KitchenAid 36" (91.4 cm) 48" (121.9 cm) Island Canopy Range Hood Electrical requirements

Page 5

Electrical requirements

Important: Observe all governing codes and ordinances.

It is the customer’s responsibility:

•To contact a qualified electrical installer.

•To assure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70

— latest edition*, or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No.0-M91 - latest edition** and all local codes and ordinances.

If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate.

A 120-volt, 60 Hz, AC-only, fused electrical supply is required on a

separate 15-amp circuit, fused on both sides of the line.

Do not ground to a gas pipe.

Check with a qualified electrician if you are not sure range hood is properly grounded.

Do not have a fuse in the neutral or ground circuit.

IMPORTANT:

Save Installation Instructions for electrical inspector’s use.

The range hood must be connected with copper wire only.

The range hood should be connected directly to the fused disconnect (or circuit breaker) box through flexible armored or nonmetallic sheathed copper cable. A U.L.- or C.S.A.- listed strain relief must be provided at each end of the power

supply cable. Wire sizes (COPPER WIRE ONLY) and connections must conform with the rating of the appliance as specified on the model/serial rating plate.

Wire sizes must conform to the requirements of the National Electrical Code ANSI/NFPA 70 — latest edition*, or CSA Standards C22.1-94, Canadian Electrical Code Part 1 and C22.2 No.

0-M91 - latest edition** and all local codes and ordinances.

A U.L.- or C.S.A.- listed conduit connector must be provided at each end of the power supply cable (at the range hood and at the junction box).

Copies of the standards listed may be obtained from:

*National Fire Protection Association Batterymarch Park

Quincy, Massachusetts 02269

**CSA International

8501 East Pleasant Valley Road Cleveland, Ohio 44131-5575

Installation steps

Preparation

Because of the size and weight of this island canopy hood, the support sys- tem must be securely attached to the ceiling.

—For plaster or sheet rock ceilings, the support must be attached to joists.

—If this is not possible, you must build a support structure behind the plaster or sheet rock.

Do Not cut a joist or stud unless absolutely necessary. If a joist or stud must be cut, then a supporting frame must be constructed.

Before making cutouts, make sure there is proper clearance within the ceiling or wall for exhaust vent.

1. Put a thick, protective covering over countertop, cooktop or range to protect from damage or dirt. Select a flat surface for assembling the unit.

Cover that surface with a protective covering and place all hood parts and hardware on it.

2. Determine and mark the centerline on the ceiling where the range hood will be installed.

3. Using the mounting template, mark the location of the support mounting bracket holes, vent cutout (if used) and power supply cable cutout on the ceiling. Use 1-1/4"

(3.2 cm) drill and saber saw or keyhole saw to cut openings for power supply cable and vent. (See “Venting requirements” and “Electrical requirements,” Pages 3-5.

4. If venting to the outside install vent system. (See “Venting requirements”, Page 3.) Use caulking to seal exterior wall or roof openings.

5. Run wiring through ceiling according to the National Electrical Code or CSA Standards and local codes and ordinances. There must be enough power supply cable from the fused disconnect (or circuit breaker) box the to make the connections in the hood‘s terminal box.

Do Not turn on power until installation is completed.

Use caulking to seal all openings.

Installation

screw

screws

upper chimney

screw

6. Remove the four screws on the upper chimney and disassemble chimney pieces from support frame.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Installation Instructions Use and Care Guide Parts needed Your safety and the safety Others is very importantParts supplied Tools neededFor the most efficient and quiet operation Product dimensionsVenting requirements Calculating the vent system length Venting methodsInstallation Installation stepsElectrical requirements Preparation Disconnect power supply Excessive Weight HazardConcrete ceiling use inserts and screws provided Failure to do so can result in back or other injuryCheck operation Install chimney sectionsOperation CleaningUse and Care Information Maintenance Wiring diagram AccessoriesUtensil Bar Charcoal FiltersKitchenaid Ventilation Warranty WarrantyOur consultants provide assistance with Requesting Assistance or Service807 area code in Ontario Direct service branchesExcept 807 area code 4329223/9763387 Référence rapidePages Pièces fournies Pièces nécessairesOutillage nécessaire Votre sécurité et celle des autres Est très importanteCircuit de décharge de l’air Dimensions du produit Dimensions des placardsDécharge horizontale à travers le mur Calcul de la longueur effective du système de déchargeInstallation Les étapes de l’installationAlimentation électrique Préparation12. Exécution des raccordements électriques Plafond de bois utiliser des vis à bois de 10,2 cm 4 po Interrompre l’alimentation électrique Vis Mm 1/4 poHotte Mettre le système sous tensionContrôler le fonctionnement de la Renseignements d’utilisation et entretien Fermeture du logement des organes de commandeUtilisation de la hotte NettoyageEntretien AccessoiresSchéma de câblage Filtres au charbonGarantiedusystèmedeventilationkitchenaid GarantieSi vous avez besoin dassistance ou de service aux É.-U Demande dassistance ou de serviceSi vous avez besoin de pièces de rechange Pour plus dassistanceSi vous avez besoin dassistance ou de service au Canada Demande d’assistance ou de servicePour plus d’assistance 30 et 18 h 00 HNE, en composant

36" (91.4 cm) 48" (121.9 cm) Island Canopy Range Hood specifications

The KitchenAid 36" (91.4 cm) and 48" (121.9 cm) Island Canopy Range Hoods are designed to enhance both the functionality and aesthetic appeal of your kitchen. These powerful ventilation systems are perfect for chefs who demand excellence in their cooking environment, merging innovative technology with a sleek, modern look.

One of the key features of these range hoods is their high-performance ventilation capabilities. With multiple fan speeds, the Island Canopy Range Hoods can effectively remove smoke, steam, and cooking odors. The powerful motors ensure that your kitchen remains a pleasant and inviting space, regardless of the intensity of your cooking.

The hoods are equipped with high-quality stainless steel construction, providing durability and a contemporary aesthetic that complements various kitchen designs. The smooth surface is easy to clean and resists fingerprints and smudges, making maintenance a breeze.

The baffle filters are another notable characteristic of these hoods. Designed to effectively capture grease and other particles, these filters are not only efficient but are also dishwasher-safe, simplifying clean-up processes. Additionally, the range hoods feature a convenient filter reminder to alert you when it's time for cleaning or replacement.

In terms of lighting, the KitchenAid Island Canopy Range Hoods incorporate integrated LED task lighting. This feature illuminates your cooking surface, enhancing visibility while adding a stylish glow to your kitchen. The lights can be adjusted to accommodate different cooking tasks, ensuring you have the right amount of illumination at all times.

Another significant aspect is the quiet operation of these hoods. With sound-dampening technology, they provide powerful ventilation while minimizing noise, allowing for a more enjoyable kitchen experience. This is particularly beneficial when entertaining guests or during family gatherings when conversation is key.

The installation options for the KitchenAid Island Canopy Range Hoods are flexible, making them suitable for various kitchen layouts. They can be easily mounted above an island cooktop, providing both functionality and a striking focal point in your kitchen.

In summary, the KitchenAid 36" and 48" Island Canopy Range Hoods offer a combination of powerful performance, modern design, and user-friendly features. With their advanced technologies and thoughtful construction, they are an excellent addition to any culinary space, helping to create an optimal cooking environment while enhancing the overall kitchen experience.
Top Page Image Contents