Sunbeam EM6200 manual Programming your espresso machine, Programming Single Espresso

Page 19

Programming your espresso machine

The Espresso Vita has programming capabilities. Based on café settings the ‘SINGLE’ and ‘DOUBLE’ espresso functions are set at 30 and 60mls. However by following a few simple steps the coffee maker can personalise the espresso machine to achieve a serve of espresso to exactly how they like it.

Programming Single Espresso

1.To start programming the espresso machine needs to be in ‘STAND BY MODE’. So the machine is plugged in and switched on at the power point, but the machine itself is not powered on.

2.Prepare the filter handle. Fit the group handle with the single filter basket (12) and fill with finely ground coffee (14).

Using the coffee tamp supplied, tamp the coffee grinds (15). Secure the group handle to the group head (17)(18).

3.Place a cup under both pouring spouts (19).

4.To commence programming press and hold down both the ‘SINGLE’ and ‘DOUBLE’ espresso buttons while still holding down these buttons briefly press the ‘POWER’ button and release all buttons. The lights around the coffee buttons will start to slowly flash, dimming up and down.

5.Press the ‘SINGLE’ espresso button once to start the espresso pour.

6.Allow the espresso to pour until the desired level. Once the desired level is reached stop the espresso pour by pressing the ‘SINGLE’ espresso button. A long beep will signify that the new setting for the ‘SINGLE’ espresso operation has been programmed and stored into the machines memory.

7.The espresso machine will then go into ‘READY MODE’ and is ready to make espresso at the push of a button.

Programming Double Espresso

1.To start programming the espresso machine needs to be in ‘STAND BY MODE’. So the machine is plugged in and switched on at the power point, but the machine itself is not powered on.

2.Prepare the group handle. Fit the group handle with the double filter basket (12) and fill with finely ground coffee (14).

Using the coffee tamp supplied, tamp the coffee grinds (15). Secure the group handle to the group head (17)(18).

3.Place two cups under each pouring spout (19).

4.To commence programming press and hold down both the ‘SINGLE’ and ‘DOUBLE’ espresso buttons while still holding down these buttons briefly press the ‘POWER’ button and release all buttons. The lights around the coffee buttons will start to slowly flash, dimming up and down.

5.Press the ‘DOUBLE’ espresso button once to start the espresso pour.

6.Allow the espresso to pour until the desired level. Once the desired level is reached stop the espresso pour by pressing the ‘DOUBLE’ espresso button. A long beep will signify that the new setting for the ‘DOUBLE’ espresso operation has been programmed and stored into the machines memory.

7.The espresso machine will then go into ‘READY MODE’ and is ready to make espresso at the push of a button.

Resetting the Factory Settings

To revert back to the original factory settings;

1.Insert the power cord into a 230-240V AC power outlet and switch the power ‘ON’.

17

Image 19
Contents Espresso Vita Page Important instructions retain for future use ContentsSafety Precautions for Your Sunbeam Espresso Machine Sunbeam’s Safety PrecautionsAbout espresso coffee Push button control panel Features of your Sunbeam Espresso VitaWater level indicator Warming plateSteam and hot water control dial 5L water reservoir 600ml jug Cleaning toolEspresso gauge Programmable control panelThermoblock Heating System Bar PumpCrema System Optimum Pour Under Over Extracted Features of your Sunbeam Espresso VitaManual Using the control panelPower Ready ModeDouble Espresso Using the control panelSteam Programming the Single or Double poursHot Water Unit on Use. Ready Mode Warming the espresso cups Reference guide to using your espresso machineMaking the espresso Reference guide to using your espresso machinePlace group handle onto group head Texturing milk Press the Steam button to activate steam modeTurn off steam by turning dial clockwise Swing steam wand to the side of espresso machine Cleaning Programming Double Espresso Resetting the Factory SettingsProgramming your espresso machine Programming Single EspressoProgramming your espresso machine Preparing your espresso machine before use Dosing and Tamping Guide to the perfect espressoPreheat Glasses Preheat Group Handle and Filter BasketCaring for your Espresso Machine Eco Mode and Standby ModeGuide to the perfect espresso Pre-InfusionGuide to milk texturing Guide to milk texturing Using the hot water function190mL cup Hot water to taste Single or double espresso Espresso RecipesCaffe Latte Espresso RecipesGroup head rubber seal Care and CleaningDrip tray and grill Group head, group handle & filter basketsCup warming plate and exterior Care and CleaningSteam wand Descaling Descaling solutionDescaling the espresso machine Descaling Press and hold down the ‘MANUAL’ button Espresso Thermoblock TemperaturePlease refer to the chart below Steam Thermoblock TemperaturePress and hold down the ‘HOT WATER/ STEAM’ button Steam Pump Rate Programming Steam Wetness or Steam Pump RateSteam thermoblock temperatures and the steam pump rate Factory ResetAdvanced Programming Options No coffee runs through Trouble shooting guideProblem Possible cause What to do Group handleCoffee is too cold Trouble shooting guideEspresso tastes burnt Uneven cup fillingLoad noise Australia Month Replacement GuaranteeNew Zealand Need help with your appliance?

EM6200 specifications

The Sunbeam EM6200 is a versatile and stylish espresso machine designed for coffee enthusiasts who value both performance and aesthetics. This compact unit combines advanced features with user-friendly operation, making it an ideal choice for home baristas and casual coffee drinkers alike.

One of the standout features of the Sunbeam EM6200 is its powerful 15-bar Italian pump, which ensures optimal pressure for extracting rich, flavorful espresso shots. This high pressure is crucial for producing a perfect crema, delivering a café-quality experience right in the comfort of your kitchen. The machine heats up quickly thanks to its stainless steel boiler, enabling users to brew in just a short time without sacrificing quality.

In terms of user interface, the EM6200 is equipped with a combination of manual controls and an easy-to-read LCD display. This allows users to select from various coffee options, adjust the coffee strength, and customize their brewing experience. The intuitive layout ensures that even beginners can enjoy a seamless brewing process.

The Sunbeam EM6200 also features a built-in steam wand for frothing milk. This allows users to create creamy lattes, cappuccinos, and macchiatos with ease. The steam wand is designed with a 360-degree rotation, providing flexibility in frothing techniques and simplifying the milk texturing process.

For coffee aficionados looking for flexibility, the EM6200 supports both ground coffee and E.S.E. pods. This versatility ensures that users can enjoy their favorite coffee varieties while also having the convenience of pre-packaged options. The machine comes with a removable drip tray and water reservoir, making cleanup and maintenance a breeze.

Additional attributes of the Sunbeam EM6200 include its sleek design, available in various finishes, which enhances any kitchen decor. The machine is also equipped with safety features such as an automatic shutdown, giving users peace of mind during use.

Overall, the Sunbeam EM6200 is a well-rounded espresso machine that combines modern technology with practical features. Its combination of functionality, ease of use, and elegant design makes it a popular choice for coffee lovers seeking to elevate their home brewing experience. Whether you are a novice or an experienced barista, the EM6200 is equipped to help you craft the perfect cup of coffee every time.