Philips HD8745, HD8743, HD8747 user manual Trouble Shooting, Problem Possible Cause Solution

Page 41

ENGLISH 39

TROUBLE SHOOTING

This chapter summarizes the most common problems you could encoun- ter with your machine. If you are unable to solve the problem with the information below, visit www.philips.com/support for a list of frequently asked questions or contact the Philips Saeco hotline in your country. You find its contact details in the warranty booklet bypacked separately or on www.philips.com/support.

Problem

Possible Cause

Solution

 

 

 

The machine does not turn

The machine is not connected to

Connect the machine to the power

on.

the power source.

source.

 

 

 

The coffee is not hot enough.

The cups are cold.

Preheat the cups with hot water.

 

 

 

Hot water or steam is not

The hole of the hot water/steam

Clean the hole of the hot water/

dispensed.

wand is clogged.

steam wand using a pin.

 

 

Make sure that the machine is

 

 

turned off and has cooled down

 

 

before performing this operation.

 

 

 

 

Pannarello is dirty (if supplied).

Clean the Pannarello.

The espresso does not have enough crema (see note).

The coffee blend is unsuitable, the coffee is not freshly roasted or the grind is too coarse.

Change coffee blend or adjust the ceramic coffee grinder as explained in section “How to adjust the ce- ramic coffee grinder”.

The machine takes a long time to warm up or the amount of water dispensed from the hot water/steam wand is too small

The machine’s water circuit is

Descale the machine.

clogged by limescale build-up.

 

The brew group cannot be removed.

The brew group is out of place.

Turn the machine on. Close the ser- vice door. The brew group automati- cally returns to the correct position.

 

The coffee grounds drawer is

Remove the coffee grounds drawer,

 

inserted.

thereafter remove the brew group.

 

 

 

The machine grinds the

The brew group is dirty.

Clean the brew group (section

coffee beans but no coffee

 

“Weekly Cleaning of the Brew

comes out (see note).

 

Group”).

 

 

 

 

The water circuit is not primed.

Fill the water tank with fresh water

 

 

and dispense hot water.

This may sometimes occur when the machine is automatically adjusting the dose.

Brew a few espressos as described in the section “Saeco Adapting System”.

 

The dispensing spout is dirty.

Clean the dispensing spout.

 

 

 

Image 41
Contents 02 EN Important Safeguards Instructions for the Power Supply Cord English English ContentsSafety Instructions Before cleaning the machine Always put the machine on a flat and stable surface Compliance with Standards 1016 18 19 InstallationGeneral description Preparing for use Preparing for USEMachine Packaging MAX Circuit priming Using the Machine for the First TimeAutomatic rinse/self-cleaning cycle Steady on Manual rinse cycleINTENZA+ water filter installation = Hard water standard C = Very hard water Saeco Adapting System AdjustmentsAdjusting the Ceramic Coffee Grinder Adjusting the Coffee Length Same procedure applies to the coffee button Espresso and Coffee Brewing Frothing milk Frothing Milk / Cappuccino BrewingEnglish Steam/Coffee Switchover Making a capuccino Dispensing HOT Water Daily Cleaning of the Machine Cleaning and MaintenanceDaily cleaning of water tank English Weekly Cleaning of the Brew Group and of the coffee exit duct English Monthly Lubrication of the Brew Group Preparation DescalingDescaling Rinsing Cycle English Control panel Light Signals Causes Meaning of the Warning SignalsLight Light Signals Causes SolutionsFlashing in counter-clockwise Direction Problem Possible Cause Solution Trouble ShootingProblem Possible Cause Disposal Energy SavingStand-by Guarantee and Service Technical SpecificationGuarantee ServiceOrdering Maintenance Products Page Page Rev.00 del