Installation Instructions

Electrical Requirements

Observe all governing codes and ordinances.

Ensure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70 (latest edition), or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes and ordinances.

If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02169-7471

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

■A 120 volt, 60 Hz., AC only, 15-amp, fused electrical circuit is required.

■If the house has aluminum wiring, follow the procedure below:

1.Connect a section of solid copper wire to the pigtail leads.

2.Connect the aluminum wiring to the added section of copper wire using special connectors and/or tools designed and UL listed for joining copper to aluminum.

Follow the electrical connector manufacturer's recommended procedure. Aluminum/copper connection must conform with local codes and industry accepted wiring practices.

■Wire sizes and connections must conform with the rating of the appliance as specified on the model/serial rating plate. The model/serial plate is located behind the filter on the rear wall of the range hood.

■Wire sizes must conform to the requirements of the National Electrical Code, ANSI/NFPA 70 (latest edition), or CSA Standards C22. 1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes and ordinances.

Prepare Location

NOTE: For vented installations, it is recommended that the vent system be installed before the hood is installed.

Before making cutouts, make sure there is proper clearance within the ceiling or wall for exhaust vent.

NOTE: The exhaust adapter/damper can be installed up to 1" (2.5 cm) on either side of the hood center to accommodate off- center ductwork.

1.Disconnect power.

2.Determine which venting method to use: roof or wall.

NOTE: For rear venting a Damper Assembly Kit must be used. See “Assistance or Service” section to order.

3.Select a flat surface for assembling the range hood. Place covering over that surface.

WARNING

Excessive Weight Hazard

Use two or more people to move and install range hood.

Failure to do so can result in back or other injury.

4.Using 2 or more people, lift the range hood and set it upside down onto covered surface.

5.If cabinet has recessed bottom, add wood filler strips on each side. Install screws to attach filler strips in locations shown.

Wood filler strips (recessed cabinet bottoms only)

3" (7.6 cm)

Cabinet

bottom

3" (7.6 cm)

Wall

Determine Wiring Hole Location

Cut only one 1¹⁄₄" (3.2 cm) diameter wiring access hole. See Step 2 for wiring hole location instructions.

1.Determine and clearly mark a vertical centerline on the wall and cabinet in the area the vent opening will be made.

A. Centerline

2.To wire through top:

Mark a line distance “A” from the left of the centerline on the underside of the cabinet. Mark the point on this line that is 2" (5.1 cm) from back wall. Drill a 1¼" (3.2 cm) diameter hole through the cabinet at this point.

A	2"	(5.1	cm)
	from wall,
	not cabinet
	frame

Centerline

A. 12" (30.5 cm) for 30" (76.2 cm) models 12¼" (31.1 cm) for 36" (91.4 cm) models

LI32NA/W10674120B specifications

The KitchenAid LI32NA/W10674120B is an innovative and versatile addition to any contemporary kitchen. Designed with precision and efficiency in mind, this model encapsulates the quality and craftsmanship that KitchenAid is renowned for. One of the standout features of this appliance is its impressive dual cooling system, which ensures optimal temperature control and humidity management, preserving the freshness of food for extended periods.

Equipped with an energy-efficient inverter compressor, the LI32NA minimizes the fluctuations in temperature that can compromise food quality. This technology operates quietly, making it ideal for open-plan living spaces where sounds can travel. Additionally, this model includes a robust LED lighting system that illuminates every corner of the refrigerator, providing clear visibility to all stored items while also being energy-efficient.

The interior layout of the LI32NA/W10674120B is both practical and stylish, featuring adjustable glass shelves that allow for maximum flexibility in organizing food and beverages. The spacious design incorporates specialized compartments, including a crisper drawer for fruits and vegetables, ensuring they remain crisp and flavorful.

Moreover, this model boasts an advanced filtration system that helps eliminate unwanted odors and contaminants, enhancing the overall quality of the air in the refrigerator. The exterior is complemented by a sleek stainless-steel finish that not only adds a touch of elegance but is also easy to clean and resistant to fingerprints.

For those who appreciate technology, the LI32NA/W10674120B comes with smart connectivity options, enabling users to monitor and adjust settings remotely through a compatible mobile application. This feature ensures that you can manage your appliance even when you’re away from home.

Overall, the KitchenAid LI32NA/W10674120B is a perfect fusion of style, functionality, and cutting-edge technology. Its attention to detail and commitment to preserving food quality makes it an excellent choice for anyone looking to upgrade their kitchen. Whether you're a culinary enthusiast or simply seeking convenience, this refrigerator is designed to meet a variety of lifestyle needs, making meal preparation and food storage simpler and more enjoyable.