Middleby Marshall PS360-U installation manual III. Assembly, IV. Thermocouple Installation

Page 8

SECTION 2 - INSTALLATION

ENGLISH

III. ASSEMBLY

A.Caster Removal

After moving the ovens in to the installation location, remove the casters attached to each oven cavity. These casters are provided for pre-installation movement ONLY.

B.Stacking

If the installation will include upper ovens mounted atop lower ovens, stack the oven cavities.

C.Stands

If the installation includes ovens that are to be mounted on stands, assemble the ovens to the stands at this time. An exploded view of the stand is shown in Figure 2-3.

D.Flue Vent(s)

For gas ovens, attach one flue vent to the rear wall of each oven cavity. Use one #10-16 x 3/8" and two #10-32 x 3/4" screws for each flue vent. These screws are provided in the Installation Kit.

IV. THERMOCOUPLE INSTALLATION

1.Install one thermocouple sensing bulb into each of the two holes in the rear panel of the oven, as shown in Figure 2-4. Fasten each thermocouple in place using one of the #10- 32 x 3/8" screws supplied in the Installation Kit.

2.Thread BOTH sets of thermocouple leads through the grommet and into the machinery compartment, as shown in Figure 2-4.

3.Remove the right-side access panel of the machinery compartment.

4.Thread the thermocouple leads through the side of the machinery compartment as shown in Figure 2-5, and into the electrical box (at the right-front of the machinery compart- ment).

5.Connect BOTH sets of thermocouple leads to the tempera- ture controller as shown in Figure 2-6. Note that the two thermocouples are now tied together at the temperature controller.

6.Replace the right-side panel of the machinery compart- ment.

7.Repeat Steps 1-6 for any other oven cavities in the installa- tion.

Figure 2-3 - Exploded View, Oven Stand

Attachment

plates inc. w/

upper oven

installation kit

Figure 2-4 - Thermocouple Installation Locations

Thermocouples

Grommet-protected hole

Figure 2-5 - Placing the Thermocouple Leads

Figure 2-6 - Thermocouple Lead Connections

8=White=Positive

7=Red=Negative R=No Connection

Ground=Shielded cable

8

Image 8
Contents Rev. B V1 7/01 PS36040kW 50kW 2x40kW 2x50kW 26kW 2x26kWFor Your Safety EnglishTable of Contents Oven Uses III. Oven SpecificationsDescription English Gas orifice and pressure specifications per oven cavity InstallationElectrical specifications per oven cavity Installation KIT Installation kit components one kit required per cavityAdditional installation kit components for gas ovens 710II. Ventilation System RequirementsRecommendations Other ventilation concernsIII. Assembly IV. Thermocouple InstallationConveyor Installation Removing the Conveyor Drive SprocketVI. Final Assembly 11 Conveyor and Master Link OrientationVII. Electrical Supply VIII. GAS SupplyAdditional Information Gas Ovens Additional Information Electric OvensGas Line Gas Utility Rough-In RecommendationsGas Meter Preparation for Use with Various Gases Replacing the Gas Orifices if so requiredAdjusting the Orifice Manifold Pressure and Heat Input Volumetric MethodChecking the Gas Supply Inlet Pressure Orifice Manifold Pressure MethodConveyor Switch Turns the conveyor drive motor on and off Reset Switch Gas ovens only. IlluminatesOperation Location and Description of ControlsII. Normal Operation STEP-BY-STEP III. Quick Reference Digital Temperature Controller IV. Quick Reference Troubleshooting SymptomMaintenance Maintenance DailyII. Maintenance Monthly Removing the ConveyorIII. Maintenance Every 3 Months Split Belt Disassembly and CleaningIV. Maintenance Every 6 Months 10 Key Spare Parts KitDiagrams 400V, 50 Hz, 1 PhGas Oven 230V, 50 Hz, 1 Ph