10SAMPLER
q, r,
i, !0!0 w, o y, u
e, t !1, !3 !4, !6
!2, !5
Exit and Reloop |
|
|
| |
6 u The EXIT/RELOOP button |
|
|
| |
| can be used same as |
|
|
|
| Seamless Loop function. |
|
|
|
|
|
|
| |
Reverse Play |
|
|
| |
i | You can play the Sampled | RVS | ||
|
|
| ||
| sound in reverse by pushing |
|
|
|
| the RVS button. In reverse play |
|
|
|
7mode RVS LED lights up.
•Reverse playback will take affect when you push the SAMP button after reverse mode has been turned on. To return to normal forward playback, push the RVS button once again.
Moving Sampler B point |
o When the B button is |
ENGLISH
Adjust pitch
The Sampler playback pitch can be adjustable.
!1Push the SAMP.PITCH button, the pitch input mode is set, PARAMETERS LED flashes and the current settings are displayed on the character display.
•Start Sampler playback.
!2Turning the PARAMETERS knob can change the pitch.
✽When pushing down and turning the
PARAMETERS knob, you can change the pitch range 10 times faster.
!3Push the SAMP.PITCH button again to turn the pitch input mode off.
Adjust sound level
The Sampler playback sound level can be adjustable.
Record in Sampler
qWhen the SAMP button is
| pushed in the standby or | SAMP. |
| playing, the sound from |
|
1 | SAMP point is recorded to |
|
Sampler memory up to 15 |
| |
| seconds. |
|
| • The SAMP button is flashing while | |
| recording. When the | recording is |
| completed, the button turns off and the | |
| corresponding SAMP B LED lights up. | |
Setting B point
wWhen the B button is
pushed during Sampler recording, the Sampler Loop B point is set and the loop mode turns on.
2• Recording continues for approximately 15 seconds without stopping after set B point.
•If the B point is not set, recording end point set as B point automatically. Also EXIT/RELOOP LED light to indicates Sampler Loop mode is set automatically.
Stop recording
eTo stop recording before
| recording finish | STOP |
3 | automatically with |
|
| memory full, push the |
|
| STOP button. |
|
•The EXIT/RELOOP LED light to indicates Sampler Loop mode is set automatically.
Play Sampler sound |
|
r Playback of the Sampler | SAMP. |
sound starts when the |
|
SAMP button is pushed after |
|
recording has stopped. |
|
•Sampler playback continues in looping. With setting B point, playback loop between A and B point. Without B point
4setting Sampler loops whole recorded length (about 15 seconds).
t To stop the Sampler |
|
sound push STOP button. | STOP |
| Select Sampler Loop mode | ||
| You can select loop mode for Sampler when | ||
| Sampler playback stop. | ||
| Loop (default): | ||
| Sampler playback continues with | ||
| looping. | ||
| (EXIT/RELOOP LED stays lit) | ||
5 | Exit: Sampler playback continues over B | ||
point up to recording length. | |||
| (EXIT/RELOOP LED flashes) | ||
| Single: Sampler playback stops at B point. | ||
| (EXIT/RELOOP LED turned off) | ||
| y To select loop mode, push |
|
|
|
| ||
| EXIT/RELOOP button after |
|
|
| recording and before playing. | ||
8 | pushed during Sampler |
playback, the B point moves | |
| to the point at which the |
| button was pushed, and loop |
| playback from point A starts. |
| Clearing the Sampler data |
|
| !0While pressing the RVS/(CLR) button, | |
| push the SAMP button to clear the | |
| Sampler. |
|
9 | RVS | SAMP. |
•Or, by pushing the RVS/(CLR) button for approx. 1 sec, you can clear Sampler.
!4Push the SAMP.VOL button, the sound level input mode is set, PARAMETERS LED flashes and the current settings are displayed on the character display.
•Start Sampler playback.
!5Turning the PARAMETERS knob can change the sound level.
!6Push the SAMP.VOL button again to turn the sound level input mode off.
15