Bloomfield 1012, 1040 Brew Time Adjustment, Dripout Time Adjustment, Remove Tank LID Assembly

Page 18

SERVICING INSTRUCTIONS (continued)

IMPORTANT: Water pressure must be between 20 p.s.i and 90 p.s.i. flowing pressure.

If water pressure exceeds this value, or if water pressure varies greatly, a pressure regulator must be installed in the water supply line.

Fig. 15 Adjust BrewTime and Dripout Time

IMPORTANT: Before setting assembly into tank, make sure tank lid gasket is properly seated on flange of lid.

DO NOT OVER-TIGHTEN.

IMPORTANT: When replacing temperature probe, be sure a new seal washer is in place around the probe. Tighten jamb lock nut only enough to ensure no water leakage. Excessive tightening is not necessary.

IMPORTANT: When replacing heating element, also replace seal gaskets.

BREW TIME ADJUSTMENT

The amount of water dispensed automatically during a brew cycle is controlled by the SOLENOID TIME dial of the controller.

Place empty decanter under brew chamber. Press BREW button. Brewer should dispense one full decanter of water. To adjust amount:

Remove brew chamber and button plug. On the controller, adjust SOLENOID TIME dial (BREW TIME); clockwise increases time. Run several cycles to check amount of water delivered.

DRIPOUT TIME ADJUSTMENT

Water delivered to the brew chamber will take a while to drip through as coffee. The time between the end of a brew and when a new brew can be initiated is controlled by the BREW SIGNAL TIMER. Adjust the BREW SIGNAL TIMER dial on the controller to account for the dripout time. Replace button plug.

REMOVE TANK LID ASSEMBLY

Unplug brewer or turn circuit breaker OFF. Turn OFF water supply. Remove top panel. Pull vent tube and inlet elbow out of basin pan.

On automatic models, pull water inlet tube out of basin pan. Remove basin pan.

On models with faucet, disconnect inlet pipe at faucet shut-off valve and outlet pipe at faucet.

Disconnect all wiring from hi-limit and heating element. Disconnect temperature probe from controller.

Loosen center screw on tank hold-down bracket. Remove hold-down bracket by sliding short slotted end off of locking stud and lifting it off. Remove cover assembly by lifting it straight up.

Reassemble in reverse order.

REPLACE TEMPERATURE PROBE

Unplug brewer or turn circuit breaker OFF. Remove top panel.

Loosen and free jam nut from pass-thru fitting securing temperature probe. Disconnect temperature probe wiring connector from controller.

Lift out probe, jamb nut and gasket. Reassemble in reverse order.

REPLACE HEATING ELEMENT

Remove tank lid assembly per above.

Remove two hex nuts holding element to cover. Pull element from mounting holes.

Reassemble in reverse order.

16

641 75844 Owners Manual E.B.C. Decanter

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Electronic Brew Control Warranty Statement Table of Contents SpecificationsApplicability Features and Operating Controls Electrical Damage Precautions and General InformationAgency Listing Information Burn HazardEquipment Hazard Installation InstructionsPLUMBER’S Installation Instructions Leveling the UnitInstallation Instructions ELECTRICIAN’S Installation InstructionsOperation START-UPWater Heater Brew Cancel Electronic FeaturesBrew Settings Energizing the BrewerOver-Temperature and Temperature Fault Protection Quality TimerDisable/Enable After Hours Feature After Hours OperationAutomatic Operation Brewing CoffeePreparation WarmersCleaning Instructions Electric Shock HazardTroubleshooting Suggestions Symptom Possible Cause Suggested RemedyError Detection Electric Shock HazardWhat to Check Description Corrective Action Access Panels Servicing InstructionsTemperature Adjustment Servicing InstructionsRemove Tank LID Assembly Brew Time AdjustmentDripout Time Adjustment Replace Temperature ProbeReplace HOT Water Faucet Coil Replace SolenoidReplace Faucet Supply Hose Repair HOT Water FaucetController Hook-Up Replace ControllerReplace Power Board SET Controller JumpersReplace Keypad Procedure Delime the Water Tank Servicing Instructions Exploded View & Parts List Exploded View & Parts List Exploded View & Parts List Bloomfield Paper Filter pk 1072 HOT Water Tank Assembly DescriptionElectrical Components Description Used onInternal Plumbing Components Wiring Diagram Wiring Diagram Wiring Diagram Telephone Fax

1072, 1040, 1012 specifications

Bloomfield 1040, 1012, and 1072 are three models that exemplify advanced technology and features in the realm of versatile machinery and equipment. Each model is tailored to meet specific operational needs while ensuring efficiency and performance.

The Bloomfield 1040 is renowned for its robust design and user-friendly interface. This model incorporates a powerful engine that guarantees high torque and speed, making it ideal for heavy-duty tasks. Its advanced control system allows for precise maneuverability, which is essential for applications in confined spaces. Additionally, the 1040 comes with a high-capacity fuel tank, ensuring prolonged operational time without the need for frequent refueling.

In terms of technology, the 1040 is equipped with state-of-the-art diagnostic capabilities. This feature enables users to monitor the machine's performance in real time, identifying potential issues before they escalate into costly repairs. The model also includes an intuitive digital display that provides vital information such as fuel levels, engine temperature, and maintenance reminders.

The Bloomfield 1012 model focuses on portability and ease of use. Weighing less than many competitors, the 1012 is designed for easy transport, making it perfect for landscaping, construction, and maintenance tasks. Its compact size does not compromise on power, as it features a high-efficiency engine that balances performance with fuel economy.

Moreover, the 1012 integrates wireless connectivity, allowing operators to control and monitor the machine remotely. This advancement significantly enhances productivity by streamlining operations and reducing downtime.

Lastly, the Bloomfield 1072 stands out with its innovative safety features. Equipped with multiple sensors and automated shut-off capabilities, this model prioritizes operator safety. The enhanced visibility offered by its design ensures that users maintain awareness of their surroundings while operating.

Furthermore, the 1072 includes built-in load monitoring systems that aid in preventing overload scenarios, prolonging the lifespan of the equipment.

In conclusion, Bloomfield 1040, 1012, and 1072 each bring unique features and enhancements to the table. Whether users prioritize power, portability, or safety, Bloomfield's commitment to quality and technological advancement ensures that operators will find a suitable solution within this lineup. These models not only enhance productivity but also promote efficiency, making them valuable assets in any operational context.
Top Page Image Contents