Complete Installation

1.Turn the water supply line valve to the “Open” position.

2.Turn the refrigerator switch to the ON position. See “Power On/Off Switch” in the Use and Care Guide for instructions. Wait a few minutes. Check the water line connections for leaks.

3.Remove all boxes, parts packages and packing materials from the interior of the refrigerator. See the “Cleaning” section in the Use and Care Guide for instructions. Remove the film and cardboard from the grille and doors or door frame, depending on your model.

4.Install the shelves and bins in the refrigerator and freezer compartments.

5.The controls are preset at the factory to the midpoint setting. Make sure the compressor is operating properly and that all the lights are working.

6.Flush the water system before use. See “Water System Preparation.”

To get the most efficient use from your new built-in refrigerator, read the Use and Care Guide. Keep Installation Instructions and Use & Care Guide near the built-in refrigerator for easy reference.

Water System Preparation

Please read before using the water system. Follow the directions specific to your model.

Style 1 – Dispenser Models

IMPORTANT: After connecting the refrigerator to a water source or replacing the water filter, follow the steps below to make sure that the water system is properly cleaned. This will flush air from the filter and water dispensing system, and prepare the water filter for use.

The On/Off switch is located on the top right side of the freezer compartment.

1.Open the freezer door and turn off the ice maker. Move the switch to the OFF (right) setting as shown.

NOTE: If your model has a base grille filter system, make sure the base grille filter is properly installed and the cap is in the horizontal position.

Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.

2.Use a sturdy container to depress and hold the water dispenser lever for 5 seconds, then release it for 5 seconds. Repeat until water begins to flow. Once water begins to flow, continue depressing and releasing the dispenser lever

(5 seconds on, 5 seconds off) until a total of 3 gal. (12 L) has been dispensed. This will flush air from the filter and water dispensing system, and prepare the water filter for use. Additional flushing may be required in some households.

NOTE: As air is cleared from the system, water may spurt out of the dispenser.

3.Open the freezer door and turn on the ice maker. Move the switch to the ON (left) position.

■Allow 24 hours to produce the first batch of ice.

■Discard the first three batches of ice produced.

■Depending on your model, you may want to select the maximum ice feature to increase the production of ice.

Style 2 – Non-Dispenser Models

IMPORTANT: After connecting the refrigerator to a water source or replacing the water filter, fill and discard two full containers of ice to prepare the water filter for use, before using the ice.

1.Turn on the ice maker. Lower the wire shutoff arm as shown. Please refer to “Ice Maker and Storage Bin” for further instructions on the operation of your ice maker.

NOTES:

■Allow 24 hours to produce the first batch of ice.

■Allow 3 days to completely fill ice container.

■Depending on your model, you may want to select the maximum ice feature to increase the production of ice.

NOTE: If your model has a base grille filter system, make sure the base grille filter is properly installed and the cap is in the horizontal position.

KSSC36FTS, KSSC42FTS, KSSC48FTS specifications

The KitchenAid KSSC48FTS, KSSC42FTS, and KSSC36FTS are premium built-in side-by-side refrigerators designed for modern kitchens. These models not only provide ample storage but also incorporate advanced technologies and distinctive features that cater to culinary enthusiasts and everyday users alike.

The KitchenAid KSSC48FTS is the largest of the trio, offering an impressive 48-inch width and a generous capacity that provides ample space for fresh and frozen foods. It features a sleek stainless steel exterior with a commercial-inspired design that brings a professional touch to any kitchen. One standout characteristic is its ExtendFresh Temperature Management System, which utilizes sophisticated sensors and a dual cooling system to maintain optimal temperatures in both the refrigerator and freezer compartments. This helps preserve the freshness of perishable foods longer.

The KSSC42FTS, with a 42-inch width, retains many of the premium features found in its larger counterpart while providing slightly less capacity. It also includes the ExtendFresh system and is equipped with a FreshChill Temperature-Controlled Drawer that offers adjustable temperature settings, perfect for storing delicate items like wines and cheeses. Additional features include a water filtration system that reduces contaminants, ensuring that every glass of water is pure and refreshing.

At the heart of the KitchenAid KSSC36FTS is its 36-inch design, tailored for kitchens where space is a concern without compromising performance and style. Like the other models, it features the ExtendFresh system, along with an innovative Preserva Food Care System that helps to manage humidity levels in the refrigerator, preventing food spoilage. Each model boasts adjustable spill-resistant shelves, enhancing organization and making cleanup easier.

In terms of usability, all three models come equipped with interior LED lighting, providing bright illumination to help you easily find what you need. The appliances also feature a user-friendly control panel that allows for precise temperature adjustments and settings.

The KitchenAid KSSC series is built not just for function but also for performance and convenience, providing users with a perfect blend of style, technology, and capacity. Whether you opt for the KSSC48FTS, KSSC42FTS, or KSSC36FTS, you’ll enjoy a premium refrigeration experience tailored to meet your kitchen needs.