KitchenAid W10268948C installation instructions Range Hood USE, Complete Installation

Page 11

For non-vented (recirculating) installations only

4.Snap vent grids into openings in lower chimney.

BA

Complete Installation

1.Replace grease filters. See the “Range Hood Care” section.

2.Check the operation of the range hood fan and light. See “Range Hood Use” section.

If range hood does not operate, check to see whether a circuit breaker has tripped or a household fuse has blown. Disconnect power and check wiring connections.

NOTE: To get the most efficient use from your new range hood, read the “Range Hood Use” section.

A. 2 mounting screws

B. Vent grids (for non-vented installations)

RANGE HOOD USE

The range hood is designed to remove smoke, cooking vapors and odors from the cooktop area. For best results, start the hood before cooking and allow it to operate several minutes after the cooking is complete to clear all smoke and odors from the kitchen.

Control Panel

The range hood controls are located on the right-hand front surface of the range hood.

A

B

C

D

E

F

G

A. Fan motor on/off

 

 

E. 10 minute timed boost

B. Decrease fan motor speed

 

F. Light

 

 

C. Increase fan motor speed

 

G. Night light

 

D. Electronic display

 

 

 

 

 

Operating the Light

1.Press the light button (F) to turn on the light.

2.Press the light button (F) to turn off the light.

Operating the Fan and Adjusting Fan Speed

The fan has 4 speeds: 1 (low), 2 (medium), 3 (medium-high), and 4 (high).

1.Press the On/Off button (A) to turn the fan on. The speed setting will appear in the display.

2.Press the “plus” (+) or “minus” (-) buttons to increase or decrease the fan speed.

3.Press the On/Off button (A) to turn off the fan.

10-Minute Boost Function

Press the “H” button to start the 10-minute boost function. The fan motor will run on its highest speed (4) as the display counts down from 10 minutes. At the end of 10 minutes, the fan will return to the previously selected speed.

Reset Filter Alert

After 100 hours of use, “C” will appear in the range hood display. This “C” indicates that the filter must be cleaned. ”C” will appear only when turning off the range hood fan.

Reset Alarm Display

1.Turn off the range hood fan and light.

2.Press the “plus” (+) button for 4 seconds. The “C” will disappear from the display, and the counter will reset to “0.”

Operating the Night Light

1.Press the night light button (G) to turn on the night light.

2.Press the night light button (G) to turn off the night light.

Thermal Protector

The range hood is equipped with a thermal protector to avoid overheating conditions. If the range hood shuts off while in use, press the on/off button to turn off the range hood. Wait approximately 60 minutes, then press the on/off button to restart the range hood.

11

Image 11
Contents Canopy Hood Table DES Matières Table of ContentsYour safety and the safety of others are very important Range Hood SafetyImportant Safety Instructions Location Requirements Installation RequirementsToolsandParts Makeup air Installation DimensionsCold weather installations VentingRequirementsCalculating Vent System Length For non-vented recirculating installationsElectrical Requirements Rear dischargePrepareLocation Installation InstructionsRange Hood Mounting Screws Installation Chimney Support Bracket InstallationMake Electrical Connection InstallRange HoodVented Installations Non-vented recirculating InstallationsInstall Lower Chimney Cover Install Chimney CoversFor Vented Installations Install Upper Chimney CoverRange Hood USE Complete InstallationRange Hood Care CleaningWiring Diagram InCanada Assistance or ServiceAccessories IntheU.S.AThis limited warranty does not cover Kitchenaid Ventilation WarrantyPage Votre sécurité et celle des autres est très importante Sécurité DE LA Hotte DE CuisinièreImportantes Instructions DE Sécurité Outillageetpièces Exigences DinstallationExigences demplacement Installations sans décharge à lextérieur recyclage Dimensions du produitDimensions à respecter lors de linstallation Installations avec décharge à lextérieurExigences concernant lévacuation Composant Conduit de diamètre 15,2 cm Coude à SpécificationsélectriquesCalcul de la longueur effective du circuit dévacuation Exemple de système de déchargeInstallation de la bride de support de la cheminée Instructions DinstallationPréparationdelemplacement Installation des vis de montage de la hotteAchever la préparation Installationdela hotteInstallations avec décharge à lextérieur Installations sans décharge à lextérieur recyclageRaccordementélectrique Installation de la section inférieure du cache-cheminée Installationducache-cheminéeAcheverl’installation Installation de la section supérieure du cache-cheminéeNettoyage Utilisation DE LA HotteEntretien DE LA Hotte Remplacement dune lampe à halogène Réinstallation des filtres à graisse métalliquesInstallation des filtres à charbon Remplacement des filtres à charbonSchéma DE Câblage Accessoires Assistance OU ServiceLa présente garantie limitée ne couvre pas Garantie DU Système DE Ventilation KitchenaidAll rights reserved W10268948C

W10268948C specifications

The KitchenAid W10268948C is an innovative replacement water filter designed specifically for certain KitchenAid refrigerators. This water filter provides consumers with clean and refreshing water right from their appliances, ensuring that families can enjoy healthier hydration and better-tasting beverages.

One of the main features of the W10268948C is its advanced filtration technology. The filter effectively reduces a wide range of contaminants found in tap water, including chlorine, lead, and sediment, ensuring that the water remains pure and safe for daily consumption. This is especially important for households that rely heavily on filtered water for cooking and drinking.

The installation process for the W10268948C is straightforward, allowing users to easily replace their old filter without requiring professional assistance. Its design features a simple twist-and-lock mechanism that ensures a secure fit, minimizing the risk of leaks. Users can expect enhanced performance with each new filter, which translates to optimal water quality and taste.

Another noteworthy characteristic is the longevity of the filter. The W10268948C typically has a lifespan of up to six months or approximately 200 gallons, depending on the water quality and usage within the household. This endurance allows for a more extended period between replacements, providing convenience and peace of mind to busy families.

Additionally, the filter is certified by various third-party organizations, assuring consumers of its performance and safety standards. This certification adds a layer of credibility to its claims, making it a trusted choice among users.

Moreover, the W10268948C is environmentally friendly, as it minimizes plastic waste by ensuring that users have access to clean water at home, reducing the need for bottled water. This contributes positively to environmental conservation.

In conclusion, the KitchenAid W10268948C stands out as an efficient water filter that emphasizes safety, convenience, and sustainability. With its advanced filtration technology, easy installation process, long lifespan, and reliable performance, it remains a top choice for homeowners seeking to enhance the quality of their drinking water. Investing in this filter is a step toward healthier living and sustainable practices in the kitchen.