KitchenAid W10206423A manual Vacation and Moving Care, To shut down the ice maker

Page 12

9.Remove, clean and replace the ice scoop and ice scoop holder.

■After removing the ice scoop, remove the holder by removing the two thumb screws.

■Wash the ice scoop holder along with the other interior components using the following instructions.

■Replace the ice scoop holder by replacing the thumb screws.

A

B

A. Thumb screw

B. Ice scoop holder

10.Wash the interior components (cutter grid, exterior of hoses, and water pan) and the storage bin, door gasket, ice scoop, and ice scoop holder with mild soap or detergent and warm water. Rinse in clean water. Then clean the same parts with a solution of 1 tbs (15 mL) of household bleach in 1 gal. (3.8 L) warm water. Rinse again thoroughly in clean water.

NOTE: Do not remove hoses. Do not wash plastic parts in dishwasher. They cannot withstand temperatures above 145°F (63°C).

11.Replace water pan by pushing back on the bottom with one hand while pushing up and back on the top. Secure the water pan by replacing both screws.

12.Check the following:

■Drain cap from the water pan is securely in place. If the drain cap is loose, water will empty from the water pan, and you will have either thin ice or no ice.

■Hose from water pan is inserted into storage bin drain opening.

13.Slide the cutter grid back into place and secure it by replacing the right-hand screw and plastic spacer. Then tighten the left-hand screw. Reconnect the cutter grid harness and the ice level sensor harness.

14.Replace the cutter grid cover and the two screws.

15.Gently wipe the control panel with a soft, clean dishcloth using warm water and a mild liquid dish detergent.

16.Plug in ice maker or reconnect power.

17.After cleaning, make sure that all controls are set properly and that no control indicators are flashing.

Vacation and Moving Care

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

To shut down the ice maker:

1.Unplug ice maker or disconnect power.

2.Remove all ice from storage bin.

3.Shut off the water supply.

4.Remove the two screws in the lower access panel and the two screws from the base grille area of the front panel support. Pull forward to remove the lower access panel.

5.Disconnect the inlet and outlet lines to water valve. Allow these lines to drain and then reconnect to the valve.

6.Replace lower access panel and screws.

7.Drain water from water pan by removing the drain cap.

8.If the room temperature will drop below 32°F (0°C), water must be removed from the drain line.

For ice makers with a drain pump installed:

■Plug in ice maker or reconnect power.

■Turn ice maker off and remove all remaining ice from ice bin.

■Pour 1 qt (0.95 L) of water into the ice bin near the drain and let the ice maker stand for approximately 5 minutes. This will allow the water in the bin to drain into the drain pump so that the pump will remove the remaining water from the ice bin and the drain pump.

■Unplug ice maker or disconnect power.

9.Before using again, clean the ice maker and storage bin.

10.Plug into a grounded 3 prong outlet.

NOTE: All components of the ice maker are permanently lubricated at the factory. They should not require any additional oiling throughout the normal life of the machine.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents ICE Maker Table of Contents Table DES MatièresICE Maker Safety Your safety and the safety of others are very importantInstallation Instructions Cleaning Before UseUnpack the Ice Maker Location RequirementsElectrical Requirements Water Supply RequirementsLeveling Recommended grounding methodConnecting the Water Line Connect Water SupplyRear View Connecting the Drain Drain ConnectionIce Maker Door Gravity Drain SystemRemove Door Reverse HingesReplace Door Top HingeICE Maker USE Normal SoundsHow Your Ice Maker Works Ice Making ProcessCleaning Using the ControlsICE Maker Care Condenser Interior ComponentsDirty or clogged condenser For ice makers with a drain pump installed Vacation and Moving CareTo shut down the ice maker Troubleshooting Ice Maker OperationIce Production Assistance or Service Plumbing ProblemsIce Quality U.S.AKitchenaid ICE Maker Warranty Limited WarrantyItems Excluded from Warranty This limited warranty does not coverSécurité DE LA Machine À Glaçons Votre sécurité et celle des autres est très importanteInstructions D’INSTALLATION Exigences demplacementDéballage de la machine à glaçons Enlèvement des matériaux d’emballageMéthode de mise à la terre recommandée Spécifications électriquesSpécifications de l’alimentation en eau Alimentation en eau par osmose inverseNivellement Raccordement à la canalisation d’eauRaccordement du tuyau d’eau Outillage nécessaireRaccordement au drain de vidange Vidange par gravitéVUE Arrière Porte de la machine à glaçons Système avec pompe de vidange sur certains modèlesRaccordement du drain de vidange Dépose de la porteRéinstallation de la porte Inversion des charnièresCharnière supérieure Charnière inférieureUtilisation DE LA Machine À Glaçons Sons normauxFonctionnement de la machine à glaçons Fabrication de la glaceUtilisation des commandes Entretien DE LA Machine À GlaçonsNettoyage Condenseur Un condenseur sale ou obstruéComposants intérieurs Précautions à prendre avant les vacances Ou un déménagement Arrêt de la machine à glaçonsMachine à glaçons avec pompe de vidange Dépannage Production de glaçonsLa machine à glaçons ne fonctionne pas La machine à glaçons semble bruyanteQualité des glaçons Problèmes de plomberieLa grille ne découpe pas les plaques de glace Goût, odeur ou couleur grise des glaçonsAssistance OU Service Si vous avez besoin de pièces de rechangePour plus d’assistance Nos consultants fournissent l’assistance pourGarantie DE LA Machine À Glaçons Kitchenaid Garantie LimitéeÉléments Exclus DE LA Garantie La présente garantie limitée ne couvre pasW10206423A All rights reserved

W10206423A specifications

The KitchenAid W10206423A is a highly versatile and efficient appliance that enhances the culinary experience in any modern kitchen. Designed with attention to detail, this kitchen tool boasts several features and technologies that make it a must-have for both amateur cooks and professional chefs alike.

One of the standout features of the KitchenAid W10206423A is its powerful motor, which provides superior mixing capabilities. With an impressive wattage, the motor ensures consistent results whether you are whipping, kneading, or blending ingredients. This heavy-duty performance means you can tackle even the most demanding recipes with ease, making it an indispensable ally for baking, cooking, or food preparation tasks.

Equipped with a range of speed settings, the Kitchenaid W10206423A allows for personalized control over mixing techniques. From slow stirring for gentle ingredients to high-speed whipping for airy mixtures, the adjustable speeds provide the flexibility needed for a variety of recipes. This feature also minimizes splatter and promotes thorough ingredient incorporation, ensuring that your dishes yield professional-quality results.

Another characteristic that sets the KitchenAid W10206423A apart is its robust construction. Crafted from durable materials, this kitchen appliance is built to withstand the rigors of daily use. The design not only contributes to its longevity but also makes it easy to clean after use, enhancing your overall kitchen experience. The sleek design fits seamlessly in any kitchen décor, combining practicality with style.

Additionally, the KitchenAid W10206423A comes with a selection of attachments that broaden its functionality. From dough hooks to whisk attachments, these tools enable users to expand their culinary repertoire. Whether you're making bread, whipping cream, or mixing cake batter, the versatility of attachment options allows the appliance to adapt to various cooking needs.

In terms of safety, the KitchenAid W10206423A incorporates built-in features that ensure safe operation. The appliance is designed with a secure locking mechanism to prevent accidental start-ups, giving users peace of mind while they work.

In summary, the KitchenAid W10206423A is a powerful and adaptable kitchen appliance that caters to the needs of a diverse range of cooking tasks. With its robust motor, adjustable speed settings, durable construction, and versatility provided by various attachments, this model stands as an excellent investment for anyone looking to elevate their culinary skills. Whether you are a seasoned cook or just beginning your culinary journey, the KitchenAid W10206423A is sure to become an essential tool in your kitchen.
Top Page Image Contents