Cecilware GB-IT operation manual Definition of Error Screens and Troubleshooting

Page 15

DEFINITION OF ERROR SCREENS AND TROUBLESHOOTING

IF ANY OF THESE ERROR SCREENS COME UP ALSO CHECK THE SAFETY RELAY IN ADDITION TO THE COMPONENT IN QUESTION. SEE RELAY TEST.

1.Over Temperature Error Screen

Definition – This screen is displayed and the system is shut down when the present water temperature is sensed higher than 208 °F.

Possible Causes: Invalid required Water Temperature or Faulty Water Temperature Sensor.

2.Water OverflowError Screen

Definition – This screen is displayed and the system is shut down when the OT/OF Sensor is detecting a rapid change in ambient temperature inside the overflow tube.

Possible Causes: Faulty fill Solenoid or faulty/ disconnected Level Sensor.

3.No Fill Response Error Screen Definition – This screen is displayed and the system is shut down when the Fill Solenoid has been continuously energized (open & filling) for more than five minutes during the first fill or more than 30 seconds thereafter.

Possible Causes: Water supply is turned OFF or faulty / disconnected Level Sensor.

4.No Temperature Response Error Screen

Definition – This screen is displayed and the system is shut down when the Water Heater has been continuously energized (heating) for more than 30 minutes .thereafter.

SYSTEM ERROR!

OVER TEMPERATURE

!SYSTEM ERROR!

WATER OVERFLOW

!SYSTEM ERROR!

NO FILL RESPONSE

!SYSTEM ERROR!

NO TEMP RESPONSE

Possible Causes:

faulty/disconnected Level Sensor, faulty Water Temperature Sensor, or faulty Water Heater.

5. Water Heater Error Screen

 

!SYSTEM ERROR!

Definition – This screen is displayed and the system is shut down when the required status (ON/OFF) of

WATER HEATER

the Water Heater does not match the sensed status for more than two seconds.

 

Possible Causes:

 

 

faulty/disconnected Water Heater, faulty/disconnected Triac, or faulty/disconnected Safety Relay.

6.Fill Solenoid Error Screen – Water Inlet Valve

Definition – This screen is displayed and the system is shut down when the required status (ON/OFF) of the Fill Solenoid does not match the sensed status for more than two seconds.

!SYSTEM ERROR!

FILL SOLENOID

Possible Causes: Faulty/disconnected Fill Solenoid or faulty/disconnected Safety Relay.

7.

Auger Motor Error Screen

 

!SYSTEM ERROR!

 

Definition – This screen is displayed and the entire system is inoperable when the required status

 

AUGER MOTOR

 

 

 

 

 

(ON/OFF) of the Auger Motor (identified by @) does not match the sensed status for more than two seconds.

 

 

Possible Causes: Faulty/disconnected Auger Motor.

 

8.

Dump Solenoid Error Screen – Dispense Valve Error Screen

 

 

 

!SYSTEM ERROR!

 

Definition – This screen is displayed and the entire system is inoperable when the required status

 

DUMP MOTOR # @

 

 

 

 

(ON/OFF) of the Dump Solenoid (identified by @) does not match the sensed status for more than two seconds. Possible Causes: Faulty/disconnected Dump Solenoid [Dispense Valve] or faulty/disconnected Safety Relay.

9.Mixer Motor Error Screen

Definition – This screen is displayed and the entire system is inoperable when the required status

!SYSTEM ERROR! MIXER MOTOR # @

(ON/OFF) of the Mixer Motor (identified by @) does not match the sensed status for more than two seconds. Possible Causes: Faulty/disconnected Mixer Motor or faulty/disconnected Safety Relay.

If Mixer Motor or Relay check out good, manually check for loose connections or defective parts on all 120V ac circuits including: fuse, fuse holder, transformer, hi-limit, and harness.

15

Image 15
Contents GB-IT Intelligent Technology Unpacking Instructions Mechanical SpecificationsElectrical Specifications Installation InstructionsFor Soup START-UP ProcedureFor Cappuccino For CoffeeWater Level Controls GB3M-5.5-IT Dimensions & Conponents Location ILL. aAdjustments ILL. B Features and Benefits of the Digital Dispenser Controller Parameter Definitions for System Software Version OFF Programming Instructions ILL. C Initializing ModeNormal Mode Rinse ModePortion control Program ModeTeach Me Timer Setup FunctionsGeneral Conventions Service ModeGram Throw Select a KEY Rinse Lockout Definition of Screens During Normal Operation Definition of Error Screens and Troubleshooting Communications Failure Screen Over Temperature / Over Flow Error ScreenCommunications Error Screen TestsCheck ALL Chamber Mounts for Signs of Wear Recommended Preventive MaintenanceClean OUT Vent MOTOR, Trough and Tubing Check ALL Dispense Valves for Lime BUILD-UPTo replace the Fluorescent Bulb Cleaning SANITIZING, Cleaning and Refilling HoppersHopper and Dispensing Chamber Assys with Wire Augers ILL. E Hopper and Dispensing Chamber Assy with Nylon Augers ILL. E Set Temperature at 195F See Programming Instructions Problem Probable Cause RemedyTank ASS’Y ILL. F Description QTY Door ASS’Y with Components GB3M5.5 IT Shown ILL. GDescription GB3M-10-ITPage Description GBM-5.5-IT Common Parts Identification ListPage Page Page Page Page Page Using Older Version of Touch PAD with ONE Ribbon Connector Using Older Version of Touch PAD with ONE Ribbon Connector

GB-IT specifications

The Cecilware GB-IT is a cutting-edge coffee brewing system designed to cater to the needs of cafes, restaurants, and other commercial establishments that require efficiency, speed, and quality in coffee production. This machine stands out for its robust construction and the use of advanced technologies, making it a reliable choice for high-demand environments.

One of the primary features of the Cecilware GB-IT is its dual-purpose capability, functioning as both an automatic brewer and a tea brewer. This versatility allows businesses to serve a wide range of hot beverages without needing multiple machines, ultimately saving space and reducing operational costs. The GB-IT has a generous brewing capacity, typically handling up to 3 gallons of coffee in a single batch, which is essential for busy service periods.

The machine is equipped with a unique digital brew control that allows users to set precise brew times and temperatures. This feature ensures that each cup of coffee is brewed to perfection, providing a consistent flavor profile that loyal customers can rely on. Additionally, the GB-IT comes with programmable volumes, allowing operators to customize the amount of coffee brewed based on their specific needs and customer demand.

Another notable characteristic of the Cecilware GB-IT is its durable construction. Built with high-quality stainless steel, the machine not only has an appealing aesthetic but is also designed to withstand the rigors of daily use in a bustling commercial environment. Its compact footprint allows it to fit seamlessly into any kitchen setup, maximizing counter space while still delivering high performance.

The GB-IT also incorporates advanced safety features, including an automatic shut-off system that activates when the water reservoir runs low or the brewing cycle is complete. This thoughtful design minimizes the risk of overheating and ensures the longevity of the machine.

In terms of maintenance, the Cecilware GB-IT is designed for easy cleaning and servicing, with components that can be easily accessed. This ensures that operators can perform routine maintenance without significant downtime, contributing to overall operational efficiency.

In summary, the Cecilware GB-IT stands as an excellent solution for businesses that prioritize quality, efficiency, and versatility in their beverage offerings. With its advanced features, durable construction, and user-friendly design, it is a worthwhile investment for any establishment looking to elevate their coffee and tea service.