KitchenAid KSSC42FTS, KSSC48FTS, KSSC36FTS manual Install Side Panel, Install Base Grille

Page 26

Door-to-Door or Door-to-Refrigerator Trim Adjustment

1.Loosen, but do not remove, the four Torx®† 27 flat-head mounting screws and the two ¹⁄₄" hex-head mounting screws.

2.Adjust the top hinge of either door to align it with the other door or the refrigerator trim.

3.Tighten the four Torx®† 27 flat-head mounting screws to a torque of approximately 100 inch-pounds (11.3 Nm) and tighten the two ¹⁄₄" hex-head mounting screws.

A

B

A. Torx® 27 flat-head mounting screws

B. ¹⁄₄" hex-head mounting screws

Install Side Panel

If the built-in area depth is 25" (63.5 cm) or more, the side panels can be installed inside the side trim or attached to the outside of the side trim.

IMPORTANT: KitchenAid is not responsible for the removal or addition of molding or decorative panels that would not allow access to the refrigerator for service.

1.For the inside side trim piece, slide the front edge of the routed side panel into the trim piece.

2.Nail the rear edge of the panel to the support board.

A

B

A. Support board (mounted to back wall)

B. Cab side trim

†®TORX is a registered trademark of Saturn Fasteners, Inc.

Install Base Grille

There are two pieces to the base grille to allow for a custom fit: the base grille itself and the skirt. The skirt can be added to the base grille in order to extend it all the way to the floor.

1.To see whether the skirt is needed, place the base grille into position. Do not attach the base grille to the refrigerator. Measure the distance between the bottom of the base grille and the floor. The gap must be a minimum of ¹⁄₂" (1.27 cm) in order to add the skirt.

NOTE: If the gap measures less than ¹⁄₂" (1.27 cm), skip steps 3 and 4 of the instructions, and install the base grille only.

2.Remove the film from the base grille.

3.Snap the skirt onto the base grille.

A

B

A. Base grille

B.Skirt

4.Trim the skirt by scoring the proper “V” groove with a utility knife. Break the skirt at the score line.

A

A. “V” groove

5.Using the two screws, attach the base grille assembly to the refrigerator as shown.

NOTE: Drive in the right side screw first.

A

A. Screws (2)

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Table of Contents/Índice/Table des matières Side by Side BUILT-IN RefrigeratorTable DES Matières Table of ContentsÍndice Refrigerator Safety Your safety and the safety of others are very importantArchitect Series ModelsSide by Side Non-Dispensing Refrigerators Classic SeriesSide by Side Dispensing Refrigerators Complete SeriesLocation Requirements Installation RequirementsTools and Parts Electrical Requirements Recommended Grounding MethodWater Supply Requirements Tipping RadiusTop View Product DimensionsSide View Front View Model42 106.7 cm Models Door Swing Dimensions36 91.4 cm Models 48 121.9 cm ModelsDoor Overlay Series Door Panel and CabinetryClearanceHinge Model a Overlay Series Custom Panels and Handle KitsDecorative Overlay Panel Model D Backer PanelsDispenser Frame dispenser models only Dispenser frame attaches to the panel with 4 screwsClassic Series Factory Panels and Kits Top Grille Panel Classic Series Custom PanelsDoor Panels for Non-dispenser Models To remove the dispenser frame Door Panels for Dispenser ModelsDispenser Frame Classic series dispenser models Classic, Architect and Complete Series Custom Side Panels Overlay Series Custom Side PanelsMeasure the distance from point a as shown to back wall Installation InstructionsUnpack the Refrigerator Reduce Tipping Radius Install Anti-Tip BoardsTo Install Anti-tip Boards Move the Refrigerator into HouseStyle 1-Shutoff Valve Connection Connect the Water SupplyConnect to Water Line Parts Needed Style 2-Copper Line ConnectionParts Supplied Plug in RefrigeratorMove Refrigerator to Final Location Connect to RefrigeratorDoor Panels Install Classic Series Custom PanelsLevel and Align Refrigerator Check refrigerator level and adjustment. Adjust if needed Install Overlay Series Custom PanelsDoor Panel Installation Door Swing Adjustment Adjust DoorsDoor Height Adjustment Classic and Architect ModelsDoor-to-Door or Door-to-Refrigerator Trim Adjustment Install Side PanelInstall Base Grille Style 1 Dispenser Models Complete InstallationWater System Preparation Style 2 Non-Dispenser ModelsSeguridad DEL Refrigerador Su seguridad y la seguridad de los demás es muy importanteSerie Architect ModelosRefrigeradores de dos puertas sin despachador Serie ClassicRefrigeradores de dos puertas con despachador Serie CompleteRequisitos de ubicación Requisitos DE InstalaciónPiezas y herramientas Medidas de la aberturaMétodo de conexión a tierra recomendado Requisitos del suministro de agua Arco de vuelcoMedidas del producto Modelos de 48 121,9 cm Medidas de oscilación de las puertasModelos de 36 91,4 cm Modelos de 42 106,7 cm Panel Oscilación de Panel decorativo recubierto Modelo aModelo D Paneles de soporteMarco del despachador Solamente en modelos con despachador El marco del despachador se sujeta al panel con 4 tornillosPaneles y juegos de fábrica de la serie Classic Panel de la rejilla superior Panelesa la medida para la serie ClassicPaneles de puerta para modelos sin despachador ModeloPaneles de puerta para modelos con despachador Refrigerador Medidas para la instalación empotradaMedidas del refrigerador y del adorno lateral Adorno lateralRecubierto Cómo reducir el arco de vuelco Instrucciones DE InstalaciónDesempaque el refrigerador Cómo hacer entrar el refrigerador en la casaCómo instalar los tableros antivuelco Cómo instalar los tableros antivuelcoConexión del suministro de agua Conexión a la línea de agua Piezas necesariasPiezas suministradas Estilo 2-Conexión de la tubería de cobreConexión al refrigerador Cm a 3,18 cm cercana al refrigeradorNivelación y alineamiento del refrigerador Cómo enchufar el refrigeradorCómo mover el refrigerador a su ubicación Final Cómo instalar los paneles a la medida Para la serie Classic Paneles de la puertaSerie de paneles recubiertos Instalación del panel de la puertaCómo ajustar la oscilación de las puertas Ajuste las puertasCómo ajustar la altura de la puerta Modelos Classic y ArchitectCómo instalar el panel lateral Cómo instalar la rejilla de la baseEstilo 1-Modelos con despachador Cómo terminar la instalaciónPreparación del sistema de agua Estilo 2-Modelos sin despachadorSécurité DU Réfrigérateur Votre sécurité et celle des autres est très importanteSérie Architect ModèlesRéfrigérateurs côte à côte sans distributeur Série ClassicRéfrigérateurs côte à côte avec distributeur Série ComplèteDimensions de l’ouverture Exigences D’INSTALLATIONExigences d’emplacement Outillage et piècesMéthode recommandée de mise à la terre Spécifications de l’alimentation en eau Rayon de basculementVue de dessus Dimensions du produitVue latérale Vue avant ModèleModèles de 48 121,9 cm Dimensions pour louverture des portesModèles de 36 91,4 cm Modèles de 42 106,7 cm Porte Porte Panneau décoratif de la série Panneaux décoratifs Modèle aPour retirer le cadre du distributeur Panneaux dappuiModèle D Ensembles de panneaux dorigine de la série Classic Panneau de la grille supérieure Panneaux personnalisés de la série ClassicPanneaux de porte pour modèles sans distributeur 34 ¹⁄₄ 87,0 cmLe cadre du distributeur se fixe au panneau avec 4 vis Panneaux de porte pour modèles avec distributeurPour retirer le cadre du distributeur Dimensions pour un panneau en affleurement Dimensions du réfrigérateur et des garnitures latéralesRéfrigérateur Dimensions pour un panneau inséré Dimensions pour un panneau inséré en retraitRéfrigérateur Instructions ’INSTALLATIONDéballage du réfrigérateur Modèle Rayon de basculement réduit Réduction du rayon de basculementFaire entrer le réfrigérateur dans le domicile Saisir les deux extrémités de la grille supérieureInstallation de planches antibasculement Raccordement à l’alimentation en eau25 cm à 3,18 cm à proximité du réfrigérateur Raccordement au réfrigérateurPièces fournies Vérifier qu’il s’agit d’une canalisation d’eau froideRéglage de laplomb et alignement du Réfrigérateur Déplacementdu réfrigérateur à Lemplacement finalBranchement du réfrigérateur Installation des panneaux personnalisés De la série Classic Panneaux de porteInstallation des panneaux de porte Ajustement de louverture des portes Ajustement desportesAjustement de la hauteur des portes Modèles Classic et ArchitectEmboîter la plinthe sur la grille de la base Installation du panneau latéralInstallation de la grille de la base Style 1 Modèles avec distributeur Achever l’installationPréparation du système d’eau Style 2 Modèles sans distributeurW10555563A

KSSC36FTS, KSSC42FTS, KSSC48FTS specifications

The KitchenAid KSSC48FTS, KSSC42FTS, and KSSC36FTS are premium built-in side-by-side refrigerators designed for modern kitchens. These models not only provide ample storage but also incorporate advanced technologies and distinctive features that cater to culinary enthusiasts and everyday users alike.

The KitchenAid KSSC48FTS is the largest of the trio, offering an impressive 48-inch width and a generous capacity that provides ample space for fresh and frozen foods. It features a sleek stainless steel exterior with a commercial-inspired design that brings a professional touch to any kitchen. One standout characteristic is its ExtendFresh Temperature Management System, which utilizes sophisticated sensors and a dual cooling system to maintain optimal temperatures in both the refrigerator and freezer compartments. This helps preserve the freshness of perishable foods longer.

The KSSC42FTS, with a 42-inch width, retains many of the premium features found in its larger counterpart while providing slightly less capacity. It also includes the ExtendFresh system and is equipped with a FreshChill Temperature-Controlled Drawer that offers adjustable temperature settings, perfect for storing delicate items like wines and cheeses. Additional features include a water filtration system that reduces contaminants, ensuring that every glass of water is pure and refreshing.

At the heart of the KitchenAid KSSC36FTS is its 36-inch design, tailored for kitchens where space is a concern without compromising performance and style. Like the other models, it features the ExtendFresh system, along with an innovative Preserva Food Care System that helps to manage humidity levels in the refrigerator, preventing food spoilage. Each model boasts adjustable spill-resistant shelves, enhancing organization and making cleanup easier.

In terms of usability, all three models come equipped with interior LED lighting, providing bright illumination to help you easily find what you need. The appliances also feature a user-friendly control panel that allows for precise temperature adjustments and settings.

The KitchenAid KSSC series is built not just for function but also for performance and convenience, providing users with a perfect blend of style, technology, and capacity. Whether you opt for the KSSC48FTS, KSSC42FTS, or KSSC36FTS, you’ll enjoy a premium refrigeration experience tailored to meet your kitchen needs.
Top Page Image Contents