KitchenAid W10268948C Installation Requirements, ToolsandParts, Location Requirements

Page 5

INSTALLATION REQUIREMENTS

ToolsandParts

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

Tools needed

Level

Drill

1¼" (3 cm) drill bit

³⁄₃₂" (2.4 mm) drill bit

¹⁄₈" (3 mm) drill bit

Pencil

Wire stripper or utility knife

Tape measure or ruler

Pliers

Caulking gun and weatherproof caulking compound

Vent clamps

Jigsaw or keyhole saw

Flat-blade screwdriver

Metal snips

Phillips screwdriver

Scissors

Parts needed

Home power supply cable

1 - ½" (12.7 mm) UL listed or CSA approved strain relief

2 UL listed wire connectors

For vented installations, you will also need:

1 wall or roof cap

Metal vent system

For non-vented (recirculating) installations, you will also need:

Recirculation Kit Part Number W10271501 for non-vented (recirculating) installations only. See “Assistance or Service” section to order.

Parts supplied

Remove parts from packages. Check that all parts are included.

2 metal grease filters for 30" (76.2 cm) models

3 metal grease filters for 36" (91.4 cm) models

6 - flat head screws

2 - chimney mounting brackets

6 - #10 Phillips head mounting screws

Upper chimney cover

Lower chimney cover

Damper

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

Have a qualified technician install the range hood. It is the installer's responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located inside the range hood on the rear wall of the range hood.

Canopy range hood location should be away from strong draft areas, such as windows, doors and strong heating vents.

Cabinet opening dimensions that are shown must be used. Given dimensions provide minimum clearance.

Grounded electrical outlet is required. See “Electrical Requirements” section.

The canopy range hood is factory set for venting through the roof or through the wall. For non-vented (recirculating) Installation see “Non-vented (recirculating) Installations” in “Prepare Location” section. Recirculation Kit Part Number W10271501 is available from your dealer or an authorized parts distributor.

All openings in ceiling and wall where canopy range hood will be installed must be sealed.

For Mobile Home Installations

The installation of this range hood must conform to the Manufactured Home Construction Safety Standards, Title 24 CFR, Part 328 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD, Part 280) or when such standard is not applicable, the standard for Manufactured Home Installation 1982 (Manufactured Home Sites, Communities and Setups) ANSI A225.1/NFPA 501A*, or latest edition, or with local codes.

Product Dimensions

Vented Installations

 

11¹³⁄₁₆"

 

 

 

(30.0 cm)

 

 

10¼"

 

 

 

 

(26. 0 cm)

 

 

 

 

Upper

 

 

 

 

 

 

25⁵⁄₈"(65.1 cm)

chimney

 

 

min.

 

 

 

 

 

37¼" (94.6 cm)

 

 

 

max.

 

21¼"

overall chimney

 

height

Lower

(54.0 cm)

 

 

chimney

4¾"

(12.1 cm)

19¼"

(48.9 cm)

30" (76.2 cm) model: 29¹⁵⁄₁₆"(76.0 cm)

36" (91.4 cm) model: 35³⁄₈"(89.9 cm)

5

Image 5
Contents Canopy Hood Table DES Matières Table of ContentsYour safety and the safety of others are very important Range Hood SafetyImportant Safety Instructions Location Requirements Installation RequirementsToolsandParts Cold weather installations Installation DimensionsVentingRequirements Makeup airElectrical Requirements For non-vented recirculating installationsRear discharge Calculating Vent System LengthRange Hood Mounting Screws Installation Installation InstructionsChimney Support Bracket Installation PrepareLocationVented Installations InstallRange HoodNon-vented recirculating Installations Make Electrical ConnectionFor Vented Installations Install Chimney CoversInstall Upper Chimney Cover Install Lower Chimney CoverRange Hood USE Complete InstallationRange Hood Care CleaningWiring Diagram Accessories Assistance or ServiceIntheU.S.A InCanadaThis limited warranty does not cover Kitchenaid Ventilation WarrantyPage Votre sécurité et celle des autres est très importante Sécurité DE LA Hotte DE CuisinièreImportantes Instructions DE Sécurité Outillageetpièces Exigences DinstallationExigences demplacement Dimensions à respecter lors de linstallation Dimensions du produitInstallations avec décharge à lextérieur Installations sans décharge à lextérieur recyclageExigences concernant lévacuation Calcul de la longueur effective du circuit dévacuation SpécificationsélectriquesExemple de système de décharge Composant Conduit de diamètre 15,2 cm Coude àPréparationdelemplacement Instructions DinstallationInstallation des vis de montage de la hotte Installation de la bride de support de la cheminéeInstallations avec décharge à lextérieur Installationdela hotteInstallations sans décharge à lextérieur recyclage Achever la préparationRaccordementélectrique Acheverl’installation Installationducache-cheminéeInstallation de la section supérieure du cache-cheminée Installation de la section inférieure du cache-cheminéeNettoyage Utilisation DE LA HotteEntretien DE LA Hotte Installation des filtres à charbon Réinstallation des filtres à graisse métalliquesRemplacement des filtres à charbon Remplacement dune lampe à halogèneSchéma DE Câblage Accessoires Assistance OU ServiceLa présente garantie limitée ne couvre pas Garantie DU Système DE Ventilation KitchenaidAll rights reserved W10268948C

W10268948C specifications

The KitchenAid W10268948C is an innovative replacement water filter designed specifically for certain KitchenAid refrigerators. This water filter provides consumers with clean and refreshing water right from their appliances, ensuring that families can enjoy healthier hydration and better-tasting beverages.

One of the main features of the W10268948C is its advanced filtration technology. The filter effectively reduces a wide range of contaminants found in tap water, including chlorine, lead, and sediment, ensuring that the water remains pure and safe for daily consumption. This is especially important for households that rely heavily on filtered water for cooking and drinking.

The installation process for the W10268948C is straightforward, allowing users to easily replace their old filter without requiring professional assistance. Its design features a simple twist-and-lock mechanism that ensures a secure fit, minimizing the risk of leaks. Users can expect enhanced performance with each new filter, which translates to optimal water quality and taste.

Another noteworthy characteristic is the longevity of the filter. The W10268948C typically has a lifespan of up to six months or approximately 200 gallons, depending on the water quality and usage within the household. This endurance allows for a more extended period between replacements, providing convenience and peace of mind to busy families.

Additionally, the filter is certified by various third-party organizations, assuring consumers of its performance and safety standards. This certification adds a layer of credibility to its claims, making it a trusted choice among users.

Moreover, the W10268948C is environmentally friendly, as it minimizes plastic waste by ensuring that users have access to clean water at home, reducing the need for bottled water. This contributes positively to environmental conservation.

In conclusion, the KitchenAid W10268948C stands out as an efficient water filter that emphasizes safety, convenience, and sustainability. With its advanced filtration technology, easy installation process, long lifespan, and reliable performance, it remains a top choice for homeowners seeking to enhance the quality of their drinking water. Investing in this filter is a step toward healthier living and sustainable practices in the kitchen.