KitchenAid 4360369, 4329223 Electrical requirements, Installation steps, Preparation

Page 5

Electrical requirements

Important: Observe all governing codes and ordinances.

It is the customer’s responsibility:

•To contact a qualified electrical installer.

•To assure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70

— latest edition*, or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No.0-M91 - latest edition** and all local codes and ordinances.

If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate.

A 120-volt, 60 Hz, AC-only, fused electrical supply is required on a

separate 15-amp circuit, fused on both sides of the line.

Do not ground to a gas pipe.

Check with a qualified electrician if you are not sure range hood is properly grounded.

Do not have a fuse in the neutral or ground circuit.

IMPORTANT:

Save Installation Instructions for electrical inspector’s use.

The range hood must be connected with copper wire only.

The range hood should be connected directly to the fused disconnect (or circuit breaker) box through flexible armored or nonmetallic sheathed copper cable. A U.L.- or C.S.A.- listed strain relief must be provided at each end of the power

supply cable. Wire sizes (COPPER WIRE ONLY) and connections must conform with the rating of the appliance as specified on the model/serial rating plate.

Wire sizes must conform to the requirements of the National Electrical Code ANSI/NFPA 70 — latest edition*, or CSA Standards C22.1-94, Canadian Electrical Code Part 1 and C22.2 No.

0-M91 - latest edition** and all local codes and ordinances.

A U.L.- or C.S.A.- listed conduit connector must be provided at each end of the power supply cable (at the range hood and at the junction box).

Copies of the standards listed may be obtained from:

*National Fire Protection Association Batterymarch Park

Quincy, Massachusetts 02269

**CSA International

8501 East Pleasant Valley Road Cleveland, Ohio 44131-5575

Installation steps

Preparation

Because of the size and weight of this island canopy hood, the support sys- tem must be securely attached to the ceiling.

—For plaster or sheet rock ceilings, the support must be attached to joists.

—If this is not possible, you must build a support structure behind the plaster or sheet rock.

Do Not cut a joist or stud unless absolutely necessary. If a joist or stud must be cut, then a supporting frame must be constructed.

Before making cutouts, make sure there is proper clearance within the ceiling or wall for exhaust vent.

1. Put a thick, protective covering over countertop, cooktop or range to protect from damage or dirt. Select a flat surface for assembling the unit.

Cover that surface with a protective covering and place all hood parts and hardware on it.

2. Determine and mark the centerline on the ceiling where the range hood will be installed.

3. Using the mounting template, mark the location of the support mounting bracket holes, vent cutout (if used) and power supply cable cutout on the ceiling. Use 1-1/4"

(3.2 cm) drill and saber saw or keyhole saw to cut openings for power supply cable and vent. (See “Venting requirements” and “Electrical requirements,” Pages 3-5.

4. If venting to the outside install vent system. (See “Venting requirements”, Page 3.) Use caulking to seal exterior wall or roof openings.

5. Run wiring through ceiling according to the National Electrical Code or CSA Standards and local codes and ordinances. There must be enough power supply cable from the fused disconnect (or circuit breaker) box the to make the connections in the hood‘s terminal box.

Do Not turn on power until installation is completed.

Use caulking to seal all openings.

Installation

screw

screws

upper chimney

screw

6. Remove the four screws on the upper chimney and disassemble chimney pieces from support frame.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Quick Reference Installation Instructions Use and Care GuideParts needed Your safety and the safety Others is very importantParts supplied Tools neededFor the most efficient and quiet operation Product dimensionsVenting requirements Calculating the vent system length Venting methodsInstallation Installation stepsElectrical requirements Preparation Disconnect power supply Excessive Weight HazardElectrical connection Concrete ceiling use inserts and screws providedCheck operation Install chimney sectionsOperation CleaningUse and Care Information Maintenance Wiring diagram AccessoriesUtensil Bar Charcoal FiltersKitchenAid will not PAY for WarrantyKitchenAid will PAY for Our consultants provide assistance with Requesting Assistance or Service807 area code in Ontario Direct service branchesExcept 807 area code Pages Référence rapidePièces fournies Pièces nécessairesOutillage nécessaire Votre sécurité et celle des autres Est très importanteCircuit de décharge de l’air Dimensions du produit Dimensions des placardsDécharge horizontale à travers le mur Calcul de la longueur effective du système de déchargeInstallation Les étapes de l’installationAlimentation électrique Préparation12.Exécution des raccordements électriques Plafond de bois utiliser des vis à bois de 10,2 cm 4 po Interrompre l’alimentation électrique Vis Mm 1/4 poHotte Mettre le système sous tensionContrôler le fonctionnement de la Renseignements d’utilisation et entretien Fermeture du logement des organes de commandeUtilisation de la hotte NettoyageEntretien AccessoiresSchéma de câblage Filtres au charbonGarantie de la hotte d’aspiration KitchenAid GarantieKitchenAid Paiera KitchenAid NE Paiera PASSi vous avez besoin dassistance ou de service aux É.-U Demande dassistance ou de serviceSi vous avez besoin de pièces de rechange Pour plus dassistanceSi vous avez besoin dassistance ou de service au Canada Demande d’assistance ou de servicePour plus d’assistance 30 et 18 h 00 HNE, en composant

4360369, 4329223 specifications

The KitchenAid 4329223 and 4360369 stand as two prominent models in the KitchenAid lineup, recognized for their exceptional performance and reliability in home cooking and baking. These stand mixers showcase the brand’s commitment to quality, durability, and innovative technology, making them essential kitchen companions for both amateur cooks and seasoned chefs.

The KitchenAid 4329223 model features a robust 325-watt motor, enabling it to handle a wide range of tasks, from kneading tough bread dough to whipping delicate meringue. The mixer is equipped with a 10-speed control, offering precision and versatility. Users can easily adjust the speed for different recipes, ensuring optimal mixing for every ingredient. This flexibility allows for improved results whether you are blending thick batters, aerating egg whites, or mixing cookie dough.

On the other hand, the KitchenAid 4360369 is designed with a powerful 400-watt motor, providing extra strength for heavier mixtures. This model comes with a bowl-lift design, facilitating easy access to the mixing bowl and making it ideal for large batches. The sturdy construction of the 4360369 enhances stability during operation, allowing users to mix without the worry of the machine moving around the countertop.

Both models are equipped with the iconic planetary mixing action, which ensures that all ingredients are mixed thoroughly. The mixing attachment rotates in one direction while the bowl spins in the opposite direction, covering every corner of the bowl and ensuring consistent blending. Additionally, these mixers come with a variety of included attachments, such as the flat beater, dough hook, and wire whip, enabling users to tackle an array of culinary tasks.

The design aesthetics of both models also warrant mention. With a classic yet modern look, they feature a sturdy stainless-steel bowl that is both durable and easy to clean. Available in a variety of colors, these mixers not only perform exceptionally but also enhance the décor of any kitchen.

Overall, the KitchenAid 4329223 and 4360369 represent the best of technology, design, and functionality, catering to the needs of anyone looking to elevate their culinary skills. With their reliable performance and versatile features, these mixers make cooking and baking an enjoyable and efficient experience.
Top Page Image Contents