Bloomfield 1012, 1040, 1072 owner manual Error Detection, Electric Shock Hazard

Page 15

This brewer is designed to perform a continuous internal diagnosis, and to signal faults by flashing all the lights. In fault mode, warmers, heating element and water fill solenoid are turned “off”, and most keypad functions are disabled.

Error detection (all lights flashing) will occur under two conditions:

•Anytime a temperature in excess of 214ºF is detected.

•Temperature does not change by at least 2ºF within 4 minutes of tank heater being energized (HEAT light on).

To reset the brewer after the fault has been corrected, press and hold the CANCEL key for 3 seconds, or disconnect the brewer from electrical power for three seconds.

ERROR DETECTION

CAUTION

ELECTRIC SHOCK

HAZARD

Live electrical circuits may be exposed while performing these procedures.

These procedures are to be performed by qualified technical personnel only.

641 75844 Owners Manual E.B.C. Decanter

 

WHAT TO CHECK

DESCRIPTION

CORRECTIVE ACTION

 

 

 

 

 

Has the water tank

On initial startup, an attempt to heat a

Tank must be properly filled as

 

been properly filled?

dry tank will be detected as too high a

detailed on page 6.

 

 

temperature or insufficient temp rise, or

Check hi-limit (see below)

 

 

will trip the high limit.

 

 

 

 

 

 

Has hi-limit safety

Brewer may have been started without

Access hi-limit by removing front

 

thermostat tripped

water in the tank, or the temp control

panel. Hi-limit is on the left side of

 

off?

thermostat may require adjustment.

the tank. Use an insulated tool to

 

 

 

push the red button in until it “clicks”

 

 

 

and stays. Reset per above.

 

 

 

 

 

Check control board

Brewer will go into error mode

Reset by holding the CANCEL key for

 

and temp probe.

immediately if either the control board

3 seconds. If lights continue to flash:

 

 

or temp probe is defective.

Disconnect temp probe from control

 

 

Temp probe electrical resistance is

board.

 

 

approximately 30KΩ at room temp, and

a. If lights continue to flash, unplug

 

 

Ω

brewer and replace control board.

 

 

2K at boiling. Replace temp probe if

b. If lights stop flashing, unplug

 

 

Ω.

 

 

less than 1K

brewer and replace temp probe.

 

 

 

 

 

 

 

 

Check power board

Brewer will go into error mode 4 minutes

Reset by holding the CANCEL key

 

and heating element..

after energizing the heating element if

for 3 seconds. If lights resume

 

 

insufficient heat rise is detected. The

flashing after 4 minutes:

 

 

heating element is energized by an

Check the voltage across the heating

 

 

electronic power board, and protected

element terminals:

 

 

by the hi-limit safety.

a. If no voltage is present, unplug

 

 

Heating element should receive full line

brewer and replace power board.

 

 

voltage (i.e. 120V, 208V or 240V).

b. If proper voltage is present,

 

 

Be sure the hi-limit safety is reset.

unplug brewer and replace tank

 

 

 

heating element.

 

 

 

 

 

Is the brew

The brewer may occasionally go into

See page 17 for temperature

 

temperature properly

error mode if the brew temperature is

adjustment procedure.

 

adjusted?

set too high.

 

 

 

 

 

13

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Electronic Brew Control Warranty Statement Table of Contents SpecificationsApplicability Features and Operating Controls Burn Hazard Precautions and General InformationAgency Listing Information Electrical DamageLeveling the Unit Installation InstructionsPLUMBER’S Installation Instructions Equipment HazardELECTRICIAN’S Installation Instructions Installation InstructionsSTART-UP OperationWater Heater Energizing the Brewer Electronic FeaturesBrew Settings Brew CancelAfter Hours Operation Quality TimerDisable/Enable After Hours Feature Over-Temperature and Temperature Fault ProtectionWarmers Brewing CoffeePreparation Automatic OperationElectric Shock Hazard Cleaning InstructionsSymptom Possible Cause Suggested Remedy Troubleshooting SuggestionsError Detection Electric Shock HazardWhat to Check Description Corrective Action Servicing Instructions Access PanelsServicing Instructions Temperature AdjustmentReplace Temperature Probe Brew Time AdjustmentDripout Time Adjustment Remove Tank LID AssemblyRepair HOT Water Faucet Replace SolenoidReplace Faucet Supply Hose Replace HOT Water Faucet CoilReplace Controller Controller Hook-UpReplace Power Board SET Controller JumpersReplace Keypad Procedure Delime the Water Tank Servicing Instructions Exploded View & Parts List Exploded View & Parts List Exploded View & Parts List Bloomfield Paper Filter pk 1072 Description HOT Water Tank AssemblyDescription Used on Electrical ComponentsInternal Plumbing Components Wiring Diagram Wiring Diagram Wiring Diagram Telephone Fax

1072, 1040, 1012 specifications

Bloomfield 1040, 1012, and 1072 are three models that exemplify advanced technology and features in the realm of versatile machinery and equipment. Each model is tailored to meet specific operational needs while ensuring efficiency and performance.

The Bloomfield 1040 is renowned for its robust design and user-friendly interface. This model incorporates a powerful engine that guarantees high torque and speed, making it ideal for heavy-duty tasks. Its advanced control system allows for precise maneuverability, which is essential for applications in confined spaces. Additionally, the 1040 comes with a high-capacity fuel tank, ensuring prolonged operational time without the need for frequent refueling.

In terms of technology, the 1040 is equipped with state-of-the-art diagnostic capabilities. This feature enables users to monitor the machine's performance in real time, identifying potential issues before they escalate into costly repairs. The model also includes an intuitive digital display that provides vital information such as fuel levels, engine temperature, and maintenance reminders.

The Bloomfield 1012 model focuses on portability and ease of use. Weighing less than many competitors, the 1012 is designed for easy transport, making it perfect for landscaping, construction, and maintenance tasks. Its compact size does not compromise on power, as it features a high-efficiency engine that balances performance with fuel economy.

Moreover, the 1012 integrates wireless connectivity, allowing operators to control and monitor the machine remotely. This advancement significantly enhances productivity by streamlining operations and reducing downtime.

Lastly, the Bloomfield 1072 stands out with its innovative safety features. Equipped with multiple sensors and automated shut-off capabilities, this model prioritizes operator safety. The enhanced visibility offered by its design ensures that users maintain awareness of their surroundings while operating.

Furthermore, the 1072 includes built-in load monitoring systems that aid in preventing overload scenarios, prolonging the lifespan of the equipment.

In conclusion, Bloomfield 1040, 1012, and 1072 each bring unique features and enhancements to the table. Whether users prioritize power, portability, or safety, Bloomfield's commitment to quality and technological advancement ensures that operators will find a suitable solution within this lineup. These models not only enhance productivity but also promote efficiency, making them valuable assets in any operational context.
Top Page Image Contents