Manuals / Miller Electric / Power Tools / Welder

Miller Electric PipePro Dual manual Jog/Purge Switch, Front Panel Controls, See, Time sec

Models: PipePro Dual

1 48

Download 48 pages 56.03 Kb

Page 26

Image 26

6-4. Jog/Purge Switch

1 Jog/Purge Switch

2 Gun Trigger Receptacle

3 Adjust Control

Pressing the Jog/Purge switch allows the operator to jog wire without energizing the weld pow- er or gas valve circuit.

• Jog speed can be adjusted by the Adjust control when the unit is jogging wire. The unit displays jog speed when the unit is being jogged.

		• Pressing the Jog/Purge button
		also allows the operator to
	3	purge gas lines before welding
	3	and to preset gas pressure at
		and to preset gas pressure at
		the regulator.

	2
	1
					804 668-B
6-5. Front Panel Controls
					See
					Section
					6-7
See
Section	Program	V/Trim	Time (sec)		See
6-6	Program	V/Trim	Time (sec)		See
6-6					Section
					Section
					6-8
		Wire Speed		Amps
	Start
	Crater				Dual Schedule
	Pre/Postflow				Trigger Hold
					Trigger Hold
	Sequence			Adjust	Setup
	See	See			See
	Section	Section			Section
	6-11	6-10			6-9
OM-230 009 Page 22

Page 26

Image 26

Miller Electric PipePro Dual manual Jog/Purge Switch, Front Panel Controls, See, Time sec, Section OM-230 009

Contents

Description OM-230 009FProcesses File MIG GmawFrom Miller to You Table of Contents Page Electric Shock can kill Symbol UsageArc Welding Hazards HOT Parts can cause severe burnsWelding can cause fire or explosion Fumes and Gases can be hazardousARC Rays can burn eyes and skin Flying Metal or Dirt can injure eyesFalling Unit can cause injury Welding Wire can cause injuryFire or Explosion hazard Moving Parts can cause injuryEMF Information Principal Safety StandardsCalifornia Proposition 65 Warnings About Implanted Medical DevicesSymboles utilisés UNE Décharge Électrique peut entraîner la mortLE Soudage peut provoquer un in cendie ou une explosion DES Pièces Chaudes peuvent provoquer des brûlures gravesLES Fumées ET LES GAZ peuvent être dangereux Risque D’INCENDIE OU D’EXPLO- Sion LE Bruit peut endommager l’ouïeLES Bouteilles peuvent exploser si elles sont endommagées LA Chute DE L’APPAREIL peut blesserLE Soudage À L’ARC risque de provoquer des interférences Proposition californienne 65 AvertissementsLES Fils DE Soudage peuvent provoquer des blessures En ce qui concerne les implants médicaux Principales normes de sécuritéInformation EMF OM-230 009 Drive rolls can injure fingers Disconnect input plug or power before working on machine− Definitions Keep your head out of the fumes− Introduction Symbols And DefinitionsSpecifications Rating− Installation Typical Connection Diagram For MIG EquipmentTypical Connection Diagram For TIG Equipment Typical Connection Diagram For Stick Equipment Rear Panel Connections And Rotating Drive Assembly Pin Plug Information Pin Pin InformationInstalling And Threading Welding Wire Right Side Motor Control Board PC1 Left Side Motor PC101 Setting Internal DIP SwitchesCurrent Detect Override OFF Factory Default S1-1 And S1-2 Automatic Run-In OFF S1-1 And S1-2Tools Needed Remove wrapper DIP Switch S1 And S4 Display Board DIP Switch SettingsFactory Set Default Settings For DIP Switches S1 And S4 − Operation Power SwitchLeft/Right Select Switch Operational TermsSee Jog/Purge SwitchFront Panel Controls Time secUpper Display Program Push ButtonUpper Display Upper Display Push ButtonSetup Push Button Lower DisplaySequence Push Button Adjust ControlWelding Sequence Diagram WeldAuxiliary Menus Range Locks Wire Feed Speed UnitsWhen the Setup button is pressed again, the menu repeats Software Revision LevelRemote-14 Receptacle Information At the same time, as bothOptional Dual Schedule Switch Diagrams − Setting Sequence Parameters− Setting Dual Schedule Parameters Sequence Parameters In a ProgramLED3-Related Error Indications DiagnosticsIndicates a com Indicates a trigger Munication error Error Disconnect power before maintaining − Maintenance & TroubleshootingRoutine Maintenance = Check ~ = Clean = Replace Reference EveryTrouble Remedy TroubleshootingDisconnect power before troubleshooting Material Thickness Gauge − Electrical Diagram Circuit Diagram229 867-A − Parts List 21 −2Part Description Quantity Control Box GS1,101 219 Drive Assembly, Wire Drive Assembly, Wire -1Item203 Roll Drive Drive Roll And Wire Guide Kits Fraction MetricKit Roll Wire Size Roll Drive KitSupport ServiceYour distributor also gives For assistance in filing or settling claims, contact To locate a Distributor or Service Agency visitMiller Electric Mfg. Co Your distributor and/or equipment manufacturer’s

6-4. Jog/Purge Switch

6-5. Front Panel Controls

See

Time (sec)

Section

OM-230 009 Page 22