Middleby Marshall PS536-Series installation manual Section Installation, Unloading

Page 13

SECTION 2

INSTALLATION

SECTION 2

INSTALLATION

NOTE: The oven, when installed, must be electrically grounded in accordance with local codes, or in the ab- sence of local codes, with the National Electrical Code (NEC), or ANSI/NFPA70.

NOTE

There must be adequate clearance between the oven and any adjacent combustible con- struction. Clearance must also be provided for servicing and for operation.

CAUTION

It is required that the oven be placed under a ventilation hood for adequate air supply and ventilation.

CAUTION

Do not obstruct the flow of combustion and ventilation air to and from your oven. Do not obstruct the ventilation holes in the Control Panel.

CAUTION

On ovens with the Machinery Drive Compartment located at the right end, a minimum clearance of 0″ to a left side wall, 18″ to a right side wall and 6″ from a back wall to air openings at the rear of the oven must be maintained. On ovens with the machinery/drive compartment located at the left end, a minimum clearance of 0″ to a right side wall, 18″ to a left side wall and 6″ from a back wall to air openings at the rear of the oven must be maintained.

For servicing and cleaning, a minimum of 18″ clearance from all walls is recommended.

I. UNLOADING

Your Middleby Marshall PS536ES-Series Oven is shipped partially assembled. It will arrive in a carton on a crate.

Carton size for a PS540-Series Oven is:

58″ (2134mm) Long ×

47.25″ (1473mm) Wide ×

36″ (1118mm) High ×

The crate and carton must be examined before signing the Bill of Lading. Report any visible damage to the transport company, and check for the proper number of crates. If apparent damage is found, make arrangements to file a claim against the carrier. Surface Interstate Commerce Regulations (U.S.A.) require that the claim must be initiated by the consignee within 10 days from the date that the shipment is received.

APre-installationProceduresManual(MMP/N88910-0009) is attached to the exterior wall of the carton. This manual contains detailed instructions on unpacking and moving the oven(s) to the operating site. When the transport company notifiesyouofanimpendingdelivery,arrangetohaveaforklift at your facility to unload the carton(s).

Instructions for stacking the ovens is continued in a separate manual used by Middleby Marshall Authorized Installers.

If you have a door wider than the carton, simply move the carton into your facility and arrange an appointment with your Middleby Marshall Authorized Installer.

If your door is narrower than the carton, then the oven will have to be unpacked. Follow the directions shown in the Pre-Installation Procedures Manual.

9

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Owners operating Page Iii Middleby MarshallTable of Contents Model Identification Section DescriptionSeries PS536ES Electrical Specifications PS536ES Series Oven SpecificationsDimensions General specifications per oven cavityHeat Transfer and How It Works II. Principle of AIR FlowAir Fingers II. Principle of AIR FlowIII. Component Function Figure PS536ES-Series Oven Components LocationsIII. Component Function Cooling Fan F2. Blank Plates Blank Plates two sizes and an Air FingerUnloading Section InstallationInstallation PS536ES Oven Installation Required Kits and EquipmentInstallation KIT see Figure Model PS536ES Single Oven Dimensions Model PS536ES Double Oven Dimensions Model PS536ES Triple Oven Dimensions Restraint Cable InstallationInstallation II. Ventilation Guidelines 11. Typical Electric Oven Data Plate IV. Electric Supply for Electrically Heated Ovens13. Installing Rear and End Stops VI. Conveyor Rear Stop and END Stop InstallationControl Functions Section OperationII. Component Information and Location Figures 3-1 Conveyor Measuring Conveyor SpeedSee Figures 3-4 Power Failure Startup Procedures Daily StartupShutdown Procedure III. STEP-BY-STEP OperationLocation and Description of Controls II. Normal Operation STEP-BY-STEP III. Quick Reference Digital Temperature Controller Symptom IV. Quick Reference TroubleshootingSection Maintenance Exterior Maintenance DailyCooling Fan Crumb Pans FigureII. Maintenance Monthly Section Maintenance Standard Fingers Air Fingers Disassembly For CleaningReassembly of Air Fingers Cleaning the WindowBack in the same way they came out Section Maintenance Reinstall End Plugs Checking Conveyor Belt Tension Conveyor Reassembly Into OvenConveyor Belt Link Removal Attaching Drive Chain Replacing Conveyor BeltLower End Plug Cleaning the Blower/Fan Motor III. Maintenance Every 3 MonthsVentilation Electrical TerminalsSplit-belt Conveyor Shaft Cleaning Section Maintenance Important Notices IV. Maintenance Every 6 MonthsKEY Spare Parts KIT Section Troubleshooting Section Troubleshooting Parts List Parts List QTY Description Oven PANELS, Window and LegsParts List English Parts List Blower and Shroud Parts List Item QTY Conveyor Description ConveyorParts List Split Belt Conveyor Element Machinery Compartment Section Parts List Electrical Electrical Section Schematics Electrical Schematics Section Hour Service Hotline
Top Page Image Contents