!9(SAMP)EXIT/RELOOP
•Use this to turn the Sampler Loop mode on and off. Also acts as EXIT/RELOOP button for Sampler Loop to exit or back again.
@0A/B TRIM button
•With push of this button, the A and B point trim mode changes on and off while in PLAY or CUE mode.
@1(SAMP.) STOP button
•Push this button while in Sampler record or playback, Sampler record or playback stops.
@2TITLE button
•CD TEXT:
When there is CD text data, the CD text data is displayed when the button is pressed.
•MP3:
When an MP3 file has
@3 
CONT./SINGLE, 
RELAY button
•CONT./SINGLE:
Short pushing play ending mode between CONT (continue: play more tracks) and SINGLE (stop playing and ReCUE’s back to your set point).
•SINGLE PLAY LOCK:
SINGLE PLAY LOCK can be selected by PRESET(9). At this time , if this button is pushed, it will be selected. When SINGLE PLAY LOCK is selected, track selection during playback is disabled. This prevents playback from stopping when the Track Select Knob is turned accidentally during playback.Play ending mode is the same as single.
•RELAY:
You can turn on and off RELAY PLAY mode. Relay playback is possible when two DN- S3000s are connected by
@4 
TIME, T.TIME button
•TIME:
A short push will displays mode changes between ELAPSED TIME and REMAIN TIME.
•T.TIME:
A long push, will display mode changes between TRACK TIME and DISC TIME.
•So, you can select display mode from four modes, TRACK ELAPSED, TRACK REMAIN, DISC ELAPSED and DISC REMAIN.
@5 
MEMO, 
PRESET button
•MEMO:
The memo mode starts when this button is pushed once in the Cue mode.
•PRESET:
When this button is pushed for more than 1 sec, the PRESET mode menu is displayed.
@6(SAMP) PITCH button
•Push this button, pitch of Sampler can be adjusted with the PARAMETERS knob.
@7(SAMP) VOL. button
•Push this button, output level of Sampler playback can be adjusted with the PARAMETERS knob.
@8NEXT TRACK button
•If this button is pushed during playback, the NEXT TRACK mode will be selected. The next track can be selected with the PARAMETERS knob.
@9SCRATCH MODE, 
SEARCH button
Select the source for Scratch playback and the manual search/bend mode.
•MAIN:
This button lights up or blinks at orange. Manipulate Main Track sound
•SAMP.:
This button lights up or blinks at green. Manipulate Sampler Track sound
•SEARCH:
When this button is pushed for more than 1 sec, the SEARCH mode is selected.
When the Scratch Disc selector is set to SEARCH during playback, it works as the pitch bend function.
When Scratch Disc is turned in the pause or standby mode, works as the manual search function. Manual search works and you can move the CUE point around by one frame at a time (1/75 second) with an audible frame- repeat sound,
#0TRACK/PARAMETERS knob
•TRACK:
When PARAMETERS LED is on, turn this knob to select tracks.
By pushing this knob down while turning, the tracks will change by 10 tracks at a time.
•PARAMETERS:
When the PARAMETER LED is flashing, turn this knob to select and change the parameter for items found in the Platter effects, Memo, and Preset data, etc.
ENGLISH
#1FAST SEARCH (6),
#2FAST SEARCH (7)
•1-MIN.SKIP:
When one of these buttons is short pushed, the playback position skips approximately 1 minute in the forward (6) or reverse (7) direction.
•FAST SEARCH:
When one of these buttons is pressed and held in, the disc is
#3PITCH BEND – button
#4PITCH BEND + button
•Pushing these buttons will change main playing speed temporary.
•While pushing PITCH BEND + button playing speed increases and speed decreases while pushing PITCH BEND – button.
•When release button, playing speed returns to the previous speed.
#5Pitch Slider
•Use this slider to adjust playing speed.
•The playing speed decreases when slid upwards and increases downwards.
#6 
PITCH/KEY, 
RANGE button
•With this button you can select PITCH and KEY ADJUST mode. Mode changes Pitch on, Key Adjust on and both off cyclically. PITCH LED indicates in Pitch mode and KEY ADJUST indicator in the display lights up in Key Adjust mode.
•RANGE:
Push this button for more than 1 sec to select the pitch range. The pitch range can be selected with the PARAMETERS knob.
#7DUMP/RVS button
•Push this button to select between RVS or DUMP and OFF.
#8BRAKE button
•Push this button to set the BRAKE.
#9DRAG-S button
•Push this button to set the
9