Jenn-Air W10430955A installation instructions Bare Wire Torque Specifications, Wire Awg Torque

Page 18

3.Pull the conduit through the strain relief on cord/conduit plate on bottom of range. Allow enough slack to easily attach wiring to the terminal block.

A

B

 

C

G

D

 

F

E

 

A. Terminal block

E. Neutral (white) wire

B. Ground-link screw

F. Line 1 (black) wire

C. Cord/conduit plate

G. Bare (green) ground wire

D. Line 2 (red) wire

 

4.Attach terminal lugs to line 1 (black), neutral (white), and line 2 (red) wires. Loosen (do not remove) the setscrew on the front of the terminal lug and insert exposed wire end through bottom of terminal lugs. Securely tighten set screw to torque as shown in the following Bare Wire Torque Specifications chart.

A

B

C D E

A. Terminal lug

D. Neutral (white) wire

B. Setscrew

E. Line 2 (red) wire

C. Line 1 (black) wire

 

Bare Wire Torque Specifications

Attaching terminal lugs to the terminal block - 20 lbs-in. (2.3 N-m)

Wire Awg

Torque

8 gauge copper

25 lbs-in. (2.8 N-m)

 

 

6 gauge aluminum

35 lbs-in. (4.0 N-m)

 

 

5.Use Phillips screwdriver to connect the bare (green) ground wire to the range with the ground-link screw. The ground wire must be attached first and must not contact any other terminal.

6.Use ³⁄₈" nut driver to connect the neutral (white) wire to the center terminal block post with one of the 10–32 hex nuts.

G

A

B

 

 

F

 

D

E

C

 

 

 

A. 10–32 hex nut

E. Neutral (white) wire

B. Line 1 (black)

F. Line 2 (red)

C. Bare (green) ground wire

G. Terminal lug

D.Ground-link screw

7.Connect line 1 (black) and line 2 (red) wires to the outer terminal block posts with 10-32 hex nuts.

8.Securely tighten hex nuts.

9.Replace terminal block access cover.

3-wire connection: Direct Wire

Use this method only if local codes permit connecting ground conductor to neutral supply wire.

1.Pull the conduit through the hole and conduit plate on bottom of range. Allow enough slack to easily attach the wiring to the terminal block.

A

B

 

 

C

 

 

D

F

E

 

 

 

A. Terminal block

D. Line 2

(red) wire

B. Ground-link screw

E. Bare (green) ground wire

C. Cord/conduit plate

F. Line 1

(black) wire

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Table of Contents/Table des matières Range Safety Your safety and the safety of others are very importantInstallation Requirements Tools and PartsLocation Requirements Product Dimensions Cabinet Dimensions Wall Venting Venting RequirementsVenting Methods Floor VentingCalculating Vent System Length Concrete Slab Installations Exhaust Through WallConcrete Slab Installations Exhaust Through Window Well Left or Right Side VentingExample vent system If connecting to a 4-wire systemElectrical Requirements U.S.A. Only Electrical ConnectionIf connecting to a 3-wire system Electrical Requirements Canada OnlyCountertop Preparation Install Anti-Tip Bracket Installation InstructionsAdjust Leveling Legs Unpack RangeDetermine Equivalent Length of Vent System Install Downdraft SystemRear Wall Venting Floor Mounting Wall MountingTop View Top View View from Motor Side of Blower Power Supply Cord Direct Wire Style 1 Power supply cord strain reliefElectrical Connection U.S.A. Only Style 2 Direct wire strain relief Removable retaining nut Strain reliefWire connection Power Supply Cord Wire Connection Direct Wire Bare Wire Torque Specifications Wire Awg TorqueGauge copper Lbs-in .8 N-m Gauge aluminum Lbs-in .0 N-m Connect Range to Downdraft System Verify Anti-Tip Is Installed and Engaged Wall Venting Top View Side Venting left side venting shownFloor Venting Top View For power supply cord-connected ranges Complete InstallationIf you need Assistance or Service Moving the RangeFor direct-wired ranges Sécurité DE LA Cuisinière Votre sécurité et celle des autres est très importanteExigences D’INSTALLATION Exigences d’emplacementOutils et pièces Dimensions du placard Dimensions du produitPour obtenir des performances optimales Installations dans les régions au climat froidExigences concernant l’évacuation Air d’appointÉvacuation par le mur Installations sur dalle de béton Évacuation par le murMéthodes d’évacuation Évacuation par le plancherComposant Conduit de diamètre de 15,2 cm Coude à Calcul de la longueur effective du circuit d’évacuationExemple de circuit d’évacuation Longueur maximum = 60 pi 18,3 mPréparation du plan de travail Cuisinières encastrées uniquementInstructions D’INSTALLATION Déballage de la cuisinièreRéglage des pieds de nivellement Déterminer la longueur équivalente du circuit d’évacuation Installation de la bride antibasculementInstallation du circuit d’évacuation par le Bas Montage au plancher Montage muralÉvacuation par le mur arrière Vue de dessusVue de dessus Vue du ventilateur coté moteur Placer 2 cales en bois et les fixer au sol Évacuation par le mur Vue de dessus Évacuation par le plancher Vue de dessusAchever l’installation Évacuation latérale évacuation par la gauche illustréeSi la cuisinière ne fonctionne pas, contrôler ce qui suit Cuisinières alimentées par cordon d’alimentation Déplacement de la cuisinièreSi vous avez besoin d’assistance ou de service Pour les cuisinières avec câblage directW10430955A 2011 12/11 All rights reserved

W10430955A specifications

The Jenn-Air W10430955A is a premium kitchen appliance designed to elevate culinary experiences and integrate seamlessly into modern kitchens. As a vital component of Jenn-Air's commitment to innovation and performance, the W10430955A represents a fusion of advanced technology and stylish design.

One of the standout features of the W10430955A is its precision cooking technology. This appliance is engineered to provide consistent, even cooking results, thanks to its advanced temperature management system. This system allows home cooks to achieve professional-grade results, whether they are baking, roasting, or broiling.

Moreover, the W10430955A incorporates a sleek, intuitive control panel that simplifies operation. With its user-friendly interface, cooks can easily select settings, adjust temperatures, and monitor cooking times with precision. The touch-sensitive controls not only enhance functionality but also contribute to the overall aesthetic of the appliance, offering a modern touch to any kitchen decor.

In terms of design, the W10430955A features a contemporary look with high-quality materials, including stainless steel finishes that are both durable and easy to clean. The appliance is also designed for energy efficiency, which not only reduces utility bills but also makes it an environmentally friendly choice for those striving to minimize their carbon footprint.

Another commendable characteristic of the W10430955A is its flexibility in cooking options. It often includes multiple cooking modes that cater to various culinary techniques, providing versatility for a wide range of dishes. Whether preparing a delicate soufflé or a hearty casserole, this appliance stands out for its adaptability.

Furthermore, maintenance is hassle-free with this model. Many components are designed for easy removal and cleaning, ensuring that users can keep their appliance in optimal condition with minimal effort.

Overall, the Jenn-Air W10430955A is an exceptional combination of performance, style, and convenience. Its innovative technologies and user-friendly features make it an ideal choice for both amateur cooks and seasoned chefs looking to enhance their culinary skills in a modern kitchen setting. Investing in this appliance not only elevates cooking experiences but also adds a touch of elegance to any home.
Top Page Image Contents