Conair WSB, GB manual Normal Operating Sequence Each Cycle, Special Features

Page 22

NORMAL OPERATING SEQUENCE - EACH CYCLE

As the sensor is uncovered, the cycle begins. The target weight of a complete batch is 18000, 9000, 4000, 2000, 1000, or 400 grams.

REGRINDS are dispensed first, in their order of size, largest dispense first. After all the Regrind dispenses, the space remaining in the weigh bin is determined.

NATURALS are dispensed second, in their order of size, each at the correct ratio to the others. These dispenses are calculated to fill the bin leaving just enough space for the Additive dispenses. After all Natural dispense are complete the exact weight of all of the NATURALS is determined and, based on this actual dispense weight, the Additive dispenses are now calculated.

ADDITIVES are dispensed last. These dispenses are calculated as a percentage of all the NATURAL components only.

If any dispense fails to reach the requested weight, the process does NOT CONTINUE. The ALARM Strobe light flashes, the Beeper sounds, and the system continues to retry the dispense until the problem is remedied.

The total batch is then dropped into the mixing chamber for blending before entering the throat of the process machine.

SPECIAL FEATURES

To use one of these SPECIAL FEATURES, read about it first. The KEYSTROKE sequence required is given at the end of this section.

To TAG all material usage data with Work Order or Employee numbers for better tracking of material used, read:

KEYPAD, TAG key, and set 2nd digit in the FLG parameter to 1.

To store RECIPES using the RECIPE storage feature, read:

KEYPAD, RECIPE key, and set 3rd digit in the FLG parameter to 1.

To increase throughput, using the FAST key, read:

KEYPAD, FAST key, and set 4th digit in the FLG parameter to 1.

To blend a preset BATCH amount of material and then stop, read: KEYPAD, BATCH key, and set 5th digit in the FLG parameter to 1.

BATCH, RECIPE, FAST, and TAG keys REQUIRE that you read: PARAMETERS, FLG parameter.

To use a lower percentage then 00.1 percent, read:

PARAMETERS, _XT parameter.

To change the MIXER RUN TIME, read:

PARAMETERS, MIX Parameter.

To place UPPER LIMITS on settings, read:

PARAMETERS, _SE Parameter.

Page 23

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Gravimetric Blenders Date Manual Number UGB007/1103 Serial numbers Model numbers Twelve Component Software Part Troubleshooting / SoftwarePart Hardware Maintenance Part OperationProceed to Safety Hazards Next Check OUT ProcedureSpecial Features Slide ValvesProceed to Assembly Next Safety Hazards MIX BladesSafety Features Safety Interlock Switch Additional MIX Blade HazardDisclaimers Part I Assembly Page Wiring Considerations Proceed to Check OUT Procedure NextAT this Point Procedure What should Happen Plug in ControllerTurn Power on Touch Weigh BIN Very LightlyALL Models Press Alarm KEYFacing the Controller Side of the Blender Press Dump KEYPage Selecting Correct Model Weigh BIN Load Cell Grams Dimensions Rating GBMPassword Model Batch WTCAL Part II Operation Load Cell CalibrationCAL OFF ZeroRegrind Percent of MIX Turning on Outputs Material TypesNatural Ratio to Each Other Natural SET= Additive Percent of ALL NaturalsRegrind On the Other HandTypes Proceed to Rate Calibration NextOper Proceed to Entering Settings NextRate Calibration YOU Dont have to do this OperateEntire MIX Other Natural SettingsSET Thumbwheel Assignments this is OptionalGB/WSB GBM Selected Models Special InstructionsMicro Pulse GB/WSB 240RInstructions for Normal Operation Power OFFPower on After Several Days of Proper OperationNormal Operating Sequence Each Cycle Wait 5 seconds, until display says Press Display will say Eight Character Display ROM OK Strobe Light and Beeper AlarmsAlarm Silence LED LightsMixer Motor ON/OFF/TIMED Switch Mixer Motor OutletThumbwheel Switches Internal FusesKeypad Summary Description Total Keypad Automatic Operation ModeKeypad Description of Functions RecipeBatch BtchBatch Count FastTAG OperatorKeypad Manual Mode Timed TimePage Keypad Program Mode Para FLG 1TY 2TY 3TY CTY MIX 1CS 2CS 3CSTRC ViewYLD Ctrl Page Explanation EepromPage Page Page Page Page Page Parameter List Brief Explanations ParametersMIX Time Page Component Parameters OFF Designates Material TypePage Parameter List Full Explanations FLGJOG KDF, WDF ROV Page Page Dispense Station Configuration Tare Weight STL Do not Change TheseTCV + TRC XCV + XRCXTP XUL XALCPL LIQ MPOMCT Not Used OFF =REG = Regrind NAT = Natural ADD = Additive Page Page Page Page Page Page FCV DTI KDF WDF BER Parameter Default Settings Twelve SoftwareFLG MIX JOG ROC ROV RHL FUL1LA 1PO 1TY = OFF 1CS 1AL 1XT 1SE1MI 1NC 1PT 1RP 1RD 3TY 3CS 3AL 3XT 3SE 3WTChanging Parameters Final DISP,% Prnt OFFPrnt Rate GR/TIMEFinal DISP,% What to Check for Page Page Page Time Comp Special TestsCalibrate Comp Date Time Current Material Usage InformationPARAMETER, PRT Last PrintedPart IV Troubleshooting What to do Typical Problems Page Normal Operating Sequence Material Runs OUT Verifying Load Cell Function CNT OFF Load Cell RAW Signal ReadoutCNT Load Cell Weigh BIN Test Results to ExpectClear ALL Restart Clear RoutineCore Dump Weigh BIN Dump Valve Level SensorInternal MIX Motor MIX Problems Page Recalibration of Load Cells FullLoad Cells Blender Preventive MaintenanceDispense Gates Weigh BinsPage Computer Outputs Wiring Supplement Page Call Appendix A-2 Specifications Gravimetric Batch Blenders Autoweigh GBM Series ModelsGravimetric Batch Blenders AutoWeigh GB100 Series Models TOP View Front View Side View120V/1 phase/50-60 Hz 240V/1 phase/50-60 Hz Gravimetric Batch Blenders GB 220 and 420 ModelsGravimetric Batch Blenders AutoWeigh GB240 and GB440 Models TOP View Mounting InterfaceGravimetric Batch Blenders AutoWeigh GB900 Series Models 2124Gravimetric Batch Blenders AutoWeigh GB1840 and 1860 Models GB1840 GB1860Gravimetric Batch Blenders Wsbm Series models Control Remote Mounted Models WSBM22 WSBM131 WSBM140Gravimetric Batch Blenders WSB 100 and 100R Models Side View Front View Side View, R Model Front View, R ModelGravimetric Batch Blenders WSB 220 and 420 Models 24.4Gravimetric Batch Blenders WSB 240/440 and 240/440R Models WSB442Gravimetric Batch Blenders WSB 1840, 1850 and 1860 Models Appendix C Appendix C Appendix C Appendix C Appendix C Appendix C Appendix C Appendix C

GB, WSB specifications

The Conair WSB,GB represents a cutting-edge advancement in hair styling technology designed for both professionals and everyday users. Known for its versatility, this styling device merges high-performance with user-friendly characteristics to deliver exceptional results.

One of the standout features of the Conair WSB,GB is its dual voltage capability. This allows users to take it anywhere in the world without worrying about voltage inconsistencies, making it an ideal travel companion. The device's sleek and portable design ensures that it is easy to pack while still being robust enough to handle regular usage.

The WSB,GB incorporates advanced heating technology that ensures rapid heat-up times, allowing users to get to styling quickly. With multiple heat settings, the device caters to various hair types and styles, whether it's coarse, fine, or color-treated hair. This customization is essential for achieving the perfect look while minimizing damage.

Another impressive characteristic of the Conair WSB,GB is its innovative ceramic technology. The ceramic plates distribute heat evenly, reducing hot spots that can lead to hair damage. This feature ensures that styling is not only efficient but also gentle on the hair, promoting a healthy shine and reducing frizz for a polished finish.

The device also boasts a swivel cord, which enhances convenience during use by allowing for free movement without the hassle of tangling. This ergonomic consideration is particularly beneficial for professional hairstylists who may need to maneuver around clients during appointments.

Safety is a crucial aspect of the WSB,GB design. It includes an automatic shut-off feature that turns the device off after a period of inactivity, providing peace of mind for users who might accidentally leave it on when finished.

In summary, the Conair WSB,GB offers various features that cater to the modern user’s needs. With its dual voltage, rapid heating capabilities, ceramic technology, swivel cord, and safety features, it stands out in the crowded hair styling market. Whether you’re a professional stylist or someone looking to elevate your everyday look, the WSB,GB is engineered to meet these demands with excellence.
Top Page Image Contents