Manuals / Miller Electric / Power Tools / Welder

Miller Electric PipePro Dual manual Introduction, Symbols And Definitions, Specifications, Rating

Models: PipePro Dual

1 48

Download 48 pages 56.03 Kb

Page 16

Image 16

3-2. Symbols And Definitions

.Some symbols are found only on CE products.

A	Amperes	V	Volts		Alternating Current	X	Duty Cycle
IP	Degree Of	Hz	Hertz		Program		Wire Feed
	Protection		Hertz		Program		Wire Feed
	Protection
	Jog		Output		Trigger		Line Connection
	Set Up		Sequence		Trigger Hold On		Trigger Hold Off
	Purge		Press To Set		Start		Crater
	Time		Preflow Time		Postflow Time		Read Instructions
U1	Increase	I1	Primary Current	I2	Rated Current	U2	Load Voltage
U1		B
	Primary Voltage	A	Dual Schedule
	Primary Voltage		Dual Schedule

SECTION 4 − INTRODUCTION

4-1. Specifications

Type of Input	Welding Power	Wire Feed Speed	Wire Diameter	Welding	IP	Overall
Type of Input	Welding Power	Wire Feed Speed	Wire Diameter	Circuit	IP	Overall	Weight
Power	Source Type	Range	Range	Circuit	Rating	Dimensions	Weight
Power	Source Type	Range	Range	Rating	Rating	Dimensions
				Rating

40 Volts DC	PipePro 450 RFC with	50 To 780 ipm	.023 To 1/8 in	100 Volts,	IP 21	Length: 35 in	87 lb
10 Amperes	14-Pin And Contactor	(1.3 To 19.8 mpm)	(0.6 To 3.2 mm)	750		(889 mm)	(39.5 kg)
	Control			Amperes,		Width: 12-1/2 in
			Max Spool	100% Duty		Width: 12-1/2 in
			Max Spool	100% Duty		(318 mm)
			Weight: 60 lb	Cycle		(318 mm)
			Weight: 60 lb	Cycle		Height: 14 in
			(27 kg)			Height: 14 in
						(356 mm)

OM-230 009 Page 12

Page 16

Image 16

Miller Electric PipePro Dual manual Introduction, Symbols And Definitions, Specifications, Rating

Contents

OM-230 009F ProcessesDescription File MIG GmawFrom Miller to You Table of Contents Page Symbol Usage Arc Welding HazardsElectric Shock can kill HOT Parts can cause severe burnsFumes and Gases can be hazardous ARC Rays can burn eyes and skinWelding can cause fire or explosion Flying Metal or Dirt can injure eyesWelding Wire can cause injury Fire or Explosion hazardFalling Unit can cause injury Moving Parts can cause injuryPrincipal Safety Standards California Proposition 65 WarningsEMF Information About Implanted Medical DevicesSymboles utilisés UNE Décharge Électrique peut entraîner la mortLES Fumées ET LES GAZ peuvent être dangereux DES Pièces Chaudes peuvent provoquer des brûlures gravesLE Soudage peut provoquer un in cendie ou une explosion LE Bruit peut endommager l’ouïe LES Bouteilles peuvent exploser si elles sont endommagéesRisque D’INCENDIE OU D’EXPLO- Sion LA Chute DE L’APPAREIL peut blesserLES Fils DE Soudage peuvent provoquer des blessures Proposition californienne 65 AvertissementsLE Soudage À L’ARC risque de provoquer des interférences Information EMF Principales normes de sécuritéEn ce qui concerne les implants médicaux OM-230 009 Disconnect input plug or power before working on machine − DefinitionsDrive rolls can injure fingers Keep your head out of the fumesSymbols And Definitions Specifications− Introduction Rating− Installation Typical Connection Diagram For MIG EquipmentTypical Connection Diagram For TIG Equipment Typical Connection Diagram For Stick Equipment Rear Panel Connections And Rotating Drive Assembly Pin Plug Information Pin Pin InformationInstalling And Threading Welding Wire Setting Internal DIP Switches Current Detect Override OFF Factory Default S1-1 And S1-2Right Side Motor Control Board PC1 Left Side Motor PC101 Automatic Run-In OFF S1-1 And S1-2Factory Set Default Settings For DIP Switches S1 And S4 Display Board DIP Switch SettingsTools Needed Remove wrapper DIP Switch S1 And S4 Power Switch Left/Right Select Switch− Operation Operational TermsJog/Purge Switch Front Panel ControlsSee Time secProgram Push Button Upper DisplayUpper Display Upper Display Push ButtonSetup Push Button Lower DisplayAdjust Control Welding Sequence DiagramSequence Push Button WeldAuxiliary Menus Wire Feed Speed Units When the Setup button is pressed again, the menu repeatsRange Locks Software Revision LevelRemote-14 Receptacle Information At the same time, as both− Setting Sequence Parameters − Setting Dual Schedule ParametersOptional Dual Schedule Switch Diagrams Sequence Parameters In a ProgramIndicates a com Indicates a trigger Munication error Error DiagnosticsLED3-Related Error Indications − Maintenance & Troubleshooting Routine MaintenanceDisconnect power before maintaining = Check ~ = Clean = Replace Reference EveryDisconnect power before troubleshooting TroubleshootingTrouble Remedy Material Thickness Gauge − Electrical Diagram Circuit Diagram229 867-A − Parts List 21 −2Part Description Quantity Control Box GS1,101 219 Drive Assembly, Wire Drive Assembly, Wire -1Item203 Drive Roll And Wire Guide Kits Fraction Metric Kit Roll Wire SizeRoll Drive Roll Drive KitYour distributor also gives ServiceSupport To locate a Distributor or Service Agency visit Miller Electric Mfg. CoFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s

3-2. Symbols And Definitions

.Some symbols are found only on CE products.

Time

SECTION 4 − INTRODUCTION

4-1. Specifications

Rating

40 Volts DC

OM-230 009 Page 12