Bunn HC-3 Auger Drive Components, If voltage is present as described, proceed to #5, Hopper Assy

Page 13

SERVICE

AUGER DRIVE COMPONENTS (cont.)

If voltage is present as described, proceed to #5.

If voltage is not present as described, refer to the wir- ing diagrams and check the dispenser wiring harness.

5.With the wires removed from the motor to be tested. Check for continuity across the two ter- minals on the bottom of the auger motor.

If continuity is present as described, reconnect the wires to the terminals on the bottom of the auger motor, the auger motor is operating properly.

If continuity is not present as described, replace the auger motor.

Removal, Cleaning and Replacement

Hopper & Auger

1.Open the dispenser door and raise the top front cover.

2.Lift the front edge of hopper assy (21) over the tab on hopper support plate (20) and slide hop- per assembly out the front of the dispenser.

3.Remove hopper lid (1) and empty product.

4.Pull off the ejector elbow (14).

5.Remove auger disc assy (2) by pulling agitator support rod (4) towards agitator disc assy and lifting agitator disc assy from hopper (10).

6.Remove auger (12) by pulling it out the front of the hopper (10).

7.Remove auger drive shaft (5) by removing the retaining clip (6) from auger drive shaft.

8.Slide washer (8) and auger drive shaft bracket

(7) off of the auger drive shaft (5).

9.Slide auger drive shaft (5) from auger drive shaft bushing (3) and remove from hopper (10).

10.Remove locknut (9) from auger drive shaft bush- ing (3) and remove auger drive shaft bushing from hopper (10).

11.Wash components in a mild solution of dish de- tergent using a bristle brush when needed.

12.Rinse and dry each item thoroughly.

13.Check for damaged or broken components, re- place any if necessary and reassemble hopper assy.

1		4
2
3	6	11
	6

5
		13
7
8		12
9		12
9		14
10		14
10
	21
15 16 17 18 19 20
		P1200.35
FIG. 2 AUGER DRIVE & HOPPER DISASSEMBLY

1.	Hopper Lid	10.	Hopper
2.	Agitator Disc Assy	11.	Spring
3.	Auger Drive Bracket	12.	Auger Wire
4.	Agitator Support Rod	13. Auger Wire/Restrictor
5.	Auger Drive Shaft		(Optional)
	Bushing	14.	Ejector Elbow
6.	Retainer Clip	15. Wiring Harness Clamp
7.	Auger Drive Bracket	16.	Auger Motor Bracket
8. Washer		17.	Auger Motor
9.	Locknut	18.	Dust Seal
		19.	Shoulder Screw
		20. Hopper Support plate
		21.	Hopper Assy

13	27591 111596

Image 13

Contents Serial # HC00025000 UP Bunn HC-2Introduction Warranty12368.0002 User Notices27620.0000 Electrical Requirements Initial SET-UPElectrical HOOK-UP Plumbing RequirementsAdjustments CleaningDispenser USE Cold Beverage SET-UP OptionalDraining the HOT Water Tank TroubleshootingHopper Dispense Rate of Product Problem Probable Cause Remedy TroubleshootingProblem Dripping from dispense tip Lime build-up Problem Probable CauseOn stainless steel surfaces can Ing in serious leaksTesting procedure. See Weak product Water temperature30 or Tip with a thermometerProbable Cause Remedy Troubleshooting ProblemComponent Access ServiceContents Auger Drive ComponentsIf voltage is present as described, proceed to #5 Auger Drive ComponentsWasher Auger Motor Locknut Dust Seal Shoulder Screw Hopper AssyRight HC-2 ServiceBallast Test ProcedureLocation Control Thermostat Remove temperature probe from the tankLocation Mechanical Thermostat Electronic Thermostat OptionalThermostat Terminals Control ThermostatDispense Switch Dispense SwitchFAN Test ProceduresSteam Collector #6-32 Screw Mixing Chamber Frother and Whipper MotorRing Pull the mixing chamber 2 out of the whipper chamberWhipper Motor Terminals Frother and Whipper MotorReconnect the eight pin connector to the hopper delay board Hopper Delay BoardDisconnect the wires from the switch termi- nals HOT/COLD Switch OptionalLamp Holder Lamp Replacement Refer to FigDoor Assy Service Level Control Board and Probe Level Control Board and Level ProbeLimit Thermostat Level Board TerminalsOverflow Protection Switch Overflow Protection SwitchRUN/RINSE Switch RUN/RINSE SwitchCold Water Solenoid Valve Solenoid Valve Cold Water OptionalSolenoid Valves Dispense Cold Water Solenoid TerminalsDisconnect the water line from the solenoid valve Solenoid Valves DispenseSolenoid Valve Inlet Tank Heater Solenoid Valve InletTank Heater Switch Refer to when reconnecting the wires to the tank heaterTank Heater Tank Heater Switch Terminals Tank Heater SwitchMODELSONLYcont Transformer 240V TWO WireSchematic Wiring Diagram HC-2, & HC-3 Schematic Wiring Diagram HCA-2, & HCA-3