KitchenAid LI32NA/W10674120B Installation Requirements, Tools and Parts, Location Requirements

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

Tools needed

■Drill

■1¹⁄₄" (3.2 cm) drill bit

■¹⁄₈" (3.2 mm) drill bit for pilot holes

■Pencil

■Wire stripper or utility knife

■Tape measure or ruler

■Caulking gun and weatherproof caulking compound

■Flat-blade screwdriver

■Phillips screwdriver

■Saber or keyhole saw

■Vent clamps

■Metal snips

■Compass or circle template

Parts supplied

Remove parts from package. Check that all parts are included.

■2 - Metal filters

■4 - 4.5 x 13 mm mounting screws

■2 - 3.5 x 9.5 mm damper screws

■6" (15.2 cm) transition with damper

■4 - 5 x 45 mm screws

■10 x 50 mm wall anchors

■T10® Torx®† adapter

■T20® Torx® adapter

Parts needed

■Home power supply cable

■½" (12.7 mm) UL listed or CSA approved strain relief

■3 - UL listed wire connectors

For top vented installations:

■6" (15.2 cm) round metal venting

■1 - wall or roof cap

For non-vented (recirculating) installations:

■Recirculating Kit W10490330 - See Assistance or Service section to order.

■6" (15.2 cm) round metal venting

For rear vented installations:

■3¹⁄₄" x 10" (8.3 x 25.4 cm) round metal venting

■1 - wall or roof cap

■3¹⁄₄" x 10" (8.3 x 25.4 cm) damper/vent connector (see the “Assistance or Service” section to order)

For cabinets with recessed bottoms:

■2 - 2" (5.1 cm) wide filler strips. Length and thickness determined by recess dimensions.

■4 - flat-head wood screws or machine screws with washers and nuts (to attach filler strips).

†®TORX, T10 and T20 are registered trademarks of Acument Intellectual Properties, LLC.

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

■It is the installer’s responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located inside the range hood on the left wall.

■Range hood location should be away from strong draft areas, such as windows, doors and strong heating vents.

■Cabinet opening dimensions that are shown must be used. Given dimensions provide minimum clearance. Consult the cooktop/range manufacturer installation instructions before making any cutouts.

■This range hood is recommended for use with cooktop with a maximum total rating of 65,000 BTUs or less.

■Grounded electrical outlet is required. See “Electrical Requirements” section.

■The range hood is factory-set for vented installations. For non-vented (recirculating) installations, the Recirculation Kit is W10490330. Replacement Charcoal Filters Part Number is

W10272068. See the “Assistance or Service” section to order.

■All openings in ceiling and wall where range hood will be installed must be sealed.

For Mobile Home Installations

The installation of this range hood must conform to the Manufactured Home Construction Safety Standards, Title 24 CFR, Part 328 (formerly the Federal Standard for Mobile Home Construction and Safety, title 24, HUD, Part 280) or when such standard is not applicable, the standard for Manufactured Home Installation 1982 (Manufactured Home Sites, Communities and Setups) ANSI A225.1/NFPA 501A, or latest edition, or with local codes.

Product Dimensions

12"		1³⁄₁₆"
		(3.0 cm)
(30.5 cm)
	7¼"
	(18.4 cm)	3" (7.6 cm) -
	1¹⁄₁₆"	30" (76.2 cm) model
2"		5³⁄₄" (14.6 cm) -
	(2.6 cm)
(5.1 cm)		36" (91.4 cm) model
9"
(22.9 cm)
	13¹²⁄₁₆"	⁵⁄₈"
	(35 cm)	(1.6 cm)

29⁷⁄₈" (75.9 cm) - 30" (76.2 cm) model	19³⁄₄"
35⁷⁄₈ (91.1 cm) - 36" (91.4 cm) model
	(50.2 cm)

4