Conair WSB, GB manual

Page 56

Sensors that we supply are wired correctly for this logic. If a "Bindicator" or similar device is used, with a micro-switch dry contact closure signal, then wire to the normally CLOSED contact so that the signal OPENS when regrind covers the bindicator paddle.

The circuit board "pin outs" for each sensor are positive, ground, and signal. If you are wiring using a dry contact closure, only the positive and signal lines are used. When the contact is open, the signal is pulled to ground internally through a resistor.

Example: RHL is set to 90 and 10 percent (RHL 09010). ROV last digit is set to zero, (ROV 10000).

The "Regrind" thumbwheel switch is set to 25 percent (025).

The Software logic is as follows:

If material level is high, above the high sensor, the HIGH sensor is COVERED, (returns NO signal); Regrind runs at the HIGH setting; 90 percent.

If material level is in the middle, between sensors, the High sensor is NOT covered, (returns a signal), the LOW sensor IS covered, (returns NO signal), Regrind runs at the THUMBWHEEL SETTING; 25 percent.

If material level is low, below the low sensor,

BOTH sensors are NOT covered, (both return a signal), Regrind runs at the LOW setting; 10 percent.

IF ROV equals 1 to 9 (ROV 10001 to ROV 10009):

All the same rules given above apply, except that the thumbwheel switch regrind setting does not jump in one step to a new setting, but, instead, moves slowly to the new setting which acts as a limit. The usage adjustment is made each cycle by the amount specified by the ROV parameter.

Example: RHL is set to 10 and 90 percent (RHL 09010). ROV last digit is set to 3 (ROV 10003).

The "Regrind" thumbwheel switch is set to 25 percent (025).

The Software logic is as follows:

If material level rises, goes above the high sensor, the HIGH sensor is COVERED,

Regrind usage will increase 3 percent each cycle up to a high limit of 90 percent.

If material level is in the middle, between sensors, the HIGH sensor is NOT covered,

the LOW sensor IS covered,

Regrind usage will change 3 percent each cycle, moving back toward the THUMBWHEEL SETTING of 25 percent.

If material level drops below the low sensor, BOTH sensors are NOT covered,

Regrind usage will decrease 3 percent each cycle down to a low limit of 10 percent.

Page 57

Page 55 Page 57
Image 56
Page 55 Page 57
Contents Gravimetric Blenders Date Manual Number UGB007/1103 Serial numbers Model numbers Part Troubleshooting / Software Part Hardware MaintenanceTwelve Component Software Part OperationCheck OUT Procedure Special FeaturesProceed to Safety Hazards Next Slide ValvesSafety Hazards MIX Blades Safety Features Safety Interlock SwitchProceed to Assembly Next Additional MIX Blade HazardDisclaimers Part I Assembly Page Wiring Considerations Proceed to Check OUT Procedure NextProcedure What should Happen Plug in Controller Turn Power onAT this Point Touch Weigh BIN Very LightlyPress Alarm KEY Facing the Controller Side of the BlenderALL Models Press Dump KEYPage Weigh BIN Load Cell Grams Dimensions Rating GBM PasswordSelecting Correct Model Model Batch WTPart II Operation Load Cell Calibration CAL OFFCAL ZeroNatural Ratio to Each Other Turning on Outputs Material TypesRegrind Percent of MIX Additive Percent of ALL Naturals RegrindNatural SET= On the Other HandTypes Proceed to Rate Calibration NextProceed to Entering Settings Next Rate Calibration YOU Dont have to do thisOper OperateOther Natural Settings SETEntire MIX Thumbwheel Assignments this is OptionalSelected Models Special Instructions Micro PulseGB/WSB GBM GB/WSB 240RPower OFF Power onInstructions for Normal Operation After Several Days of Proper OperationNormal Operating Sequence Each Cycle Wait 5 seconds, until display says Press Display will say Eight Character Display Strobe Light and Beeper Alarms Alarm SilenceROM OK LED LightsMixer Motor ON/OFF/TIMED Switch Mixer Motor OutletThumbwheel Switches Internal FusesKeypad Summary Description Keypad Automatic Operation Mode Keypad Description of FunctionsTotal RecipeBatch BtchBatch Count FastTAG OperatorKeypad Manual Mode Timed TimePage Keypad Program Mode FLG 1TY 2TY 3TY CTY MIX 1CS 2CS 3CS TRCPara ViewYLD Ctrl Page Explanation EepromPage Page Page Page Page Page MIX Time ParametersParameter List Brief Explanations Page Component Parameters OFF Designates Material TypePage Parameter List Full Explanations FLGJOG KDF, WDF ROV Page Page Dispense Station Configuration Tare Weight STL Do not Change TheseXTP XCV + XRCTCV + TRC CPL XALXUL MCT MPOLIQ REG = Regrind NAT = Natural ADD = Additive OFF =Not Used Page Page Page Page Page Page Parameter Default Settings Twelve Software FLG MIX JOGFCV DTI KDF WDF BER ROC ROV RHL FUL1TY = OFF 1CS 1AL 1XT 1SE 1MI 1NC 1PT 1RP 1RD1LA 1PO 3TY 3CS 3AL 3XT 3SE 3WTChanging Parameters Prnt OFF PrntFinal DISP,% Rate GR/TIMEFinal DISP,% What to Check for Page Page Page Calibrate Comp Special TestsTime Comp Material Usage Information PARAMETER, PRTDate Time Current Last PrintedPart IV Troubleshooting What to do Typical Problems Page Normal Operating Sequence Material Runs OUT Verifying Load Cell Function CNT Load Cell RAW Signal ReadoutCNT OFF Load Cell Weigh BIN Test Results to ExpectCore Dump Clear RoutineClear ALL Restart Internal MIX Motor Level SensorWeigh BIN Dump Valve MIX Problems Page Recalibration of Load Cells FullBlender Preventive Maintenance Dispense GatesLoad Cells Weigh BinsPage Computer Outputs Wiring Supplement Page Call Appendix A-2 Specifications Gravimetric Batch Blenders Autoweigh GBM Series ModelsGravimetric Batch Blenders AutoWeigh GB100 Series Models TOP View Front View Side View120V/1 phase/50-60 Hz 240V/1 phase/50-60 Hz Gravimetric Batch Blenders GB 220 and 420 ModelsGravimetric Batch Blenders AutoWeigh GB240 and GB440 Models TOP View Mounting InterfaceGravimetric Batch Blenders AutoWeigh GB900 Series Models 2124Gravimetric Batch Blenders AutoWeigh GB1840 and 1860 Models GB1840 GB1860Gravimetric Batch Blenders Wsbm Series models Control Remote Mounted Models WSBM22 WSBM131 WSBM140Gravimetric Batch Blenders WSB 100 and 100R Models Side View Front View Side View, R Model Front View, R ModelGravimetric Batch Blenders WSB 220 and 420 Models 24.4Gravimetric Batch Blenders WSB 240/440 and 240/440R Models WSB442Gravimetric Batch Blenders WSB 1840, 1850 and 1860 Models Appendix C Appendix C Appendix C Appendix C Appendix C Appendix C Appendix C Appendix C

GB, WSB specifications

The Conair WSB,GB represents a cutting-edge advancement in hair styling technology designed for both professionals and everyday users. Known for its versatility, this styling device merges high-performance with user-friendly characteristics to deliver exceptional results.

One of the standout features of the Conair WSB,GB is its dual voltage capability. This allows users to take it anywhere in the world without worrying about voltage inconsistencies, making it an ideal travel companion. The device's sleek and portable design ensures that it is easy to pack while still being robust enough to handle regular usage.

The WSB,GB incorporates advanced heating technology that ensures rapid heat-up times, allowing users to get to styling quickly. With multiple heat settings, the device caters to various hair types and styles, whether it's coarse, fine, or color-treated hair. This customization is essential for achieving the perfect look while minimizing damage.

Another impressive characteristic of the Conair WSB,GB is its innovative ceramic technology. The ceramic plates distribute heat evenly, reducing hot spots that can lead to hair damage. This feature ensures that styling is not only efficient but also gentle on the hair, promoting a healthy shine and reducing frizz for a polished finish.

The device also boasts a swivel cord, which enhances convenience during use by allowing for free movement without the hassle of tangling. This ergonomic consideration is particularly beneficial for professional hairstylists who may need to maneuver around clients during appointments.

Safety is a crucial aspect of the WSB,GB design. It includes an automatic shut-off feature that turns the device off after a period of inactivity, providing peace of mind for users who might accidentally leave it on when finished.

In summary, the Conair WSB,GB offers various features that cater to the modern user’s needs. With its dual voltage, rapid heating capabilities, ceramic technology, swivel cord, and safety features, it stands out in the crowded hair styling market. Whether you’re a professional stylist or someone looking to elevate your everyday look, the WSB,GB is engineered to meet these demands with excellence.
Top Page Image Contents