Pin Plug Information | Miller Electric PipePro Dual instruction

5-5. 14-Pin Plug Information

			Pin*	Pin Information
			A	40 volts dc with respect to socket G.
			G	Circuit common for 40 volts dc circuit.
			B	Contact closure to K completes contactor control circuit.
			K	Contact closure to B completes contactor control circuit.
J	K	A	C	+10 volts dc input from power source to wire feeder with respect to socket D.
I	K	B
		B	D	Remote volt control circuit common.
H	N	L C	D	Remote volt control circuit common.
H	N	L C	E	0 to +10 volts dc remote volt/trim signal from wire feeder to power source with respect to socket D.
G	M	D	E
F	E		H	Voltage feedback; 0 to +10 volts dc, 1 volt per 10 arc volts.
			H
			F	Current feedback; 0 to +10 volts dc, 1 volt per 100 amperes.
			M	0 to +10 volts dc remote WFS signal from wire feeder to power source with respect to socket N.
			N	Remote WFS control circuit common.
			L	Electrode sense.
			I	Remote Program Select A
			J	Remote Program Select B

Notes

OM-230 009 Page 17

Page 21

Image 21

Miller Electric PipePro Dual manual Pin Plug Information, Pin Pin Information

Contents

Processes OM-230 009FDescription File MIG Gmaw From Miller to You Table of Contents Page Arc Welding Hazards Symbol UsageElectric Shock can kill HOT Parts can cause severe burns ARC Rays can burn eyes and skin Fumes and Gases can be hazardousWelding can cause fire or explosion Flying Metal or Dirt can injure eyes Fire or Explosion hazard Welding Wire can cause injuryFalling Unit can cause injury Moving Parts can cause injury California Proposition 65 Warnings Principal Safety StandardsEMF Information About Implanted Medical Devices UNE Décharge Électrique peut entraîner la mort Symboles utilisés DES Pièces Chaudes peuvent provoquer des brûlures graves LES Fumées ET LES GAZ peuvent être dangereuxLE Soudage peut provoquer un in cendie ou une explosion LES Bouteilles peuvent exploser si elles sont endommagées LE Bruit peut endommager l’ouïeRisque D’INCENDIE OU D’EXPLO- Sion LA Chute DE L’APPAREIL peut blesser Proposition californienne 65 Avertissements LES Fils DE Soudage peuvent provoquer des blessuresLE Soudage À L’ARC risque de provoquer des interférences Principales normes de sécurité Information EMFEn ce qui concerne les implants médicaux OM-230 009 − Definitions Disconnect input plug or power before working on machineDrive rolls can injure fingers Keep your head out of the fumes Specifications Symbols And Definitions− Introduction Rating Typical Connection Diagram For MIG Equipment − Installation Typical Connection Diagram For TIG Equipment Typical Connection Diagram For Stick Equipment Rear Panel Connections And Rotating Drive Assembly Pin Pin Information Pin Plug Information Installing And Threading Welding Wire Current Detect Override OFF Factory Default S1-1 And S1-2 Setting Internal DIP SwitchesRight Side Motor Control Board PC1 Left Side Motor PC101 Automatic Run-In OFF S1-1 And S1-2 Display Board DIP Switch Settings Factory Set Default Settings For DIP Switches S1 And S4Tools Needed Remove wrapper DIP Switch S1 And S4 Left/Right Select Switch Power Switch− Operation Operational Terms Front Panel Controls Jog/Purge SwitchSee Time sec Upper Display Program Push ButtonUpper Display Upper Display Push Button Lower Display Setup Push Button Welding Sequence Diagram Adjust ControlSequence Push Button Weld Auxiliary Menus When the Setup button is pressed again, the menu repeats Wire Feed Speed UnitsRange Locks Software Revision Level At the same time, as both Remote-14 Receptacle Information − Setting Dual Schedule Parameters − Setting Sequence ParametersOptional Dual Schedule Switch Diagrams Sequence Parameters In a Program Diagnostics Indicates a com Indicates a trigger Munication error ErrorLED3-Related Error Indications Routine Maintenance − Maintenance & TroubleshootingDisconnect power before maintaining = Check ~ = Clean = Replace Reference Every Troubleshooting Disconnect power before troubleshootingTrouble Remedy Material Thickness Gauge Circuit Diagram − Electrical Diagram 229 867-A 21 −2 − Parts List Part Description Quantity Control Box GS1,101 219 Drive Assembly, Wire -1Item Drive Assembly, Wire 203 Kit Roll Wire Size Drive Roll And Wire Guide Kits Fraction MetricRoll Drive Roll Drive Kit Service Your distributor also givesSupport Miller Electric Mfg. Co To locate a Distributor or Service Agency visitFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s

5-5. 14-Pin Plug Information

Pin*

Pin Information

Remote volt control circuit common.

Current feedback; 0 to +10 volts dc, 1 volt per 100 amperes.

OM-230 009 Page 17