KitchenAid 2316565C manual Installation Requirements, Tools and Parts, Location Requirements

Page 6

INSTALLATION REQUIREMENTS

Tools and Parts

IMPORTANT:

Installer: Leave Installation Instructions with the homeowner.

Homeowner: Keep Installation Instructions for future reference. Save these Installation Instructions for the local electrical inspector’s use.

TOOLS NEEDED:

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

Cordless drill

Torx®†T27 screwdriver

Drill bits

¹¹⁄₃₂" nut driver

Two adjustable

³⁄₈" and ¹⁄₂" open-end wrenches

 

wrenches

⁵⁄₃₂" Allen wrench

 

Phillips screwdriver

¹⁄₄" and ⁵⁄₁₆" socket drivers

 

Small level

Tape measure

 

Appliance dolly

Utility knife

 

 

PARTS NEEDED:

Six #8 x 3" (7.6 cm) wood screws (longer screws may be needed)

One or two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) wood board(s)

Order factory panels, make custom panels or consult a qualified cabinetmaker or carpenter to make the panels.

Classic Series: Order factory panels, make custom panels, or consult a qualified cabinetmaker or carpenter to make the panels. See “Classic Series Custom Panels” for more information.

Overlay Series: Make custom panels, or consult a qualified cabinetmaker or carpenter to make the panels. See “Overlay Series Custom Panels and Handle Kits” for more information.

Architect® and Complete Series are shipped complete.

If you are connecting the water line directly to copper tubing and not to a shutoff valve, you need a ferrule, a union, and a ¹⁄₄" (6.35 mm) compression fitting.

Location Requirements

The refrigerator can be recessed in an opening between cabinets or installed at the end of a cabinet run using a side panel to enclose the refrigerator.

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

IMPORTANT:

Observe all governing codes and ordinances.

It is recommended that you do not install the refrigerator near an oven, radiator, or other heat source.

Do not install in a location where the temperature will fall below 55°F (13°C).

Floor must support the refrigerator weight, more than 600 lbs (272 kg), door panels and contents of the refrigerator.

Ceiling height must allow for side tipping radius. See “Tipping Radius.”

Location should permit door to open fully. See “Door Swing Dimensions.”

Location must permit top grille removal. See “Opening Dimensions.”

Opening Dimensions

To avoid tipping during use, the solid soffit must be within 1" (2.5 cm) maximum above the refrigerator. If the solid soffit is higher than 1" (2.5 cm) or one is not available, then the refrigerator must be braced.

If the anti-tip boards are needed, they must be attached to the rear wall studs 80" to 90" (203 cm to 229 cm) above the floor. See “Install Anti-Tip Boards” for more information.

NOTE: A clearance of ¹⁄₂" (1.3 cm) must be maintained above the top grille in order for the top grille to be removed.

¹⁄₂"

(1.3 cm)

†®TORX is a registered trademark of Textron Innovations Inc.

6

Image 6
Contents Table of Contents/Índice/Table des matières Side by Side BUILT-IN RefrigeratorTable of Contents ÍndiceTable DES Matières Refrigerator Safety Your safety and the safety of others are very importantArchitect Series ModelsSide by Side Non-Dispensing Refrigerators Classic SeriesSide by Side Dispensing Refrigerators Complete SeriesTools and Parts Installation RequirementsOpening Dimensions Location RequirementsElectrical Requirements Recommended Grounding MethodModel Width a as shown above Water Pressure Water Supply RequirementsTipping Radius Reverse Osmosis Water SupplyTop View Front View Product DimensionsSide View Model Width a Trim edge to trim edge42 106.7 cm Models Door Swing Dimensions36 91.4 cm Models 48 121.9 cm ModelsOverlay Panel Overlay Series Door Panel & Cabinetry Clearance90˚ Door Stop Position Hinge Model Overlay Series Custom Panels and Handle KitsDecorative Overlay Panel 34³/₄ 88.27 cmBacker Panels Dispenser Frame dispenser models onlyTo remove the dispenser frame Classic Series Factory Panels and Kits Door Panels for Dispenser Models Classic Series Custom PanelsTop Grille Panel Door Panels for Non-dispenser ModelsClassic, Architect and Complete Series Custom Side Panels Overlay Series Custom Side Panels Flush Installation DimensionsRecessed Inset Installation Dimensions Measure the distance from point a as shown to the back wallReduce Tipping Radius Installation InstructionsUnpack the Refrigerator Move the Refrigerator into HouseStyle 2 Copper Line Connection Connecting to Water Line Install Anti-Tip BoardsTo Install Anti-tip Boards Connect the Water SupplyConnecting to Refrigerator Plug in RefrigeratorMove Refrigerator to Final Location Install Classic Series Custom Panels Level and Align RefrigeratorDoor Panels Check refrigerator level and adjustment. Adjust if needed Install Overlay Series Custom PanelsDoor Panel Installation Reinstall the handle-side and top trimsDoor Swing Adjustment Adjust DoorsDoor Height Adjustment Classic and Architect ModelsInstall Base Grille Install Side PanelDoor-to-Door or Door-to-Refrigerator Trim Adjustment Turn the water supply line valve to the Open position Complete InstallationWater System Preparation Style 1 Non-Dispenser Models Style 2 Dispenser ModelsSeguridad DEL Refrigerador Su seguridad y la seguridad de los demás es muy importanteSerie II Architect ModelosRefrigeradores de dos puertas sin despachador Serie ClassicRefrigeradores de dos puertas con despachador Serie CompleteRequisitos de ubicación Requisitos DE InstalaciónPiezas y herramientas Medidas de la aberturaRequisitos eléctricos Método de conexión a tierra recomendadoModelo Ancho a Como se muestra anteriormente Presión del agua Requisitos del suministro de aguaArco de vuelco Suministro de agua de ósmosis inversaVista superior Medidas del productoVista lateral Vista frontalModelos de 42 106,7 cm Medidas de oscilación de las puertasModelos de 36 91,4 cm Modelos de 48 121,9 cmPuerta Recubierto Modelo Paneles a la medida y juegos de manijas de la serie OverlayPanel decorativo con revestimiento 34³/₄ 88,27 cmNotas Paneles de soporteMarco del despachador solamente en modelos con despachador Para quitar el marco del despachadorPaneles y juegos de fábrica de la Serie Classic Panel de la rejilla superior Paneles a la medida para la serie ClassicPaneles de puerta para modelos sin despachador Modelo 34 ¹⁄₄ 87,0 cm 40 ¹⁄₄ 102,2 cm 46 ¹⁄₄ 117,5 cmPaneles de puerta para modelos con despachador Paneles laterales a la medida para la Serie Overlay Instrucciones DE Instalación Desempaque el refrigeradorCómo instalar los tableros antivuelco Cómo reducir el arco de vuelcoCómo hacer entrar el refrigerador en la casa Cómo instalar los tableros antivuelcoLea todas las instrucciones antes de comenzar Conexión del suministro de aguaEstilo 1 Conexión de la válvula de cierre Abra la válvula de cierreNivelación y alineamiento del refrigerador Cómo enchufar el refrigeradorCómo mover el refrigerador a su Ubicación final Conexión al refrigeradorCómo instalar los paneles a la medida para La serie Classic Paneles de la puertaCómo instalar los paneles a la medida para La serie Overlay Instalación del panel de la puertaCómo ajustar la oscilación de las puertas Ajuste las puertasCómo ajustar la altura de la puerta Modelos Classic y ArchitectCómo instalar el panel lateral Cómo instalar la rejilla de la baseEncaje a presión el faldón sobre la rejilla de la base Cómo terminar la instalación Preparación del sistema de aguaSécurité DU Réfrigérateur Votre sécurité et celle des autres est très importanteSérie II Architect ModèlesRéfrigérateurs côte à côte sans distributeur Série ClassicRéfrigérateurs côte à côte avec distributeur Série CompleteDimensions de l’ouverture Exigences D’INSTALLATIONExigences d’emplacement Outillage et piècesMéthode recommandée de mise à la terre Spécifications électriquesModèle Largeur a tel quillustré ci-dessus Pression de leau Spécifications de l’alimentation en eauRayon de basculement Alimentation en eau par osmose inverseVue de dessus Vue avant Dimensions du produitVue latérale Modèle Largeur a ’un bord à l’autre De la garnitureModèles de 42 106,7 cm Dimensions pour le pivotement des portesModèles de 36 91,4 cm Modèles de 48 121,9 cmPorte Charnière Porte Panneaux personnalisés et poignées de la série Overlay Panneau de recouvrementModèle 39³/₄ 100,97 cm Panneaux dappuiRemarques 45³/₄ 116,21 cmEnsembles de panneaux dorigine de la Série Classic Panneaux de porte pour modèles sans distributeur Remarque Les dimensions indiquées ont une tolérance dePanneaux personnalisés de la série Classic Panneau de la grille supérieurePanneaux de porte pour modèles avec distributeur Panneaux latéraux personnalisés de la Série Overlay Instructions D’INSTALLATION Déballage du réfrigérateurRéduction du rayon de basculement Installation de planches antibasculementInstallation des planches antibasculement Faire entrer le réfrigérateur dans le domicileRaccordement à la canalisation deau Style 1 Raccordement sur robinet darrêtRéglage de laplomb et alignement du Réfrigérateur Déplacement du réfrigérateur à Lemplacement finalBrancher le réfrigérateur Raccordement au réfrigérateurInstallation des panneaux personnalisés De la série Classic Panneaux de porteInstallation des panneaux personnalisés De la série Overlay Installation des panneaux de porteAjustement du pivotement des portes Ajustement des portesAjustement de la hauteur des portes Modèles Classic et ArchitectInstallation du panneau latéral Installation de la grille de la baseVeuillez lire avant d’utiliser le système d’eau Achever l’installationPréparation du système d’eau 2316565C

2316565C specifications

The KitchenAid 2316565C is a versatile and innovative blending tool designed for culinary enthusiasts who appreciate both quality and performance in their kitchen appliances. This model stands out due to its powerful motor and unique features that enhance the cooking experience.

One of the main features of the KitchenAid 2316565C is its robust 3.5 horsepower motor, which ensures efficient blending even with the toughest ingredients. Whether you're making smoothies, soups, or sauces, this blender can effortlessly handle ice and frozen fruits, delivering a smooth and consistent texture every time.

The unit's stainless-steel blades are engineered for durability and precision. Their unique design helps to create a vortex that pulls ingredients down toward the blades for even blending. This technology allows for superior blending performance, reducing the preparation time for various recipes.

The KitchenAid 2316565C also comes with a large capacity blending jar that accommodates up to 64 ounces. This generous size is perfect for family meals or entertaining guests, enabling you to blend large batches without needing to refill. Additionally, the jar features measurement markings, allowing for precise ingredient additions and recipe adjustments on the fly.

Another key feature of this blender is its intuitive control panel, which includes multiple speed settings and a pulse function. Users can easily customize blending speeds to achieve the desired consistency, whether it’s a silky smooth puree or a chunky salsa. The pulse function adds versatility, making it simple to chop or mix ingredients without over-blending.

Safety is a priority with the KitchenAid 2316565C. The blender includes a safety lock mechanism that prevents operation unless the lid is securely in place. This feature provides peace of mind, especially when blending hot ingredients, ensuring that spills and splatters are minimized.

Finally, the appliance's sleek and modern design seamlessly fits into any kitchen decor, while its easy-to-clean removable parts make it a practical choice for daily use. The blender is dishwasher-safe, allowing for hassle-free clean-up after meal prep.

In summary, the KitchenAid 2316565C is a powerful and efficient blender that combines performance, safety, and style. It is ideal for users seeking to elevate their culinary creations with ease, making it a worthy addition to any kitchen.