Basic Operation | Denon DN-S3000 instruction

PITCH BEND

ENGLISH

5BASIC OPERATION

Play and pause

•Each push of the i PLAY/PAUSE (13) button switches between playback and pause. PLAY/PAUSE (13) button illuminates solid green during playback and flashed in pause.

•When the i PLAY/PAUSE (13) button is pushed during play, the DN-S3000 pauses playback at that point. Push i PLAY/PAUSE (13) button once again and playback resumes.

•When the Scratch mode is set to MAIN, the Platter turns when the Main Track is played. When the rotation of Scratch Disc is stopped by pressing with the finger, the pause mode is set, and when the finger is released playback resumes.

NOTE:

Standing up of playback slows unusually after trans porting the product.At the time, push center of the !1 Scratch Disc lightly.

Push the @9SCRATCH

MODE button for more than

21 sec to set @9Scratch Disc to search mode. The

SCRATCH MODE button

LEDs will turn off.

Turn the !1Scratch Disc to change Cue point. You can hear the short sound of the current

3 Cue point.

When !1Scratch Disc is turned in the pause, standby or frame repeat mode, works as the manual search function.

After you found your preferred Cue point, push

4 the !0CUE button then new Cue point is set.

Pitch Bend

•With PITCH BEND function you can change pitch temporary. DN-S3000 has three ways for this function PITCH BEND buttons and Scratch Disc.

[PITCH BEND +/– buttons]

•Push the #3PITCH BEND

– or #4+ button for momentary change of

1pitch.

While holding these buttons down, the pitch continues to change up to the limitation.

•After releasing the PITCH BEND buttons, playback pitch returns to slider setting.

When the Scratch source is set to MAIN and the Platter is turning, playback of the Main source can be slowed temporarily by lightly pressing

2 !1Scratch Disc or PLATTER.

In addition, playback can be quickened

temporarily by pushing Scratch Disc or

Relay playback

•Relay Play function is a playback mode to continue play tracks of CDs in two DN-S3000s.

•Connect the X-EFFECT IN/OUT terminals between two DN-S3000s.

q, w

Start Relay Play

Play and Cue

•When the !0CUE button is pushed during playback, the track stops and returns to the position that current playback started (Cue point) and prepares for next playback. This function is called Back-Cue. With Back-Cue function, you can start from exactly same position. The !0CUE button illuminates solid red when DN-S3000 is ready to start playback.

•You can set and change Cue point as follows.

•When you started playback.

•Track select finished.

•manual search.

!Move the Cue point

•If you would not like to start playback from beginning of the track, you need to move Cue Point using fast Search and manual search function.

You can move to the approximate playback start position by #1or #2FAST SEARCH buttons.

[1-MIN.SKIP]

•If the FAST SEARCH button

is pushed short time, the

Adjusting the pitch

•With Pitch slider you can adjust the playback speed (Pitch).

•If you would not prefer to change key of sound, use the Key Adjust function.

Push the #6 PITCH/KEY button to PITCH LED lights up.

•PITCH → KEY (key adjust) → OFF

Pitch decreases

Move the #5Pitch slider to adjust

2the pitch. The current pitch setting is displayed on the display.

Pitch increases

DN-S3000 has five pitch ranges, 4%, 10%, 16%, 24% 50% and 100%. When the #6 RANGE

PLATTER in the direction in which the Platter

is turning.

[Scratch Disc]

•When the Scratch mode is

	set to SEARCH, the playback
	speed can be changed by
3	turning !1Scratch Disc
3	during playback.

•The pitch increases gradually when the Scratch Disc is turned clockwise and decreases when turned counterclockwise.

•When you stop turning the Scratch Disc, the playing speed returns to the previous pitch.

Select the track

•Turn the #0TRACK knob.

•By pushing #0TRACK knob down while turning, the tracks will change 10 at a time.

q Push the RELAY button for more than 1 sec to enable Relay play mode. You can set Relay mode as below.

•In the single play mode, when the one player’s playback reaches end of track, another DN-S3000 starts playing.

1• In the continuous play mode, when the whole tracks on one side are finished, another DN-S3000 starts.

•The discs in two DN-S3000s can be played alternately by setting both DN- S3000 to the relay play mode.

•Relay play can be set in the program and random play modes.

•Relay play is possible also for DN-S3000 or DN-S5000.

		Stop Relay Play
		w When the RELAY button
	2	is pushed for more than 1
	2	sec while in the relay play
		sec while in the relay play
		mode, the relay play
		mode is turned off.

1	playback position skips for about 1 minute.

[FAST SEARCH]

• When the FAST SEARCH button is pressed and held in, the disc is fast-searched.

3 button is pushed for more than 1 sec, the pitch range can be selected with the #0 PARAMETERS knob.

Power on play

•When “POWER ON PLAY” is set to “ON” at “⁄4 PRESET (8)”, playback starts from the first track on the disc when the power is turned on.