KitchenAid KSSC42FTS, KSSC48FTS, KSSC36FTS Overlay Series Door Panel and CabinetryClearance

Page 11

Overlay Series Door Panel and CabinetryClearance

The custom door panels and adjacent cabinetry must be designed so that there is sufficient clearance for the doors to swing open. If the refrigerator is to be installed close to the wall, see “Door Swing 90°” on next page.

Hinge

Door Swing 110˚

Actual Size

Refrigerator to

Cabinetry Clearance

Refrigerator

Side Trim

11/2"

(3.8 cm)

11/4"

(3.2 cm)

1"

(2.5 cm)

Cabinetry

1/4" (6.35 mm)

1/2" (1.3 cm)

3/4" (1.9 cm) 1" (2.5 cm)

1/2"

NOTE: Allow ¹⁄₂"

(1.3 cm) clearance

(1.3 cm)

between overlay

 

3/4"

 

panel and cabinetry.

 

 

 

(1.9 cm)

 

 

 

 

1"

 

 

 

(2.5 cm)

NOTE: For Overlay Series models, rout the hinge side of the custom door panels to a radius that is equal to at least half the thickness of the panel if a 130° door swing is desired. See “Adjust Doors.”

 

Backer

Overlay

Door

 

 

Panel

Panel

 

 

 

11/4"

(3.2 cm)

11/2"

(3.8 cm)

Spacer Panel

When the doors are closed the refrigerator will extend beyond the face of the adjacent cabinetry to some degree.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Side by Side BUILT-IN Refrigerator Table of Contents/Índice/Table des matièresTable DES Matières Table of ContentsÍndice Your safety and the safety of others are very important Refrigerator SafetyClassic Series ModelsSide by Side Non-Dispensing Refrigerators Architect SeriesComplete Series Side by Side Dispensing RefrigeratorsLocation Requirements Installation RequirementsTools and Parts Recommended Grounding Method Electrical RequirementsTipping Radius Water Supply RequirementsModel Product DimensionsSide View Front View Top View48 121.9 cm Models Door Swing Dimensions36 91.4 cm Models 42 106.7 cm ModelsOverlay Series Door Panel and CabinetryClearance DoorHinge Model a Overlay Series Custom Panels and Handle KitsDecorative Overlay Panel Dispenser frame attaches to the panel with 4 screws Backer PanelsDispenser Frame dispenser models only Model DClassic Series Factory Panels and Kits Top Grille Panel Classic Series Custom PanelsDoor Panels for Non-dispenser Models To remove the dispenser frame Door Panels for Dispenser ModelsDispenser Frame Classic series dispenser models Overlay Series Custom Side Panels Classic, Architect and Complete Series Custom Side PanelsMeasure the distance from point a as shown to back wall Installation InstructionsUnpack the Refrigerator Move the Refrigerator into House Install Anti-Tip BoardsTo Install Anti-tip Boards Reduce Tipping RadiusStyle 2-Copper Line Connection Connect the Water SupplyConnect to Water Line Parts Needed Style 1-Shutoff Valve ConnectionConnect to Refrigerator Plug in RefrigeratorMove Refrigerator to Final Location Parts SuppliedDoor Panels Install Classic Series Custom PanelsLevel and Align Refrigerator Check refrigerator level and adjustment. Adjust if needed Install Overlay Series Custom PanelsDoor Panel Installation Classic and Architect Models Adjust DoorsDoor Height Adjustment Door Swing AdjustmentDoor-to-Door or Door-to-Refrigerator Trim Adjustment Install Side PanelInstall Base Grille Style 2 Non-Dispenser Models Complete InstallationWater System Preparation Style 1 Dispenser ModelsSu seguridad y la seguridad de los demás es muy importante Seguridad DEL RefrigeradorSerie Classic ModelosRefrigeradores de dos puertas sin despachador Serie ArchitectSerie Complete Refrigeradores de dos puertas con despachadorMedidas de la abertura Requisitos DE InstalaciónPiezas y herramientas Requisitos de ubicaciónMétodo de conexión a tierra recomendado Arco de vuelco Requisitos del suministro de aguaMedidas del producto Modelos de 48 121,9 cm Medidas de oscilación de las puertasModelos de 36 91,4 cm Modelos de 42 106,7 cm Panel Oscilación de Modelo a Panel decorativo recubiertoEl marco del despachador se sujeta al panel con 4 tornillos Paneles de soporteMarco del despachador Solamente en modelos con despachador Modelo DPaneles y juegos de fábrica de la serie Classic Modelo Panelesa la medida para la serie ClassicPaneles de puerta para modelos sin despachador Panel de la rejilla superiorPaneles de puerta para modelos con despachador Adorno lateral Medidas para la instalación empotradaMedidas del refrigerador y del adorno lateral RefrigeradorRecubierto Cómo hacer entrar el refrigerador en la casa Instrucciones DE InstalaciónDesempaque el refrigerador Cómo reducir el arco de vuelcoConexión a la línea de agua Piezas necesarias Cómo instalar los tableros antivuelcoConexión del suministro de agua Cómo instalar los tableros antivuelcoCm a 3,18 cm cercana al refrigerador Estilo 2-Conexión de la tubería de cobreConexión al refrigerador Piezas suministradasNivelación y alineamiento del refrigerador Cómo enchufar el refrigeradorCómo mover el refrigerador a su ubicación Final Paneles de la puerta Cómo instalar los paneles a la medida Para la serie ClassicInstalación del panel de la puerta Serie de paneles recubiertosModelos Classic y Architect Ajuste las puertasCómo ajustar la altura de la puerta Cómo ajustar la oscilación de las puertasCómo instalar la rejilla de la base Cómo instalar el panel lateralEstilo 2-Modelos sin despachador Cómo terminar la instalaciónPreparación del sistema de agua Estilo 1-Modelos con despachadorVotre sécurité et celle des autres est très importante Sécurité DU RéfrigérateurSérie Classic ModèlesRéfrigérateurs côte à côte sans distributeur Série ArchitectSérie Complète Réfrigérateurs côte à côte avec distributeurOutillage et pièces Exigences D’INSTALLATIONExigences d’emplacement Dimensions de l’ouvertureMéthode recommandée de mise à la terre Rayon de basculement Spécifications de l’alimentation en eauModèle Dimensions du produitVue latérale Vue avant Vue de dessusModèles de 48 121,9 cm Dimensions pour louverture des portesModèles de 36 91,4 cm Modèles de 42 106,7 cm Porte Porte Modèle a Panneau décoratif de la série Panneaux décoratifsPour retirer le cadre du distributeur Panneaux dappuiModèle D Ensembles de panneaux dorigine de la série Classic 34 ¹⁄₄ 87,0 cm Panneaux personnalisés de la série ClassicPanneaux de porte pour modèles sans distributeur Panneau de la grille supérieureLe cadre du distributeur se fixe au panneau avec 4 vis Panneaux de porte pour modèles avec distributeurPour retirer le cadre du distributeur Dimensions pour un panneau inséré en retrait Dimensions du réfrigérateur et des garnitures latéralesRéfrigérateur Dimensions pour un panneau inséré Dimensions pour un panneau en affleurementRéfrigérateur Instructions ’INSTALLATIONDéballage du réfrigérateur Saisir les deux extrémités de la grille supérieure Réduction du rayon de basculementFaire entrer le réfrigérateur dans le domicile Modèle Rayon de basculement réduitRaccordement à l’alimentation en eau Installation de planches antibasculementVérifier qu’il s’agit d’une canalisation d’eau froide Raccordement au réfrigérateurPièces fournies 25 cm à 3,18 cm à proximité du réfrigérateurRéglage de laplomb et alignement du Réfrigérateur Déplacementdu réfrigérateur à Lemplacement finalBranchement du réfrigérateur Panneaux de porte Installation des panneaux personnalisés De la série ClassicInstallation des panneaux de porte Modèles Classic et Architect Ajustement desportesAjustement de la hauteur des portes Ajustement de louverture des portesEmboîter la plinthe sur la grille de la base Installation du panneau latéralInstallation de la grille de la base Style 2 Modèles sans distributeur Achever l’installationPréparation du système d’eau Style 1 Modèles avec distributeurW10555563A

KSSC36FTS, KSSC42FTS, KSSC48FTS specifications

The KitchenAid KSSC48FTS, KSSC42FTS, and KSSC36FTS are premium built-in side-by-side refrigerators designed for modern kitchens. These models not only provide ample storage but also incorporate advanced technologies and distinctive features that cater to culinary enthusiasts and everyday users alike.

The KitchenAid KSSC48FTS is the largest of the trio, offering an impressive 48-inch width and a generous capacity that provides ample space for fresh and frozen foods. It features a sleek stainless steel exterior with a commercial-inspired design that brings a professional touch to any kitchen. One standout characteristic is its ExtendFresh Temperature Management System, which utilizes sophisticated sensors and a dual cooling system to maintain optimal temperatures in both the refrigerator and freezer compartments. This helps preserve the freshness of perishable foods longer.

The KSSC42FTS, with a 42-inch width, retains many of the premium features found in its larger counterpart while providing slightly less capacity. It also includes the ExtendFresh system and is equipped with a FreshChill Temperature-Controlled Drawer that offers adjustable temperature settings, perfect for storing delicate items like wines and cheeses. Additional features include a water filtration system that reduces contaminants, ensuring that every glass of water is pure and refreshing.

At the heart of the KitchenAid KSSC36FTS is its 36-inch design, tailored for kitchens where space is a concern without compromising performance and style. Like the other models, it features the ExtendFresh system, along with an innovative Preserva Food Care System that helps to manage humidity levels in the refrigerator, preventing food spoilage. Each model boasts adjustable spill-resistant shelves, enhancing organization and making cleanup easier.

In terms of usability, all three models come equipped with interior LED lighting, providing bright illumination to help you easily find what you need. The appliances also feature a user-friendly control panel that allows for precise temperature adjustments and settings.

The KitchenAid KSSC series is built not just for function but also for performance and convenience, providing users with a perfect blend of style, technology, and capacity. Whether you opt for the KSSC48FTS, KSSC42FTS, or KSSC36FTS, you’ll enjoy a premium refrigeration experience tailored to meet your kitchen needs.
Top Page Image Contents