Bloomfield WVOC-2HSG, WVOC-2HFG operation manual Maintenance Instructions, Hinge Adjustment

Page 26

MAINTENANCE INSTRUCTIONS (continued)

CLEARANCES

EQUAL

APPROXIMATELY

TOP PANEL

CHECK ALIGNMENT

BOTTOM

PANEL

C. HINGE ADJUSTMENT

1.The hinges provide the pivot for the door, allow for height adjustment and alignment so that the door closes properly on the gasket.

2.To access the hinge adjustments:

a.Remove the grease tray. Remove the upper trim panel by removing the four screws at the ends of the panel. The trim panel / grease tray support assembly will then pull straight out.

b.Remove the bottom trim panel by removing the four screws at the ends of the panel, and by loosening the two screws holding the bottom door gasket. The panel will then pull straight out.

3.The door should be approximately centered between the upper and lower lips of the cabinet. Adjust the door for height:

a.The hinge sleeve acts as a jam nut for the height adjuster.

b.The top and bottom clearances should be approximately equal. If necessary, loosen the hinge sleeve and turn the height adjustment nut until the required clearances are achieved.

c.Retighten the hinge sleeve.

4.Check fore-and-aft adjustment in two places on the hinge-side of the door. Use a piece of paper (such as a dollar bill) between the inner surface of the door and the door gasket. The paper should be definitely held, but should be able to be pulled out with just a slight drag.

5.To adjust a top or bottom hinge:

a.Loosen the holding bolts.

b.Tighten or loosen the adjusting bolt as needed to achieve the proper vertical clearances.

c.Retighten the holding bolts.

d.Recheck the clearances. Recheck the tightness of the bolts.

6.Reassemble the trim panels. Remember to retighten the screws for the lower gasket

 

HINGE SLEEVE

HINGE BRACKET

HINGE BRACKET

HOLDING

HOLDING

BOLTS

BOLTS

DOOR PIVOT

HEIGHT

ADJUSTING

ADJUSTMENT

BOLT

ADJUSTING

 

 

BOLT

24

Page 25 Page 27
Image 26
Page 25 Page 27
Contents 505 Important do not Discard this ManualLimited Warranty Statement Introduction Table of ContentsSpecifications Features & Operating Controls Ventilator Section Description CommentFeatures & Operating Controls Description Comment Ventilator Section ControlsCooking Appliance Controls Precautions and General Information Electric Shock hazardSTD Agency Listing InformationOperational Notes Unpacking & Inspection InstallationSetup This is Responsibility Installer Service Technician Installation NotesElectrical Installation Electric Shock HazardAuthority Having Jurisdiction Fire Suppression System InstallationFire Hazard Filters Installation Filter InstallationOven Rack Installation Grease Trough and Grease CUP InstallationHotplate Drip PAN Installation Spiral Heating Elements only Do not Operate Unless Grease CUP is InstalledPRE-FILTER Element Ventilator OperationOperation Hot SurfaceGriddle Product Temp Time Minutes Suggested Cooking TimesConvection Oven Product Temp Time Number Minutes Racks Convection Oven Operating Instructions Manual Cook ModeProgram Cook Mode Electrical Shock HazardBurn Hazard Temperature Offset ModeGriddle Operating Instructions SeasoningHotplate Operating Instructions Cooking with Your HotplateCleaning Instructions Convection Oven Cleaning InstructionsGriddle Cleaning Instructions Griddle ExteriorFrequency Hotplate Cleaning InstructionsPrecautions ToolsPreparation Ventilator Section Cleaning InstructionsCleaning Frequency WeeklyTroubleshooting Suggestions Latch Adjustment Maintenance InstructionsFAN Cleaning Personal Injury HazardMaintenance Instructions Hinge AdjustmentTemperature Calibration Ansul Health Hazards Page Page Maintenance Schedules Fire HazardDescription Service

WVOC-2HFG, WVOC-2HSG specifications

The Bloomfield WVOC-2HSG and WVOC-2HFG models represent the cutting edge in advanced automation and control systems designed for diverse industrial applications. These systems serve as pivotal tools for optimizing processes, enhancing efficiency, and ensuring precise monitoring of various operations across numerous sectors.

One of the main features of the Bloomfield WVOC-2HSG and WVOC-2HFG is their dual functionality, which allows for simultaneous management of multiple process parameters. The WVOC-2HSG variant is tailored for high-speed data acquisition and processing, making it suitable for environments where real-time monitoring is crucial. In contrast, the WVOC-2HFG offers enhanced flexibility with its feature-rich interface and robust control capabilities, catering to applications that demand customization and adaptability.

Both models leverage advanced technologies such as Internet of Things (IoT) connectivity, enabling seamless integration with existing infrastructure. This connectivity facilitates remote monitoring and control, allowing operators to access data from anywhere, thus improving decision-making and response times. The cloud-based analytics feature further empowers users to generate insights from historical data, leading to better predictions and proactive maintenance strategies.

In terms of characteristics, the Bloomfield WVOC-2HSG and WVOC-2HFG systems come equipped with high-resolution displays and intuitive user interfaces. These interfaces are designed to minimize the learning curve for new users while providing seasoned operators with the tools needed for complex tasks. The systems also include a variety of input and output options, making them compatible with a wide array of sensors and actuators.

Durability is another significant characteristic of these models, as they are engineered to withstand challenging industrial environments. Built with rugged materials, they are resistant to dust, moisture, and extreme temperatures, ensuring reliable performance over time.

Moreover, safety features are seamlessly integrated into these systems, with built-in alarms and redundancy mechanisms designed to prevent operational failures. This commitment to safety underscores Bloomfield's dedication to providing not only performance but also peace of mind for operators.

In conclusion, the Bloomfield WVOC-2HSG and WVOC-2HFG models stand out as premier solutions in industrial automation, showcasing a blend of innovative technology, user-centric design, and enhanced durability. Whether for real-time data processing or flexible control capabilities, these systems are set to redefine standards in operational efficiency and reliability across various industries.
Top Page Image Contents