Xantech mrc88 RS232 Settings, Monitor Lockout Mode Factory default Disabled

Page 65

Model MRC88

Page: 65

RS232 SETTINGS

To configure the settings of the RS232 Port located in the rear of the MRC88 Controller/Amplifier Figure 3- (29), click on the CHANGE SETTINGS button under the RS232 Settings section of the CONTROLLER tab. This will display all configurable settings for the RS232 control port. See Figure - 34 below for reference.

Figure 34 - RS232 Port Default Settings

BAUD RATE, DATA BITS, STOP BITS AMD PARITY SETTINGS

To change Baud Rate, Data Bits, Stop Bits or Parity settings, click on the corresponding to access the drop-down menu and click on the desired setting. Default settings for all are shown above in Figure 34.

PROCESS RS232 INPUT

(Factory Default = “ENABLED”)

This setting should be enabled when the RS232 port will be used to receive data to control the MRC88 System from a PC or other RS232 device. If the RS232 port will only be used to control an external device from the Keypad (thermostat controller, lighting system etc..), disable this setting to prevent the MRC88 system from misinterpreting erroneous data.

NOTE:To control the MRC88 System from the RS232 port, please see Section 5: RS232 Input Translator and Section 9: Appendix-RS232 Control.

MONITOR LOCKOUT MODE (Factory default: “DISABLED”)

This mode is only accessible if ‘Priority Lockout’ is enabled. If Priority Lockout is not selected (system is in Whole House Mode), the Monitor Lockout Boxes are grayed out and therefore cannot be selected. Once the boxes are accessible, checking the corresponding boxes prevents sources from being monitored (audio and video) and controlled in specific zones. Example: If adult content is not to go to the children’s areas, this can be set at the time of system installation. When a Source is selected in a zone that is checked, a message stating MONITOR LOCKOUT will be displayed in the zones keypad LCD window and now video and/or audio for that source will not be able to be monitored. To enable MONITOR LOCKOUT for a particular Zone/Source complete the following instructions:

1.Select “PRIORITY LOCKOUT MODE” under MODE OF OPERATION. The Monitor Lockout boxes will be activated.

2.By Zone, click in the box of each Source that is NOT to be monitored in that zone.

© 2003 Xantech Corporation

Image 65
Contents Installation Instructions Not Expose this Appliance to Rain or Moisture Safety Instructions Read Before Operating EquipmentTable of Contents Programming the Controller ADVANCED/EXPANDED Programming Section Model MRC88 Xantech Corporation MRC88 system includes the following components General InformationModel MRC88 System Overview System Block DiagramCONTROLLER/AMPLIFIER Features Keypad Features MRC88 Front Panel Features and Connections MRC88 CONTROLLER/AMPLIFIER Panel and Feature DescriptionsSystem Status Power-Up Mode Front PanelZone Status Active-Operational Mode Source Component Input Connections MRC88 Rear Panel Features and ConnectionsSource Loop-Thru Connections MRC88 Keypad MRC88 Keypad Feature DescriptionsMRC88 Keypad Front Features Model MRC88 MRC88 Keypad Rear Features and Connections Model MRC88 Keypad Rear Panel Features and FunctionsOperation OUT-OF-THE-BOX PRE Test BASIC/ADVANCED/EXPANDED InstallationObstructions MRC88Keep perforations on top cover free Expanded Mounting and Installing the MRC88 KeypadMRC88 Keypad mounting template MRC88 Keypad Removal Optional Keypad Back-Box for pre-install applicationsAudio Connections Connecting the MRC88 CONTROLLER/AMPLIFIERBASIC/ADVANCED Video ConnectionsAdvanced CSM1 Threshold AdjustmentsBASIC/ADVANCED/EXPANDED Zone Related Wiring ConnectionsStatus BASIC/ADVANCED/EXPANDED Composite VideoModulated Video CO1 and CO2 Zones 7 Control OutZone IR BASIC/ADVANCED/EXPANDED Connections AT the Zone Location BASIC/ADVANCED/EXPANDEDMultiple Keypad Connections Single Keypad CAT5 ConnectionsOFF Zone Expansion Connecting TWO MRC88 Controllers ExpandedLinking TWO MRC88 CONTROLLER/AMPLIFIER Units MRC88 Keypad CAT5 Cable Lengths MRC88 Connecting Block located on rear of KeypadBASIC/ADVANCED/EXPANDED Typical MRC88 System SETTING-UP the MRC88 SystemPre-Programming the MRC88 BASIC/ADVANCED/EXPANDED Computer Requirements Minimum Basic Mode Advanced Mode Expanded ModePlanning the System Software Installation Connecting the MRC88 CONTROLLER/AMPLIFIER to the PCIncluded Hardware & Software Items Starting MRC88 Dragon DROP-IR SoftwareStarting a Project BUILT-IN IR Code Library BASIC/ADVANCED/EXPANDED Learning IR Commands Creating Palette FilesLearning IR Commands BASIC/ADVANCED/EXPANDED Built-In Mfg’s IR Command LibraryRecording Toggle Command Functions Creating a Palette File BASIC/ADVANCED/EXPANDED To Rename an Existing FunctionTo Add a New Function Importing CCF Files Getting Source Commands from the InternetEditing BRAND, COMPONENT, and Function Lists Importing Discrete IR Hex Codes ADVANCED/EXPANDED Entering RS232 Command StringsRS232 Palette Editor Window Using PC TestUsing MRC88 Test Creating an RS232 Palette File Creating AN RS232 Palette File ADVANCED/EXPANDEDProgramming The Controller Configuring Source Icons on MRC88 Keypad LCDDownloading Source Icons to the Keypad Creating NEW IconsSelecting Icons from the Icon Generator Selecting RS232 Command Palettes ADVANCED/EXPANDED Placing Commands Onto the Virtual KeypadSelecting Internal Amplifier Commands ADVANCED/EXPANDED Placing Commands on the Virtual Keypad BasicProgramming Sequences Macros Editing Buttons on the Virtual Keypad Button Edit Pop-Up MenuEditing Commands in the Macro Command List Window Zone 1 thru Editing CommandsProgramming Power Management Programming Power Management and Sense Trigger CodesBasic Power Management Programming Sense Triggers Programming Sense Trigger Codes ADVANCED/EXPANDEDTesting Commands Under Power Management and Sense Triggers Default settings set in Basic Mode are as follows Zone Options ConfigurationName of Zone ADVANCED/EXPANDED RC68 Code GroupIR Loop Back Settings ADVANCED/EXPANDED PRE AMP Volume Adjust Settings ADVANCED/EXPANDEDTransferring the Project Configuring Commands for IR in ZoneZone Audio Input Controller Options ProgrammingIR Routing Mode of OperationBACK-LIGHT Control Expanded OptionsMonitor Lockout Mode Factory default Disabled RS232 SettingsMonitor Lockout Mode Zone Linking Programming Dynamic Zone Link Mode Factory default Disabled Link ALL Dynamic RS232 Input TranslatorLink ALL Static Clear ALLIRS232 Input Translator Programming IR Commands and SequencesRC68+ IR Code Triggered Sequencer RC68 IR Command Macro WindowInternal Amplifier Command Window Programming Internal Amplifier CommandsUsing Internal Amplifier Commands Internal Amplifier Commands Zone Expansion Connecting Multiple MRC88 ControllersEnabling Expanded Mode Programming in Expanded ModePhysical Connections in Expanded Mode RS232 Control While in Expanded ModeSources 1 through Uploading MRC88 Projects Transferring a Project to the MRC88Saving and BACKING-UP Files Warm Firmware Upgrade Firmware Upgrade OptionisCold Firmware Upgrade Downloading Firmware Files from the WEBTeaching a HAND-HELD Remote to Operate the MRC88 System Tweaking the SystemTrimming Source Audio Input Levels Making Fine AdjustmentsKeypad Adjustments Zone AdjustmentsSetting the Volume Powering the Zone on and OFFAccessing Tier 2 Commands Source Slection and ControlAudio Adjustments BASIC/ADVANCED/EXPANDED Zone SettingsSystem Status BASIC/ADVANCED Dynamic Monitor Lockout Parental Control ADVANCED/EXPANDEDExpanded RS232 Control ?5SS3+ 7PR1+?5SS+ AO+ CommandsQueries Volume Level 39 Steps Keypad Button ID Level in dB MRC88 Setting+14 +12Balance Level Left Speaker Right Speaker MRC88 Setting AttenuationProblem Probable Cause and Solution TroubleshootingModel MRC88Page 96Model MRC88 RS232 and Expansion PIN OUT Information GND Certifications SpecificationsVideo IR SensorModel MRC88 Model MRC88 Xantech Corporation Bradley Avenue, Sylmar CA Phone 818.362.0353 fax Xantech Corporation
Related manuals
Manual 102 pages 31.66 Kb Manual 12 pages 21.17 Kb