Manuals / Miller Electric / Power Tools / Welder

Miller Electric PipePro Dual Setting Internal DIP Switches, Automatic Run-In OFF S1-1 And S1-2

Models: PipePro Dual

1 48

Download 48 pages 56.03 Kb

Page 23

5-7. Setting Internal DIP Switches

Right Side Motor

Control Board PC1

P1

Left Side Motor

Control Board

PC101

Remove wrapper.

1DIP Switch S1 On Motor Board PC1

wSetting Current Detect Override (S1-1)

Current detect override is used to disable run-in when a welding pow- er source is used that doesn’t pro- vide current feedback through the 14-pin receptacle.

Install wrapper when finished.

	. This illustration shows				1
	the factory setting of S1.				1
	the factory setting of S1.

. In the DIP switch S1 illustrations, the elevated slider on each switch is shown in white. For example, the switches above are all in the Off position.

.When DIP switch positions are changed, the unit must be

turned Off and then On again in order for the new settings to be active. DIP switches are only read on power up.

Tools Needed:

1/4 in

Position Settings And Results For DIP Switch S1 On PC1 And PC101

Automatic Run-In (ON)

(Factory Default)

S1-1 And S1-2

On = Run-In speed is approximately 1/2 weld wire feed speed.

Automatic Run-In (OFF)

S1-1 And S1-2

Off = Run-In speed is set using potentiometer P1 located on Motor Board PC1.

Current Detect Override (ON)

S1-1 And S1-2

On = Current detect over- ride. For welding power sources that don’t provide current feedback through the 14-pin receptacle. Run- in is inactive.

Current Detect Override (OFF)

(Factory Default)

S1-1 And S1-2

Off = Current must be detected from power sources that provide current feedback through the

14-pin receptacle to go from run-in to welding condition. Run-in is active.

804 804-A / Ref. 802 944

OM-230 009 Page 19

Image 23

Miller Electric PipePro Dual manual Setting Internal DIP Switches, Right Side Motor Control Board PC1 Left Side Motor PC101

Contents

File MIG Gmaw OM-230 009FProcesses DescriptionFrom Miller to You Table of Contents Page HOT Parts can cause severe burns Symbol UsageArc Welding Hazards Electric Shock can killFlying Metal or Dirt can injure eyes Fumes and Gases can be hazardousARC Rays can burn eyes and skin Welding can cause fire or explosionMoving Parts can cause injury Welding Wire can cause injuryFire or Explosion hazard Falling Unit can cause injuryAbout Implanted Medical Devices Principal Safety StandardsCalifornia Proposition 65 Warnings EMF InformationUNE Décharge Électrique peut entraîner la mort Symboles utilisésLE Soudage peut provoquer un in cendie ou une explosion DES Pièces Chaudes peuvent provoquer des brûlures gravesLES Fumées ET LES GAZ peuvent être dangereux LA Chute DE L’APPAREIL peut blesser LE Bruit peut endommager l’ouïeLES Bouteilles peuvent exploser si elles sont endommagées Risque D’INCENDIE OU D’EXPLO- SionLE Soudage À L’ARC risque de provoquer des interférences Proposition californienne 65 AvertissementsLES Fils DE Soudage peuvent provoquer des blessures En ce qui concerne les implants médicaux Principales normes de sécuritéInformation EMF OM-230 009 Keep your head out of the fumes Disconnect input plug or power before working on machine− Definitions Drive rolls can injure fingersRating Symbols And DefinitionsSpecifications − IntroductionTypical Connection Diagram For MIG Equipment − InstallationTypical Connection Diagram For TIG Equipment Typical Connection Diagram For Stick Equipment Rear Panel Connections And Rotating Drive Assembly Pin Pin Information Pin Plug InformationInstalling And Threading Welding Wire Automatic Run-In OFF S1-1 And S1-2 Setting Internal DIP SwitchesCurrent Detect Override OFF Factory Default S1-1 And S1-2 Right Side Motor Control Board PC1 Left Side Motor PC101Tools Needed Remove wrapper DIP Switch S1 And S4 Display Board DIP Switch SettingsFactory Set Default Settings For DIP Switches S1 And S4 Operational Terms Power SwitchLeft/Right Select Switch − OperationTime sec Jog/Purge SwitchFront Panel Controls SeeUpper Display Push Button Program Push ButtonUpper Display Upper DisplayLower Display Setup Push ButtonWeld Adjust ControlWelding Sequence Diagram Sequence Push ButtonAuxiliary Menus Software Revision Level Wire Feed Speed UnitsWhen the Setup button is pressed again, the menu repeats Range LocksAt the same time, as both Remote-14 Receptacle InformationSequence Parameters In a Program − Setting Sequence Parameters− Setting Dual Schedule Parameters Optional Dual Schedule Switch DiagramsLED3-Related Error Indications DiagnosticsIndicates a com Indicates a trigger Munication error Error = Check ~ = Clean = Replace Reference Every − Maintenance & TroubleshootingRoutine Maintenance Disconnect power before maintainingTrouble Remedy TroubleshootingDisconnect power before troubleshooting Material Thickness Gauge Circuit Diagram − Electrical Diagram229 867-A 21 −2 − Parts ListPart Description Quantity Control Box GS1,101 219 Drive Assembly, Wire -1Item Drive Assembly, Wire203 Roll Drive Kit Drive Roll And Wire Guide Kits Fraction MetricKit Roll Wire Size Roll DriveSupport ServiceYour distributor also gives Your distributor and/or equipment manufacturer’s To locate a Distributor or Service Agency visitMiller Electric Mfg. Co For assistance in filing or settling claims, contact