Wells OC-2HG operation manual Equipment SET-UP, Installing Legs, Installing Optional Casters

Page 8

INSTALLATION (continued)

WARNING:

ELECTRIC

SHOCK HAZARD

All servicing requiring access to non-insulated electrical components must be performed by a factory authorized technician.

DO NOT open any access panel which requires the use of tools. Failure to follow this warning can result in severe electrical shock.

NOTE: Oven is shipped with biscuit baking adapter plate attached to rear panel.

If oven is used exclusively for bread products (bread, pies, etc.), DO NOT remove this adapter.

Optional Venting Kit #23035 is available to allow cooking protein products. If oven is used for proteins, remove adapter and install the external vent. When cooking protein, additional venting is required to decrease release of cooking vapors when opening the door.

EQUIPMENT SET-UP

1.CURB or COUNTER MOUNTING

a.Setup the appliance only on a firm, level, non-combustible surface. Verify local codes for requirements. Concrete, tile, terrazzo or metal surfaces are recommended. Metal over combustible material may not meet code for non-combustible surfaces.

b.Appliance is approved for installation with zero clearance at bottom.

c.Recommend at least 3” clearance on sides and back to allow adequate air flow.

2.INSTALLING LEGS

a.Install adjustable legs, one on each corner of the appliance, in the holes provided.

b.Set up the appliance only on a firm, level, non-combustible surface. Verify local codes for requirements. Concrete, tile, terrazzo or metal surfaces are recommended. Metal over combustible material may not meet code for non-combustible surfaces.

c.LEVELING: Verify that the appliance sits firmly ON ALL FOUR LEGS. With a spirit level, check that the appliance is level front-to-back and side-to-side.

3.INSTALLING OPTIONAL CASTERS

a.Install casters, one on each corner of the appliance, in the holes provided. Locking casters must be installed on the FRONT of the appliance.

b.Set up the appliance only on a firm, level, non-combustible surface. Verify local codes for requirements. Concrete, tile, terrazzo or metal surfaces are recommended. Metal over combustible material may not meet code for non-combustible surfaces.

c.LEVELING: Verify that the appliance sits firmly on all four casters when in its normal operational position. With a spirit level, check that the appliance is level front-to-back and side-to-side.

272 304621 Operation Manual for OC-2HG Convection

Optional Vent Duct Installation

6

Oven/Combo Cook Center

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Model OC-2HG Important do not Discard this ManualLimited Warranty Statement Introduction Table of ContentsSpecifications Features & Operating Controls Description Function Precautions and General Information Agency Listing InformationElectric Shock Hazard HOT SurfaceInstallation Service Technician Installation NotesUnpacking & Inspection Risk of Personal InjuryEquipment SET-UP Installing LegsInstalling Optional Casters Electrical Shock Hazard Electrical Connections Must be Made by aRisk Damage Operation Suggested Cooking TimesConvection Oven Product Temp Time Number Minutes RacksOperation Manual Cook Mode Program Cook ModeTemperature Offset Mode Convection Oven Operating InstructionsOperation Griddle Operating Instructions Operation Hotplate Operating InstructionsOven Cleaning Instructions Daily CleaningFrequency ToolsWeekly Cleaning Griddle Cleaning Instructions Important Never USE Steel Wool to Clean the Griddle SurfaceDuring USE Griddle ExteriorHotplate Cleaning Instructions Preventative Maintenance PrecautionsTroubleshooting Suggestions Symptom Possible Cause Suggested RemedyError Codes FANExploded View and Parts List Exploded View and Parts List Exploded View and Parts List Grommet 7/8 O.D Exploded View and Parts List ASSY, Cavity Terminal BLOCK, 3 Pole Wiring Diagram Venting KIT Used When Cooking Protein DescriptionOven Stacking KIT Prep TOP

OC-2HG specifications

The Wells OC-2HG is a sophisticated piece of equipment designed to meet the demands of modern commercial and industrial applications. This innovative unit integrates advanced technologies to enhance efficiency, productivity, and sustainability. One of the standout features of the OC-2HG is its compact design, which allows for easy installation in various settings without requiring extensive modifications to existing infrastructure.

At the core of the OC-2HG is a high-performance engine that boasts low emissions and reduced noise levels, making it suitable for use in urban environments. This is complemented by an intelligent power management system that optimizes fuel consumption and ensures that the device operates at peak efficiency, ultimately lowering operational costs. Additionally, the unit is equipped with a cutting-edge digital control panel that provides real-time monitoring and diagnostics, allowing operators to track performance metrics and quickly address any potential issues.

The OC-2HG also features an advanced cooling system that enhances reliability and extends the lifespan of critical components. This technology allows the unit to operate effectively in a variety of temperature conditions, ensuring consistent performance regardless of environmental factors. Furthermore, the equipment is built with durable materials that withstand the rigors of daily use while minimizing maintenance needs.

Safety is a top priority in the design of the Wells OC-2HG. The unit is equipped with multiple safety features, including automated shut-off mechanisms and emergency stop functions, which help protect both operators and surrounding personnel.

Another notable characteristic of the OC-2HG is its versatility. It can be adapted for a wide range of applications, from construction sites to energy production facilities. This adaptability is supported by a selection of interchangeable accessories and configurations, allowing users to configure the equipment to suit their specific needs.

In conclusion, the Wells OC-2HG combines cutting-edge technology with an emphasis on safety and efficiency. With its compact design, advanced engine, intelligent monitoring systems, and versatility, it stands out as a premier choice in the market for those looking to enhance their operational capabilities while reducing their environmental impact. Whether for industrial or commercial use, the OC-2HG is undeniably equipped to deliver superior performance and reliability.
Top Page Image Contents