Denon DN-S3000 manual Specifications, Replacing the Belt, General, Audio Section, Functions

ENGLISH

15SPECIFICATIONS

GENERAL
Type:	Compact disc player
Disc type:	Standard compact discs (12 cm discs), CD-TEXT
	CD-R, CD-RW discs

16REPLACING THE BELT

•On the DN-S3000, the platter is driven by a belt. In the unlikely case of trouble, use the procedure described below to replace the belt.

	NOTE: Finalized CD-R or CD-RW discs can be played back in this unit.
	However, according to recording quality, some CD-R/RW discs
	cannot be played.
Dimensions:	Player unit:		285 (W) x 111.5 (H) x 327 (D) mm (without feet)
			11-7/32” (W) x 4-25/64” (H) x 12-7/8” (D)
Installation:	Table top type
Mass:	Player unit:		6.0 kg (12 lbs 9 oz)
Power supply:	U.S.A., Canada and Taiwan R.O.C. models: 120 V AC					±10%, 60 Hz
	European models:				230 V AC	±10%, 50 Hz
Power consumption:	16 W
Environmental conditions:	Operational temperature:		5 to 35°C	(41 to 95°F)
	Operational humidity:		25 to 85%	(no condensation)
	Storage temperature:		–20 to 60°C	(4 to 140°F)
AUDIO SECTION
Main out, Monitor out
Quantization:	24-bit linear per channel
Sampling frequency:	44.1 kHz at normal pitch
Oversampling rate:	8 times
Total harmonic distortion:	0.01% or less
Signal to noise ratio:	90 dB or more
Channel separation:	85 dB or more
Frequency response:	20 to 20,000 Hz
Analog output
Output level:	2.0 V r.m.s.
Load impedance:	10 kΩ/kohms or more
Digital output
Signal format:	IEC958-Type II
Output level:	0.5 Vp-p 75 Ω/ohms
FUNCTIONS
Instant start:	Within 20 msec.
Variable pitch:	±4% (0.02% pitch),	±10% (0.1% pitch),			±16% (0.1% pitch)
	±24% (0.1% pitch),	±50% (0.5% pitch)			±100% (1.0% pitch)
Pitch bend:	Pitch range ±32%
	Pitch range ±100%:		±99%
Sampler
Sampling:	44.1 kHz
Length:	15 sec.
Output level:	2.0 V r.m.s. (Variable / -14 ~ +6 dB)
Variable pitch:	±24% (0.1% pitch)
Search precision:	1/75 sec. (1 subcode frame)
Max. scan speed:	Over 20 times normal speed
Max. MEMO memory steps:	5000 steps

✽Specifications and design are subject to change without notice for purpose of improvement.

1.Remove a screw A (Hexagon socket head) and pull out Scratch Disc and Slip Mat.

(Hexagon socket head) A

2. Remove Belt from Motor Pully.

Belt

Motor Pully

3.Remove 3 screws B (< head) and pull out Platter.

(< head) B

4. Remove Belt from Platter.

Platter

Belt

5. Mount in the order 4 → 1.

CAUTIONS:

•Unplug the power cord before replacing the belt.

•Do not touch the sensor or scale(∗) when removing the Platter.

•Do not apply oil or grease to the belt when replacing it.

Stabilizer

Scratch Disc

Slip Mat

Slip Sheet

B(< head)

Platter

∗

20