KitchenAid 9763382 installation instructions Installation Instructions, Install Chimney Support

Page 7

INSTALLATION INSTRUCTIONS

Install Chimney Support

Because of the size and weight of this island hood, the chimney support must be securely attached to the ceiling.

■For plaster or drywall ceilings, the chimney support must be attached to joists. If this is not possible, you must build a support structure behind the plaster or drywall.

■Do not cut a joist or stud unless absolutely necessary. If a joist or stud must be cut, then a supporting frame must be constructed.

■Before making cutouts, make sure there is proper clearance within the ceiling or wall for exhaust vent.

WARNING

Excessive Weight Hazard

Use two or more people to move and install range hood. Failure to do so can result in back or other injury.

1.Select a flat surface for assembling the hood. Cover that surface with a protective covering such as a blanket or cardboard during assembly.

NOTE: Do not remove the plastic covering on the chimney covers at this time. The covering protects the chimney during installation.

2.Using two or more people, place all hood parts and hardware on the protective covering

The chimney section of the hood is shipped assembled. It must be disassembled for installation.

3.Slide apart the chimney covers.

4.Remove the lower chimney cover from the chimney support by removing the two Phillips screws on the outside bottom of the chimney cover.

5.Remove the upper chimney cover from the chimney support by removing the two Phillips screws on the outside top of the chimney cover.

6.Determine and mark the centerline on the ceiling where the hood will be installed, making sure that the hood is centered over the cooking surface.

7.Tape the template (supplied in the chimney support carton) to the ceiling and mark the mounting holes, electrical hole and vent location (if used) on the ceiling.

A

B

C

A. Template on ceiling

B.Centerline

C.Cooking surface

8.Drill pilot holes in the chimney support mounting hole locations for your attachment method.

9.Use a 1¹⁄₄" or 3.0 cm drill bit to drill the hole for the power supply cable.

10.If venting to the outside, cut the hole for the vent system in the ceiling and install the vent system. See “Venting Requirements” section.

11.If venting to the outside, place the round damper into the exhaust opening of the vent motor housing.

12.Remove the 4 chimney support ceiling attachment bolts from the parts bag and install in previously drilled pilot holes. Leave screw heads about ¹⁄₄" (6.4 mm) away from ceiling strips.

¹⁄₄" (6.4 mm)

13.If the extension kit is not being installed, go to “Complete Chimney Support Installation” section.

Installing Chimney Extension Kit (Optional)

1.Remove chimney extension cover (if factory assembled).

2.Position the chimney extension over the chimney support so that the outside edges and the electrical holes line up.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Pour Cuisine Configurée EN Îlot Range Hood Safety Table of ContentsTable DES Matières Important Safety Instructions Tools and Parts Installation RequirementsProduct Dimensions Recirculating chimney kit dimensionsVenting Requirements Installation ClearancesVenting Methods Calculating Vent System Length Electrical RequirementsInstall Chimney Support Installation InstructionsInstalling Chimney Extension Kit Optional Make Electrical Connection Complete Chimney Support InstallationChimney Extension Kit Installation Optional Install Chimney CoversVented Installation Option Recirculating Installation Option, Kit RequiredComplete Installation Install Range HoodOperation Range Hood USECheck Operation Accessories Cleaning and MaintenanceRange Hood Care For further assistance Requesting Assistance or ServiceIf you need replacement parts For parts, accessories and service in CanadaCall Kitchenaid Ventilation WarrantyWiring Diagram Votre sécurité et celle des autres est très importante Sécurité DE LA Hotte DE CuisinièreConservez CES Instructions Outillage et pièces Exigences DinstallationExigences demplacement Dimensions du produitDégagements de séparation à respecter Exigences concernant lévacuationMéthodes dévacuation Calcul de la longueur effective du circuit dévacuation Spécifications électriquesInstallation du support de cheminée Instructions DinstallationInstallation de lextension de cheminée option Raccordement électrique Achever linstallation du support de cheminéeInstallation avec décharge à lextérieur Option de linstallation du cache-cheminéeOption de linstallation avec recyclage, kit nécessaire Installation du kit dextension de cheminée option Installation de la hotte de cuisinièreContrôle du fonctionnement Achever linstallationFonctionnement CuisinièreNettoyage et entretien Remplacement dune lampe à halogène AccessoiresPour plus dassistance Demande Dassistance OU DE ServicePour pièces, accessoires et service au Canada Si vous avez besoin de pièces de rechangeGarantie Limitée DE UN AN GarantiedusystèmedeventilationkitchenaidSchéma DE Câblage Page 9763382

9763382 specifications

The KitchenAid 9763382 is a highly versatile accessory designed primarily for those who seek to enhance their culinary experiences in the kitchen. Known for its robust construction and user-friendly design, this attachment expands the functionality of various KitchenAid stand mixers, allowing home chefs to explore a range of culinary possibilities.

One of the standout features of the 9763382 is its ability to create fresh pasta at home. The attachment includes adjustable thickness settings, enabling users to customize pasta sheets according to their desired thickness, whether it's for lasagna, fettuccine, or ravioli. This level of control enhances the cooking experience, giving users the opportunity to craft pasta that suits their taste perfectly.

In addition to pasta-making capabilities, the KitchenAid 9763382 is built from high-quality materials that ensure durability and long-lasting performance. The stainless steel construction is not only aesthetically pleasing but also resistant to rust and corrosion, making it easy to clean and maintain. Users can expect a product that withstands frequent use without compromising on quality.

Another key characteristic of the KitchenAid 9763382 is its compatibility with a range of KitchenAid mixer models, making it a versatile addition to existing kitchen equipment. Its easy attachment to the stand mixer simplifies the process of creating homemade dough and pasta, removing the need for additional appliances and saving valuable counter space.

The design of the KitchenAid 9763382 also prioritizes ease of use. Clear instructions guide users through the pasta-making process, making it accessible even for those who may be new to the art of pasta preparation. The attachment's straightforward assembly means that it can be set up and taken down with minimal effort, making the experience enjoyable rather than cumbersome.

In terms of technology, the 9763382 leverages KitchenAid's innovative engineering, ensuring a seamless integration with the stand mixer’s motor for efficient operation. The powerful performance reduces the time spent on food preparation, enabling users to focus on creativity in the kitchen.

Overall, the KitchenAid 9763382 is an essential tool for those passionate about cooking. With its combination of versatility, ease of use, and durable design, it transforms the way users approach pasta making and dough mixing, allowing them to bring authentic Italian cuisine into their homes with ease.
Top Page Image Contents