Jenn-Air W10430955A Venting Requirements, Venting Methods, Wall Venting, Floor Venting

Page 5

Venting Requirements

IMPORTANT: This range must be exhausted outdoors. See “Venting Methods” section.

■Do not terminate the vent system in an attic or other enclosed area.

■Use a Jenn-Air wall cap.

■Vent system must terminate to the outside.

■Use only a 6" (15.2 cm) round metal vent or a 3¼ x 10"

(8.3 cm x 25.4 cm) rectangular vent, except as follows:

5" (12.7 cm) round metal vent may be used for venting straight out the back of the range and directly through the wall for vent lengths of 10 ft (3.0 m) or less.

■Rigid metal vent is recommended. For best performance, do not use plastic or metal foil vent.

■Before making cutouts, make sure there is proper clearance within the wall or floor for the exhaust vent.

■Do not cut a joist or stud unless absolutely necessary. If a joist or stud must be cut, then a supporting frame must be constructed.

■The size of the vent should be uniform.

■The vent system must have a damper. If roof or wall cap has a damper, do not use damper supplied with the range hood.

■Use vent clamps to seal all joints in the vent system.

■Use caulking to seal exterior wall or roof opening around the cap.

■Determine which venting method is best for your application.

For Best Performance:

■Use 26-gauge minimum galvanized or 25-gauge minimum aluminum metal vent. Poor quality pipe fittings can reduce airflow. Flexible metal vent is not recommended.

NOTE: Local codes may require a heavier gauge material.

■Metal duct may be reduced to 30-gauge galvanized steel or 26-gauge aluminized steel if allowed by local codes. This reduction is based on information in the International Residential Codes Section M1601.1 (2006 edition).

■Do not install 2 elbows together.

■Use no more than three 90° elbows.

■If an elbow is used, install it as far away as possible from the hood’s vent motor exhaust opening.

■Make sure there is a minimum of 18" (45.7 cm) of straight vent between the elbows if more than one elbow is used.

■Elbows too close together can cause excess turbulence that reduces airflow.

■Do not use a 5" (12.7 cm) elbow in a 6" (15.2 cm) or 3¹⁄₄" x 10" (8.3 x 25.4 cm) system.

■Do not reduce to a 5" (12.7 cm) system after using a 6" (15.2 cm) or 3¹⁄₄" x 10" (8.3 x 25.4 cm) fittings.

■Avoid forming handmade crimps. Handmade crimps may restrict airflow.

■Use a Jenn-Air vent cap for proper performance. If an alternate wall or roof cap is used, be certain the cap size is not reduced and that it has a backdraft damper.

■Use vent clamps to seal all joints in the vent system.

■Use caulking to seal exterior wall or roof opening around the cap.

The length of vent system and number of elbows should be kept to a minimum to provide efficient performance.

The maximum equivalent length of the vent system is

60 ft (18.3 m). For altitudes above 4,500 ft (1272 m), reduce recommended vent run by 20% for best performance.

Cold Weather Installations

An additional backdraft damper should be installed to minimize backward cold air flow and a thermal break installed to minimize conduction of outside temperatures as part of the vent system.

The damper should be on the cold air side of the thermal break.

Makeup Air

Local building codes may require the use of makeup air systems when using ventilation systems greater than specified CFM of air movement. The specified CFM varies from locale to locale.

Consult your HVAC professional for specific requirements in your area.

Venting Methods

Common venting methods are shown for a downdraft range. The downdraft range may be vented through the wall or floor.

Wall Venting

A

B

A. Wall cap

B. 6" (15.2 cm) round roof venting

Floor Venting

Venting Between Floor Joists

A

B

A. Wall cap

B. 6" (15.2 cm) round roof venting

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Table of Contents/Table des matières Your safety and the safety of others are very important Range SafetyLocation Requirements Installation RequirementsTools and Parts Product Dimensions Cabinet Dimensions Venting Methods Venting RequirementsWall Venting Floor VentingConcrete Slab Installations Exhaust Through Window Well Concrete Slab Installations Exhaust Through WallCalculating Vent System Length Left or Right Side VentingElectrical Requirements U.S.A. Only If connecting to a 4-wire systemExample vent system Electrical ConnectionCountertop Preparation If connecting to a 3-wire systemElectrical Requirements Canada Only Adjust Leveling Legs Installation InstructionsInstall Anti-Tip Bracket Unpack RangeRear Wall Venting Install Downdraft SystemDetermine Equivalent Length of Vent System Floor Mounting Wall MountingTop View Top View View from Motor Side of Blower Electrical Connection U.S.A. Only Power Supply Cord Direct WireStyle 1 Power supply cord strain relief Removable retaining nut Strain relief Style 2 Direct wire strain reliefWire connection Power Supply Cord Wire Connection Direct Wire Wire Awg Torque Bare Wire Torque SpecificationsGauge copper Lbs-in .8 N-m Gauge aluminum Lbs-in .0 N-m Connect Range to Downdraft System Floor Venting Top View Verify Anti-Tip Is Installed and EngagedWall Venting Top View Side Venting left side venting shown If you need Assistance or Service Complete InstallationFor power supply cord-connected ranges Moving the RangeFor direct-wired ranges Votre sécurité et celle des autres est très importante Sécurité DE LA CuisinièreOutils et pièces Exigences D’INSTALLATIONExigences d’emplacement Dimensions du produit Dimensions du placardExigences concernant l’évacuation Installations dans les régions au climat froidPour obtenir des performances optimales Air d’appointMéthodes d’évacuation Installations sur dalle de béton Évacuation par le murÉvacuation par le mur Évacuation par le plancherExemple de circuit d’évacuation Calcul de la longueur effective du circuit d’évacuationComposant Conduit de diamètre de 15,2 cm Coude à Longueur maximum = 60 pi 18,3 mCuisinières encastrées uniquement Préparation du plan de travailRéglage des pieds de nivellement Instructions D’INSTALLATIONDéballage de la cuisinière Installation du circuit d’évacuation par le Bas Installation de la bride antibasculementDéterminer la longueur équivalente du circuit d’évacuation Montage au plancher Montage muralVue de dessus Évacuation par le mur arrièreVue de dessus Vue du ventilateur coté moteur Placer 2 cales en bois et les fixer au sol Évacuation par le plancher Vue de dessus Évacuation par le mur Vue de dessusSi la cuisinière ne fonctionne pas, contrôler ce qui suit Achever l’installationÉvacuation latérale évacuation par la gauche illustrée Si vous avez besoin d’assistance ou de service Déplacement de la cuisinièreCuisinières alimentées par cordon d’alimentation Pour les cuisinières avec câblage direct2011 12/11 All rights reserved W10430955A

W10430955A specifications

The Jenn-Air W10430955A is a premium kitchen appliance designed to elevate culinary experiences and integrate seamlessly into modern kitchens. As a vital component of Jenn-Air's commitment to innovation and performance, the W10430955A represents a fusion of advanced technology and stylish design.

One of the standout features of the W10430955A is its precision cooking technology. This appliance is engineered to provide consistent, even cooking results, thanks to its advanced temperature management system. This system allows home cooks to achieve professional-grade results, whether they are baking, roasting, or broiling.

Moreover, the W10430955A incorporates a sleek, intuitive control panel that simplifies operation. With its user-friendly interface, cooks can easily select settings, adjust temperatures, and monitor cooking times with precision. The touch-sensitive controls not only enhance functionality but also contribute to the overall aesthetic of the appliance, offering a modern touch to any kitchen decor.

In terms of design, the W10430955A features a contemporary look with high-quality materials, including stainless steel finishes that are both durable and easy to clean. The appliance is also designed for energy efficiency, which not only reduces utility bills but also makes it an environmentally friendly choice for those striving to minimize their carbon footprint.

Another commendable characteristic of the W10430955A is its flexibility in cooking options. It often includes multiple cooking modes that cater to various culinary techniques, providing versatility for a wide range of dishes. Whether preparing a delicate soufflé or a hearty casserole, this appliance stands out for its adaptability.

Furthermore, maintenance is hassle-free with this model. Many components are designed for easy removal and cleaning, ensuring that users can keep their appliance in optimal condition with minimal effort.

Overall, the Jenn-Air W10430955A is an exceptional combination of performance, style, and convenience. Its innovative technologies and user-friendly features make it an ideal choice for both amateur cooks and seasoned chefs looking to enhance their culinary skills in a modern kitchen setting. Investing in this appliance not only elevates cooking experiences but also adds a touch of elegance to any home.
Top Page Image Contents