Wolf WKGC 126622, WKGDX 126624, WKGX 126623 Computer Control WKGC/WKGCX, Operation Setup Mode

Page 26

FULL SIZE GAS CONVECTION OVENS - SERVICE PROCEDURES AND ADJUSTMENTS

F.The stop cable must be positioned where it moves freely and does not get pinched.

3.Position door chain assembly to factory setting if the conditions in step 2 are not met.

4.If right door does not lead the left door in closing:

A.Loosen locknut on both turnbuckles.

B.Loosen left turnbuckle.

C.Tighten right turnbuckle.

D.Tighten locknut on both turnbuckles.

5.If the right door leads the left door by more than 3/8 inch:

A.Loosen locknut on both turnbuckles.

B.Loosen right turnbuckle.

C.Tighten left turnbuckle.

D.Tighten locknut on both turnbuckles.

6.Check doors for proper operation.

NOTE: The locknuts must be tight during testing or the adjustment will not hold.

A.If doors do not close properly, repeat step 4, 5 and 6.

B.If doors operate properly, continue with procedure.

7.Install the lower front cover.

COMPUTER CONTROL

(WKGC/WKGCX)

Operation

Refer to the Owner's Manual for specific operating instructions.

Setup Mode

NOTE: Use the setup mode to verify that the control is configured to the factory settings which result in the proper operation of the oven. If the CAL1 parameter is other than zero, determine if it is still needed before resetting to zero. See COMPUTER CONTROL CALIBRATION (WKGC/WKGCX).

CAUTION: Changing the C_F, InP1, rL1 & rH1 parameters will default all menus.

1.Use this key sequence to access the setup mode.

Up arrow; Rack 1; Temperature; Temperature; Down arrow; Rack 1

2.Once in the setup mode the display will alternate between the parameter and programmed data.

•To change data to the factory setting, use the arrow keys.

•To select the next parameter, press the Rack 1 key.

•After the last Parameter and Data is viewed, press the Rack 1 key a final time to exit the setup mode and return to operations mode. The current set point temperature will be displayed.

•After 1 minute of no key activations, the control will return to operation mode.

3.Listed are the parameters and data you should find.

F32700 (February 2006)		Page 26 of 64

Image 26

Contents WKG Series Full Size GAS Convection Ovens Table of Contents Computer Control Models Only Introduction Installation Operation Cleaning LubricationSpecifications ToolsBottom Front Cover Covers and PanelsTop Front Cover Control PanelRemovable Components Procedure Control Panel ComponentsComponent Panel Components Temperature Probe WKGD/WKGDX GAS BurnerGAS Orifice GAS Solenoid ValveIgnition Control Module Spark Igniter Flame SenseBlower and Motor Oven Doors and Bearings Independent Doors Assembly Removal Oven Doors Simultaneous DoorsDoor Window Door Catch Ball Assembly Independent DoorsDisassembly Door Switch Lamp High Limit ThermostatInterior Lights Lamp Assembly Cooling FANService Procedures and Adjustments Solid State Temperature Control Calibration WKGD/WKGDXSolid State Temperature Mechanical Thermostat Calibration WKG/WKGXTemperature Probe Test WKGD/WKGDX Temperature Probe Test WKGD/WKGDXGAS Pressure Adjustment Temp F OhmsDoor Switch Adjustment Verification of Spark AT Ignitor Blower Adjustment Door Adjustment Door Catch Ball Adjustment Independent DoorsProcedure IntroductionOperation Setup Mode Computer Control WKGC/WKGCXSolid State Relay Test Computer Control Calibration WKGC/WKGCXProbe Test Component Function Function Switch S3Door Switch Motor Speed Relay R1 Solid State Temperature ControlBlower Motor Computer ControlComponent Location Temperature ProbeMechanical Temperature Control Gas Valve Dual SolenoidWKG/WKGX Plug, Socket and Components Standard Controls WKGD/WKGDX Plug, Socket and Components Standard Controls Full Size GAS Convection Ovens Electrical Operation WKGC/WKGCX Plug, Socket and Components Roast & Hold Standard Normal Roast Cycle Sequence of OperationWKG, Wkgx With Roast & Hold Option Mechanical KX Thermostat Timer Cycle Normal Roast Cooking Roast and Hold CycleFull Size GAS Convection Ovens Electrical Operation Timer Cycle Roast & Hold Cooking State Temperature Control WKGD, Wkgdx With Roast & Hold Option SolidTimer Cycle Normal Roast Cooking Roast and Hold Cycle Timer Cycle Roast & Hold Cooking Oven Cool Cycle Solid State Temperature Control Roast & Hold Standard on Computer Model Roast Cycle Normal CookingFull Size GAS Convection Ovens Electrical Operation Temperature and Time Cycle Cooking Oven Cool Cycle Computer Control ModelSchematics WKG, Wkgx Mechanical KX ControlsWKG, Wkgx Mechanical KX Controls, Roast & Hold Option WKGD, Wkgdx Solid State Temperature Control Full Size GAS Convection Ovens Electrical Operation WKGC, Wkgcx Computer Control Roast & Hold Standard Wiring Diagrams Full Size GAS Convection Ovens Electrical Operation WKG, Wkgx Mechanical KX Controls, Roast & Hold Option Full Size GAS Convection Ovens Electrical Operation WKGD, Wkgdx Solid State Temperature Control Full Size GAS Convection Ovens Electrical Operation Full Size GAS Convection Ovens Electrical Operation Full Size GAS Convection Ovens Electrical Operation WKGC, Wkgcx Computer Control Roast & Hold Standard Full Size GAS Convection Ovens Electrical Operation Troubleshooting ALL ModelsError Codes Computer Control Models onlyCondensed Spare Parts List Description