Jenn-Air W10430955A installation instructions Wire Connection Direct Wire

Page 17

3-wire connection: Power Supply Cord

 

Direct Wire Installation: Copper or Aluminum Wire

Use this method only if local codes permit connecting chassis ground conductor to neutral wire of power supply cord.

1.Feed the power supply cord through the opening in the cord/ conduit plate on bottom of range. Allow enough slack to easily attach the wiring to the terminal block.

A

B

C

D

A. Terminal block

C. Cord/conduit plate

B. Ground-link screw

D. Power supply cord wires

2.Use ³⁄₈" nut driver to connect the neutral (white) wire to the center terminal block post with one of the 10–32 hex nuts.

A

E

 

B

D

 

 

C

A. 10–32 hex nut

D. Neutral (white) wire

B. Line 1 (black)

E. Line 2 (red)

C.Ground-link screw

3.Connect line 1 (black) and line 2 (red) wires to the outer terminal block posts with 10-32 hex nuts.

4.Securely tighten hex nuts.

NOTE: For power supply cord replacement, only use a power cord rated at 250 volts minimum, 40 amps or 50 amps that is marked for use with nominal 1³⁄₈" (3.5 cm) diameter connection opening, with ring terminals and marked for use with ranges.

5.Replace terminal block access cover.

This range may be connected directly to the fuse disconnect or circuit breaker box. Depending on your electrical supply, make the required 3-wire or 4-wire connection.

1.Strip outer covering back 3" (7.6 cm) to expose wires. Strip the insulation back 1" (2.5 cm) from the end of each wire.

1"

(2.5 cm)

3"

(7.6 cm)

2.Allow enough slack in the wire to easily attach the wiring terminal block.

3.Complete electrical connection according to your type of electrical supply (4-wire or 3-wire connection).

4-wire Connection: Direct Wire

Use this method for:

New branch-circuit installations (1996 NEC)

Mobile homes

Recreational vehicles

In an area where local codes prohibit grounding through the neutral

1.Part of metal ground strap must be cut out and removed.

A

B

C

A. Metal ground strap

B.Discard

C.Ground-link screw

2.Use Phillips screwdriver to remove the ground-link screw from the back of the range. Save the ground-link screw and the end of the ground-link under the screw.

17

Image 17
Contents Table of Contents/Table des matières Your safety and the safety of others are very important Range SafetyLocation Requirements Installation RequirementsTools and Parts Product Dimensions Cabinet Dimensions Venting Methods Venting RequirementsWall Venting Floor VentingConcrete Slab Installations Exhaust Through Window Well Concrete Slab Installations Exhaust Through WallCalculating Vent System Length Left or Right Side VentingElectrical Requirements U.S.A. Only If connecting to a 4-wire systemExample vent system Electrical ConnectionCountertop Preparation If connecting to a 3-wire systemElectrical Requirements Canada Only Adjust Leveling Legs Installation InstructionsInstall Anti-Tip Bracket Unpack RangeRear Wall Venting Install Downdraft SystemDetermine Equivalent Length of Vent System Floor Mounting Wall MountingTop View Top View View from Motor Side of Blower Electrical Connection U.S.A. Only Power Supply Cord Direct WireStyle 1 Power supply cord strain relief Removable retaining nut Strain relief Style 2 Direct wire strain reliefWire connection Power Supply Cord Wire Connection Direct Wire Wire Awg Torque Bare Wire Torque SpecificationsGauge copper Lbs-in .8 N-m Gauge aluminum Lbs-in .0 N-m Connect Range to Downdraft System Floor Venting Top View Verify Anti-Tip Is Installed and EngagedWall Venting Top View Side Venting left side venting shown If you need Assistance or Service Complete InstallationFor power supply cord-connected ranges Moving the RangeFor direct-wired ranges Votre sécurité et celle des autres est très importante Sécurité DE LA CuisinièreOutils et pièces Exigences D’INSTALLATIONExigences d’emplacement Dimensions du produit Dimensions du placardExigences concernant l’évacuation Installations dans les régions au climat froidPour obtenir des performances optimales Air d’appointMéthodes d’évacuation Installations sur dalle de béton Évacuation par le murÉvacuation par le mur Évacuation par le plancherExemple de circuit d’évacuation Calcul de la longueur effective du circuit d’évacuationComposant Conduit de diamètre de 15,2 cm Coude à Longueur maximum = 60 pi 18,3 mCuisinières encastrées uniquement Préparation du plan de travailRéglage des pieds de nivellement Instructions D’INSTALLATIONDéballage de la cuisinière Installation du circuit d’évacuation par le Bas Installation de la bride antibasculementDéterminer la longueur équivalente du circuit d’évacuation Montage au plancher Montage muralVue de dessus Évacuation par le mur arrièreVue de dessus Vue du ventilateur coté moteur Placer 2 cales en bois et les fixer au sol Évacuation par le plancher Vue de dessus Évacuation par le mur Vue de dessusSi la cuisinière ne fonctionne pas, contrôler ce qui suit Achever l’installationÉvacuation latérale évacuation par la gauche illustrée Si vous avez besoin d’assistance ou de service Déplacement de la cuisinièreCuisinières alimentées par cordon d’alimentation Pour les cuisinières avec câblage direct2011 12/11 All rights reserved W10430955A

W10430955A specifications

The Jenn-Air W10430955A is a premium kitchen appliance designed to elevate culinary experiences and integrate seamlessly into modern kitchens. As a vital component of Jenn-Air's commitment to innovation and performance, the W10430955A represents a fusion of advanced technology and stylish design.

One of the standout features of the W10430955A is its precision cooking technology. This appliance is engineered to provide consistent, even cooking results, thanks to its advanced temperature management system. This system allows home cooks to achieve professional-grade results, whether they are baking, roasting, or broiling.

Moreover, the W10430955A incorporates a sleek, intuitive control panel that simplifies operation. With its user-friendly interface, cooks can easily select settings, adjust temperatures, and monitor cooking times with precision. The touch-sensitive controls not only enhance functionality but also contribute to the overall aesthetic of the appliance, offering a modern touch to any kitchen decor.

In terms of design, the W10430955A features a contemporary look with high-quality materials, including stainless steel finishes that are both durable and easy to clean. The appliance is also designed for energy efficiency, which not only reduces utility bills but also makes it an environmentally friendly choice for those striving to minimize their carbon footprint.

Another commendable characteristic of the W10430955A is its flexibility in cooking options. It often includes multiple cooking modes that cater to various culinary techniques, providing versatility for a wide range of dishes. Whether preparing a delicate soufflé or a hearty casserole, this appliance stands out for its adaptability.

Furthermore, maintenance is hassle-free with this model. Many components are designed for easy removal and cleaning, ensuring that users can keep their appliance in optimal condition with minimal effort.

Overall, the Jenn-Air W10430955A is an exceptional combination of performance, style, and convenience. Its innovative technologies and user-friendly features make it an ideal choice for both amateur cooks and seasoned chefs looking to enhance their culinary skills in a modern kitchen setting. Investing in this appliance not only elevates cooking experiences but also adds a touch of elegance to any home.