KitchenAid 2316565C manual Electrical Requirements, Recommended Grounding Method

Page 7

A grounded 3 prong electrical outlet should be placed within 4" (10.2 cm) of the right side cabinets or end panel. See “Electrical Requirements” for more information.

The water shutoff should be located in the base cabinet on either side of the refrigerator or some other easily accessible area. If the water shutoff valve is not in the cabinets, the plumbing for the water line can come through the floor or the back wall. See “Water Supply Requirements” for more information.

 

80" - 90"

 

 

(203-229 cm)

4"

 

 

 

 

(10.2 cm)

83¹⁄₂" (212.1 cm) min.

 

84³⁄₄" (215 cm) max.

 

to bottom of solid soffit

 

 

 

77"

 

 

(196 cm)

 

A

 

 

Width

 

 

(see chart following)

 

 

 

6"

 

 

(15.2 cm)

 

1"

 

6"

(2.54 cm)

6"

(15.2 cm)

(15.2 cm)

 

24"

 

 

(60.96 cm) min.

 

Model Width A (as shown above)

3635¹⁄₂" (90.2 cm) to 35³⁄₄" (90.8 cm)

4241¹⁄₂" (105.4 cm) to 41³⁄₄" (106.1 cm)

4847¹⁄₂" (120.7 cm) to 47³⁄₄" (121.3 cm)

NOTE: Flooring under refrigerator must be at same level as the room. Face of cabinetry must be plumb.

Electrical Requirements

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115 Volt, 60 Hz., AC only, 15- or 20-amp fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet that cannot be turned off by a switch. Do not use an extension cord.

IMPORTANT: If this product is connected to a GFCI (Ground Fault Circuit Interrupter) protected outlet, nuisance tripping of the power supply may occur, resulting in loss of cooling. Food quality and flavor may be affected. If nuisance tripping has occurred, and if the condition of the food appears poor, dispose of it.

NOTE: Before performing any type of installation, cleaning, or removing a light bulb, remove the top grille and turn the master power switch to OFF or disconnect power at the circuit breaker box.

When you are finished, turn ON the master power switch or reconnect power at the circuit breaker box. Then reset the control to the desired setting.

7

Image 7
Contents Side by Side BUILT-IN Refrigerator Table of Contents/Índice/Table des matièresÍndice Table of ContentsTable DES Matières Your safety and the safety of others are very important Refrigerator SafetyClassic Series ModelsSide by Side Non-Dispensing Refrigerators Architect SeriesComplete Series Side by Side Dispensing RefrigeratorsLocation Requirements Installation RequirementsOpening Dimensions Tools and PartsRecommended Grounding Method Electrical RequirementsModel Width a as shown above Reverse Osmosis Water Supply Water Supply RequirementsTipping Radius Water PressureModel Width a Trim edge to trim edge Product DimensionsSide View Top View Front View48 121.9 cm Models Door Swing Dimensions36 91.4 cm Models 42 106.7 cm ModelsOverlay Series Door Panel & Cabinetry Clearance Overlay Panel90˚ Door Stop Position Hinge 34³/₄ 88.27 cm Overlay Series Custom Panels and Handle KitsDecorative Overlay Panel ModelDispenser Frame dispenser models only Backer PanelsTo remove the dispenser frame Classic Series Factory Panels and Kits Door Panels for Non-dispenser Models Classic Series Custom PanelsTop Grille Panel Door Panels for Dispenser ModelsClassic, Architect and Complete Series Custom Side Panels Measure the distance from point a as shown to the back wall Flush Installation DimensionsRecessed Inset Installation Dimensions Overlay Series Custom Side PanelsMove the Refrigerator into House Installation InstructionsUnpack the Refrigerator Reduce Tipping RadiusConnect the Water Supply Install Anti-Tip BoardsTo Install Anti-tip Boards Style 2 Copper Line Connection Connecting to Water LinePlug in Refrigerator Connecting to RefrigeratorMove Refrigerator to Final Location Level and Align Refrigerator Install Classic Series Custom PanelsDoor Panels Reinstall the handle-side and top trims Install Overlay Series Custom PanelsDoor Panel Installation Check refrigerator level and adjustment. Adjust if neededClassic and Architect Models Adjust DoorsDoor Height Adjustment Door Swing AdjustmentInstall Side Panel Install Base GrilleDoor-to-Door or Door-to-Refrigerator Trim Adjustment Style 1 Non-Dispenser Models Style 2 Dispenser Models Complete InstallationWater System Preparation Turn the water supply line valve to the Open positionSu seguridad y la seguridad de los demás es muy importante Seguridad DEL RefrigeradorSerie Classic ModelosRefrigeradores de dos puertas sin despachador Serie II ArchitectSerie Complete Refrigeradores de dos puertas con despachadorMedidas de la abertura Requisitos DE InstalaciónPiezas y herramientas Requisitos de ubicaciónMétodo de conexión a tierra recomendado Requisitos eléctricosModelo Ancho a Como se muestra anteriormente Suministro de agua de ósmosis inversa Requisitos del suministro de aguaArco de vuelco Presión del aguaVista frontal Medidas del productoVista lateral Vista superiorModelos de 48 121,9 cm Medidas de oscilación de las puertasModelos de 36 91,4 cm Modelos de 42 106,7 cmPuerta Recubierto 34³/₄ 88,27 cm Paneles a la medida y juegos de manijas de la serie OverlayPanel decorativo con revestimiento ModeloPara quitar el marco del despachador Paneles de soporteMarco del despachador solamente en modelos con despachador NotasPaneles y juegos de fábrica de la Serie Classic Modelo 34 ¹⁄₄ 87,0 cm 40 ¹⁄₄ 102,2 cm 46 ¹⁄₄ 117,5 cm Paneles a la medida para la serie ClassicPaneles de puerta para modelos sin despachador Panel de la rejilla superiorPaneles de puerta para modelos con despachador Paneles laterales a la medida para la Serie Overlay Desempaque el refrigerador Instrucciones DE InstalaciónCómo instalar los tableros antivuelco Cómo reducir el arco de vuelcoCómo hacer entrar el refrigerador en la casa Cómo instalar los tableros antivuelcoAbra la válvula de cierre Conexión del suministro de aguaEstilo 1 Conexión de la válvula de cierre Lea todas las instrucciones antes de comenzarConexión al refrigerador Cómo enchufar el refrigeradorCómo mover el refrigerador a su Ubicación final Nivelación y alineamiento del refrigeradorPaneles de la puerta Cómo instalar los paneles a la medida para La serie ClassicInstalación del panel de la puerta Cómo instalar los paneles a la medida para La serie OverlayModelos Classic y Architect Ajuste las puertasCómo ajustar la altura de la puerta Cómo ajustar la oscilación de las puertasCómo instalar la rejilla de la base Cómo instalar el panel lateralEncaje a presión el faldón sobre la rejilla de la base Preparación del sistema de agua Cómo terminar la instalaciónVotre sécurité et celle des autres est très importante Sécurité DU RéfrigérateurSérie Classic ModèlesRéfrigérateurs côte à côte sans distributeur Série II ArchitectSérie Complete Réfrigérateurs côte à côte avec distributeurOutillage et pièces Exigences D’INSTALLATIONExigences d’emplacement Dimensions de l’ouvertureSpécifications électriques Méthode recommandée de mise à la terreModèle Largeur a tel quillustré ci-dessus Alimentation en eau par osmose inverse Spécifications de l’alimentation en eauRayon de basculement Pression de leauModèle Largeur a ’un bord à l’autre De la garniture Dimensions du produitVue latérale Vue de dessus Vue avantModèles de 48 121,9 cm Dimensions pour le pivotement des portesModèles de 36 91,4 cm Modèles de 42 106,7 cmPorte Charnière Porte Panneau de recouvrement Panneaux personnalisés et poignées de la série OverlayModèle 45³/₄ 116,21 cm Panneaux dappuiRemarques 39³/₄ 100,97 cmEnsembles de panneaux dorigine de la Série Classic Panneau de la grille supérieure Remarque Les dimensions indiquées ont une tolérance dePanneaux personnalisés de la série Classic Panneaux de porte pour modèles sans distributeurPanneaux de porte pour modèles avec distributeur Panneaux latéraux personnalisés de la Série Overlay Déballage du réfrigérateur Instructions D’INSTALLATIONFaire entrer le réfrigérateur dans le domicile Installation de planches antibasculementInstallation des planches antibasculement Réduction du rayon de basculementStyle 1 Raccordement sur robinet darrêt Raccordement à la canalisation deauRaccordement au réfrigérateur Déplacement du réfrigérateur à Lemplacement finalBrancher le réfrigérateur Réglage de laplomb et alignement du RéfrigérateurPanneaux de porte Installation des panneaux personnalisés De la série ClassicInstallation des panneaux de porte Installation des panneaux personnalisés De la série OverlayModèles Classic et Architect Ajustement des portesAjustement de la hauteur des portes Ajustement du pivotement des portesInstallation de la grille de la base Installation du panneau latéral2316565C Achever l’installationPréparation du système d’eau Veuillez lire avant d’utiliser le système d’eau

2316565C specifications

The KitchenAid 2316565C is a versatile and innovative blending tool designed for culinary enthusiasts who appreciate both quality and performance in their kitchen appliances. This model stands out due to its powerful motor and unique features that enhance the cooking experience.

One of the main features of the KitchenAid 2316565C is its robust 3.5 horsepower motor, which ensures efficient blending even with the toughest ingredients. Whether you're making smoothies, soups, or sauces, this blender can effortlessly handle ice and frozen fruits, delivering a smooth and consistent texture every time.

The unit's stainless-steel blades are engineered for durability and precision. Their unique design helps to create a vortex that pulls ingredients down toward the blades for even blending. This technology allows for superior blending performance, reducing the preparation time for various recipes.

The KitchenAid 2316565C also comes with a large capacity blending jar that accommodates up to 64 ounces. This generous size is perfect for family meals or entertaining guests, enabling you to blend large batches without needing to refill. Additionally, the jar features measurement markings, allowing for precise ingredient additions and recipe adjustments on the fly.

Another key feature of this blender is its intuitive control panel, which includes multiple speed settings and a pulse function. Users can easily customize blending speeds to achieve the desired consistency, whether it’s a silky smooth puree or a chunky salsa. The pulse function adds versatility, making it simple to chop or mix ingredients without over-blending.

Safety is a priority with the KitchenAid 2316565C. The blender includes a safety lock mechanism that prevents operation unless the lid is securely in place. This feature provides peace of mind, especially when blending hot ingredients, ensuring that spills and splatters are minimized.

Finally, the appliance's sleek and modern design seamlessly fits into any kitchen decor, while its easy-to-clean removable parts make it a practical choice for daily use. The blender is dishwasher-safe, allowing for hassle-free clean-up after meal prep.

In summary, the KitchenAid 2316565C is a powerful and efficient blender that combines performance, safety, and style. It is ideal for users seeking to elevate their culinary creations with ease, making it a worthy addition to any kitchen.