Conair GB, WSB manual Safety Hazards MIX Blades, Additional MIX Blade Hazard, Hopper Finger Guards

Page 5

 

SAFETY HAZARDS

 

+

-----------------------------------------------------------

+

¦

MIX BLADES

¦

¦

 

¦

¦

Mix blades are driven with substantial torque.

¦

¦

 

¦

¦

NEVER place your hand in the mix chamber

¦

¦

while blades are turning.

¦

¦

 

¦

¦

SERIOUS INJURY will result.

¦

+

-----------------------------------------------------------

+

+

-----------------------------------------------------------

+

¦

ADDITIONAL MIX BLADE HAZARD

¦

¦

 

¦

¦

Over time, mix blades may become RAZOR SHARP.

¦

¦

 

¦

¦ Always be careful when TOUCHING or CLEANING these blades. ¦

¦

 

Check for sharp edges frequently.

 

¦

¦

 

Replace blade if a hazard exists.

 

¦

+

-----------------------------------------------------------

 

 

 

+

+

-----------------------------------------------------------

 

 

 

+

¦

 

 

SLIDE VALVES

 

 

¦

¦

 

 

 

 

 

¦

¦

Slide valves in hoppers SLAM CLOSED without warning.

¦

¦

 

They WILL injure your fingers.

 

¦

¦

 

 

 

 

 

¦

¦

ALWAYS keep fingers clear of slide gate openings.

¦

¦

NEVER use your fingers to clear an obstruction.

¦

¦

NEVER use your fingers to move a sticking slide gate.

¦

+

-----------------------------------------------------------

 

 

 

+

 

 

 

SAFETY FEATURES

 

 

 

+

-----------------------------------------------------------

 

 

 

+

¦

 

SAFETY INTERLOCK SWITCH

 

¦

¦

 

 

 

 

 

¦

¦

The ACCESS DOOR is equipped with a safety interlock

¦

¦

switch that prevents the mix motor from running and

¦

¦

 

the slide valves from opening.

 

¦

¦

 

 

 

 

 

¦

¦

 

DO NOT defeat this safety switch.

 

¦

+

-----------------------------------------------------------

 

 

 

+

+

-----------------------------------------------------------

 

 

 

+

¦

 

HOPPER FINGER GUARDS

 

¦

¦

 

 

 

 

 

¦

¦

Finger guards are fitted into each hopper compartment.

¦

¦

 

DO NOT reach through these guards.

 

¦

¦

 

DO NOT use your fingers to clear an

 

¦

¦

 

obstruction below these guards.

 

¦

¦

 

 

 

 

 

¦

¦

 

DO NOT remove these guards.

 

¦

+

-----------------------------------------------------------

 

 

 

+

 

+---------------------------------------------

 

 

+

 

 

¦

PROCEED TO:

ASSEMBLY

NEXT PAGE

¦

 

 

+---------------------------------------------

Part 4

 

+

 

 

 

 

 

 

 

Image 5
Contents Gravimetric Blenders Date Manual Number UGB007/1103 Serial numbers Model numbers Part Hardware Maintenance Part Troubleshooting / SoftwareTwelve Component Software Part OperationSpecial Features Check OUT ProcedureProceed to Safety Hazards Next Slide ValvesSafety Features Safety Interlock Switch Safety Hazards MIX BladesProceed to Assembly Next Additional MIX Blade HazardDisclaimers Part I Assembly Page Proceed to Check OUT Procedure Next Wiring ConsiderationsTurn Power on Procedure What should Happen Plug in ControllerAT this Point Touch Weigh BIN Very LightlyFacing the Controller Side of the Blender Press Alarm KEYALL Models Press Dump KEYPage Password Weigh BIN Load Cell Grams Dimensions Rating GBMSelecting Correct Model Model Batch WTCAL OFF Part II Operation Load Cell CalibrationCAL ZeroNatural Ratio to Each Other Turning on Outputs Material TypesRegrind Percent of MIX Regrind Additive Percent of ALL NaturalsNatural SET= On the Other HandProceed to Rate Calibration Next TypesRate Calibration YOU Dont have to do this Proceed to Entering Settings NextOper OperateSET Other Natural SettingsEntire MIX Thumbwheel Assignments this is OptionalMicro Pulse Selected Models Special InstructionsGB/WSB GBM GB/WSB 240RPower on Power OFFInstructions for Normal Operation After Several Days of Proper OperationNormal Operating Sequence Each Cycle Wait 5 seconds, until display says Press Display will say Eight Character Display Alarm Silence Strobe Light and Beeper AlarmsROM OK LED LightsMixer Motor Outlet Mixer Motor ON/OFF/TIMED SwitchInternal Fuses Thumbwheel SwitchesKeypad Summary Description Keypad Description of Functions Keypad Automatic Operation ModeTotal RecipeBtch BatchFast Batch CountOperator TAGKeypad Manual Mode Time TimedPage Keypad Program Mode TRC FLG 1TY 2TY 3TY CTY MIX 1CS 2CS 3CSPara ViewYLD Ctrl Page Eeprom ExplanationPage Page Page Page Page Page MIX Time ParametersParameter List Brief Explanations Page OFF Designates Material Type Component ParametersPage FLG Parameter List Full ExplanationsJOG KDF, WDF ROV Page Page Dispense Station Configuration Tare Weight Do not Change These STLXTP XCV + XRCTCV + TRC CPL XALXUL MCT MPOLIQ REG = Regrind NAT = Natural ADD = Additive OFF =Not Used Page Page Page Page Page Page FLG MIX JOG Parameter Default Settings Twelve SoftwareFCV DTI KDF WDF BER ROC ROV RHL FUL1MI 1NC 1PT 1RP 1RD 1TY = OFF 1CS 1AL 1XT 1SE1LA 1PO 3TY 3CS 3AL 3XT 3SE 3WTChanging Parameters Prnt Prnt OFFFinal DISP,% Rate GR/TIMEFinal DISP,% What to Check for Page Page Page Calibrate Comp Special TestsTime Comp PARAMETER, PRT Material Usage InformationDate Time Current Last PrintedPart IV Troubleshooting What to do Typical Problems Page Normal Operating Sequence Material Runs OUT Verifying Load Cell Function CNT Load Cell RAW Signal ReadoutCNT OFF Results to Expect Load Cell Weigh BIN TestCore Dump Clear RoutineClear ALL Restart Internal MIX Motor Level SensorWeigh BIN Dump Valve MIX Problems Page Full Recalibration of Load CellsDispense Gates Blender Preventive MaintenanceLoad Cells Weigh BinsPage Computer Outputs Wiring Supplement Page Call Appendix A-2 Gravimetric Batch Blenders Autoweigh GBM Series Models SpecificationsTOP View Front View Side View Gravimetric Batch Blenders AutoWeigh GB100 Series ModelsGravimetric Batch Blenders GB 220 and 420 Models 120V/1 phase/50-60 Hz 240V/1 phase/50-60 HzTOP View Mounting Interface Gravimetric Batch Blenders AutoWeigh GB240 and GB440 Models2124 Gravimetric Batch Blenders AutoWeigh GB900 Series ModelsGB1840 GB1860 Gravimetric Batch Blenders AutoWeigh GB1840 and 1860 ModelsControl Remote Mounted Models WSBM22 WSBM131 WSBM140 Gravimetric Batch Blenders Wsbm Series modelsSide View Front View Side View, R Model Front View, R Model Gravimetric Batch Blenders WSB 100 and 100R Models24.4 Gravimetric Batch Blenders WSB 220 and 420 ModelsWSB442 Gravimetric Batch Blenders WSB 240/440 and 240/440R ModelsGravimetric Batch Blenders WSB 1840, 1850 and 1860 Models Appendix C Appendix C Appendix C Appendix C Appendix C Appendix C Appendix C Appendix C

GB, WSB specifications

The Conair WSB,GB represents a cutting-edge advancement in hair styling technology designed for both professionals and everyday users. Known for its versatility, this styling device merges high-performance with user-friendly characteristics to deliver exceptional results.

One of the standout features of the Conair WSB,GB is its dual voltage capability. This allows users to take it anywhere in the world without worrying about voltage inconsistencies, making it an ideal travel companion. The device's sleek and portable design ensures that it is easy to pack while still being robust enough to handle regular usage.

The WSB,GB incorporates advanced heating technology that ensures rapid heat-up times, allowing users to get to styling quickly. With multiple heat settings, the device caters to various hair types and styles, whether it's coarse, fine, or color-treated hair. This customization is essential for achieving the perfect look while minimizing damage.

Another impressive characteristic of the Conair WSB,GB is its innovative ceramic technology. The ceramic plates distribute heat evenly, reducing hot spots that can lead to hair damage. This feature ensures that styling is not only efficient but also gentle on the hair, promoting a healthy shine and reducing frizz for a polished finish.

The device also boasts a swivel cord, which enhances convenience during use by allowing for free movement without the hassle of tangling. This ergonomic consideration is particularly beneficial for professional hairstylists who may need to maneuver around clients during appointments.

Safety is a crucial aspect of the WSB,GB design. It includes an automatic shut-off feature that turns the device off after a period of inactivity, providing peace of mind for users who might accidentally leave it on when finished.

In summary, the Conair WSB,GB offers various features that cater to the modern user’s needs. With its dual voltage, rapid heating capabilities, ceramic technology, swivel cord, and safety features, it stands out in the crowded hair styling market. Whether you’re a professional stylist or someone looking to elevate your everyday look, the WSB,GB is engineered to meet these demands with excellence.