hazardous situations.

The design of the Honeywell cooker is also user-friendly, offering intuitive controls that make it easy to adjust the settings as needed. The model features spacious cooking surfaces with multiple burners, accommodating various pot and pan sizes while optimizing workspace in the kitchen. Additionally, the sleek stainless steel finish not only looks modern but is also easy to clean.

Furthermore, energy efficiency is a key characteristic of the Honeywell Central Heating Cooker. It adheres to stringent energy standards, helping users reduce their carbon footprint while also saving on energy costs. This combination of efficiency, safety, and performance sets Honeywell apart as a leader in cooking appliances.

Ultimately, the Honeywell Central Heating Cooker is not just a cooking appliance; it represents a harmony of functionality, safety, and innovation. Whether you are a professional chef or a home cook, this cooker promises to elevate your cooking experience while also providing an efficient heating solution for your home.
Top Page Image Contents