Xantech MRC44 Internal Amplifier Commands, Command Name Command List Name Parameter

Page 40

Page: 40

Model MRC44

1.In the MRC44 System Window Menu, click on Palette, and select “MRC44 Amplifier Command Generator” (F6).

2.From the MRC44 System Window, select the Zone to be programmed. (e.g. Zone 1)

3.Click the button to be programmed. (e.g. “Power”)

4.Select the command to be used (e.g. “Zone Source Select Command) from the pull-down list in the Amplifier Internal Command Setup window.

5.Two Parameter boxes will appear as shown in Figure 23, to set the action of the command. (e.g. Zone 1 and Source 1).

6.A table of MRC44 Controller/Amplifier commands is shown in Table 2 below with the associated controls.

7.Click “ACCEPT” when the Internal Amplifier Command is set to the desired state.

8.The command will automatically be placed in the command list of the Zone/Button selected. (In this example when the Zone 1 “POWER” button is pressed, and the zone is OFF, the zone will turn ON, Source 1 will automatically be selected and by adding a “PLAY” command for a CD player to the sequence, Zone 1 will always default to CD when turned ON. Pressing the “POWER” button again will turn the zone “OFF”.

9.Repeat for all zones and commands as required.

(EXPANDED)

In the Expanded mode, Internal Amplifier Commands can only be programmed to ‘talk’ to the zones within either the Primary or Secondary Controllers. Internal Amplifier Commands are not communicated from one controller to the other. The one exception is the “Turn Off All Zones Command” which will turn all zones OFF.

Command Name

Command List Name

Parameter 1

Parameter 2

Zone Power Command

"MRC44 ZnePwr"

Zone (1-4) (5-8)

PwrState (On, Off)

Zone Toggle Power Command

"MRC44 TogZnePwr"

Zone (1-4) (5-8)

N/A

Zone Volume Level Command

"MRC44 ZneVol"

Zone (1-4) (5-8)

VolLevel (0 – 63)

Zone Volume Step Up Command

"MRC44 ZneVol+"

Zone (1-4) (5-8)

N/A

Zone Volume Step Down Command

"MRC44 ZneVol-"

Zone (1-4) (5-8)

N/A

Zone Balance Level Command

"MRC44 ZneBal"

Zone (1-4) (5-8)

BalLevel (-15-15)

Zone Balance Step Up Command

"MRC44 ZneBal+"

Zone (1-4) (5-8)

N/A

Zone Balance Step Down Command

"MRC44 ZneBal-"

Zone (1-4) (5-8)

N/A

Zone Treble Level Command

"MRC44 ZneTreb"

Zone (1-4) (5-8)

TrebLevel (-14dB-14dB)

Zone Treble Step Up Command

"MRC44 ZneTreb+"

Zone (1-4) (5-8)

N/A

Zone Treble Step Down Command

"MRC44 ZneTreb-"

Zone (1-4) (5-8)

N/A

Zone Bass Level Command

"MRC44 ZneBass"

Zone (1-4) (5-8)

BassLevel (-14dB-14dB)

Zone Bass Step Up Command

"MRC44 ZneBass+"

Zone (1-4) (5-8)

N/A

Zone Bass Step Down Command

"MRC44 ZneBass-"

Zone (1-4) (5-8)

N/A

Zone Source Select Command

"MRC44 ZneSrcSel"

Zone (1-4) (5-8)

Source (1-4)

Zone Mute State Command

"MRC44 ZneMute"

Zone (1-4) (5-8)

MuteState (On, Off)

Zone Mute Toggle Command

"MRC44 ZneTogMute"

Zone (1-4) (5-8)

N/A

Zone Set Control Status Command

"MRC44 ZneCtlStat"

Zone (1-4) (5-8)

CtrlState (On, Off)

Zone Restore Balance Command

"MRC44 ZneResBal"

Zone (1-4) (5-8)

N/A

Zone Restore Treble Command

"MRC44 ZneRestTreb"

Zone (1-4) (5-8)

N/A

Zone Restore Bass Command

"MRC44 ZneRestBass"

Zone (1-4) (5-8)

N/A

Zone Start Z Adjust Command

"MRC44 ZneStrtZAdj"

Zone (1-4) (5-8)

N/A

Zone Set Max V Command

"MRC44 ZneMaxV"

Zone (1-4) (5-8)

N/A

Zone Adjust Done Command

"MRC44 ZneAdjDone"

Zone (1-4) (5-8)

N/A

Zone Start Trim Adjust Command

"MRC44 ZneStrtTrim"

Zone (1-4) (5-8)

N/A

Turn Off All Zones Command

“MRC44 ZneAllOff”

N/A

N/A

Table 2 – Internal Amplifier Commands

© 2002 Xantech Corporation

Page 39 Page 41
Image 40
Page 39 Page 41
Contents Installation Instructions Safety Instructions Read Before Operating Equipment Not Expose this Appliance to Rain or MoistureTable of Contents General Information System Block Diagram System OverviewCONTROLLER/AMPLIFIER Features Keypad FeaturesSystem Status Power-Up Mode MRC44 CONTROLLER/AMPLIFIER Panel and Feature DescriptionsZone Status Operational Mode Source Component Connections 8Model MRC44Model MRC44 MRC44 Keypad Feature Descriptions Model MRC44 Keypad Front Panel Features and FunctionsModel MRC44 Keypad Rear Panel Features and Functions Operation OUT-OF-THE-BOX BASIC/ADVANCED/EXPANDED Installation ExpandedCutting the hole MRC44 Keypad mounting templateInstalling the Mounting Bracket MRC44 Keypad RemovalConnecting the MRC44 CONTROLLER/AMPLIFIER BASIC/ADVANCEDBASIC/ADVANCED/EXPANDED Zone Wiring Connections at the MRC44 Controller/AmplifierSpeaker Connections Video Connections BASIC/ADVANCED/EXPANDED Composite Video Modulated VideoControl Out and Status Connections Status Control OutConnections AT the Zone Location BASIC/ADVANCED/EXPANDED OFFExtended Runs and Secondary Keypad In Zone MRC44 Keypad CAT5 Cable LengthsSETTING-UP the MRC44 System For setup of an expanded system, see FigureZone Programming the MRC44 System Using the DRAG450MRC Software Software InstallationPlanning the System Included Hardware & Software ItemsLearning IR Commands Toggle Command FunctionStarting MRC44 Dragon Drop-IR Serial Port SelectionEditing and Testing IR Commands Creating PalettesAdding Brands Adding Components and FunctionsPutting Codes to Work in the MRC44 Programming Keypads BasicDRAG450MRC Basic System Window AdvancedMRC44 Keypad LCD Icon Generator Placing Commands On The Virtual Keypad Basic Creating New IconsSelecting Palettes ADVANCED/EXPANDEDTimed Delays Repeat CommandsPush & Hold Tiered Commands Editing SequencesSystem SET-UP Procedures Programming the MRC44 CONTROLLER/AMPLIFIER Programming Power Management and Sense Trigger Codes Basic Video Sensing Power ManagementCurrent Sensing Power Management Sense Inputs Video Sensing Sense TriggerCurrent Sense De-Bounce Settings ADVANCED/EXPANDED ProgrammingPolarity of Sense Input Transferring The Project BasicIR Output Intensity Settings Expanded Options Zone LinkingFirmware Upgrade Options RC68+ IR Code Triggered Sequencer Programming Internal Amplifier Commands Internal Amplifier Command WindowInternal Amplifier Commands Command Name Command List Name ParameterTransferring a Project to the MRC44 BASIC/ADVANCED Uploading MRC44 ProjectsSaving and BACKING-UP Files Automatic SaveUsing Backup Files Fine TuningAdjusting Input Level Trim Backing-Up Project FilesIR Sensitivity Adjustment Zone AdjustmentsLCD Backlight Adjustment Audio Adjustments Operating InstructionsZone Control System StatusDynamic Zone Link Advanced Zone Expansion Using Multiple MRC44 Controllers Source A/V Distribution and Power ManagementAV61 Connections Combining IR OutputsExpanded System Diagram Troubleshooting Problem Probable Cause and SolutionModel MRC44Page 50Model MRC44 Problem Probable Cause and Solution Certifications SpecificationsXantech Corporation
Related manuals
Manual 12 pages 21.17 Kb
Top Page Image Contents