Bunn Essential Guide and Warranty Information for the FMD-3 Beverage Dispenser

Page 2

INTRODUCTION

This equipment dispenses hot beverages on demand from powdered product. It has two or three hoppers. The two and three hopper models may also dispense cold beverages from powdered product from their left dispense station. It is for indoor use only on a sturdy counter or shelf.

BUNN-O-MATIC COMMERCIAL PRODUCT WARRANTY

Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows:

1)All equipment other than as specified below: 2 years parts and 1 year labor.

2)Electronic circuit and/or control boards: parts and labor for 3 years.

3)Compressors on refrigeration equipment: 5 years parts and 1 year labor.

4)Grinding burrs on coffee grinding equipment to grind coffee to meet original factory screen sieve analysis: parts and labor for 3 years or 30,000 pounds of coffee, whichever comes first.

These warranty periods run from the date of installation BUNN warrants that the equipment manufactured by it will be commercially free of defects in material and workmanship existing at the time of manufacture and appearing within the applicable warranty period. This warranty does not apply to any equipment, component or part that was not manufactured by BUNN or that, in BUNN’s judgment, has been affected by misuse, neglect, alteration, improper installation or operation, improper maintenance or repair, damage or casualty. This warranty is conditioned on the Buyer 1) giving BUNN prompt notice of any claim to be made under this warranty by telephone at (217) 529-6601 or by writing to Post Office Box 3227, Springfield, Illinois 62708-3227; 2) if requested by BUNN, shipping the defective equipment prepaid to an authorized BUNN service location; and 3) receiving prior authorization from BUNN that the defective equipment is under warranty.

THE FOREGOING WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTY, WRITTEN OR ORAL, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF EITHER MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. The agents, dealers or employees of BUNN are not authorized to make modifications to this warranty or to make additional warranties that are binding on BUNN. Accordingly, statements by such individuals, whether oral or written, do not constitute warranties and should not be relied upon.

If BUNN determines in its sole discretion that the equipment does not conform to the warranty, BUNN, at its exclusive option while the equipment is under warranty, shall either 1) provide at no charge replacement parts and/or labor (during the applicable parts and labor warranty periods specified above) to repair the defective components, provided that this repair is done by a BUNN Authorized Service Representative; or 2) shall replace the equipment or refund the purchase price for the equipment.

THE BUYER’S REMEDY AGAINST BUNN FOR THE BREACH OF ANY OBLIGATION ARISING OUT OF THE SALE OF THIS EQUIPMENT, WHETHER DERIVED FROM WARRANTY OR OTHERWISE, SHALL BE LIMITED, AT BUNN’S SOLE OPTION AS SPECIFIED HEREIN, TO REPAIR, REPLACEMENT OR REFUND.

In no event shall BUNN be liable for any other damage or loss, including, but not limited to, lost profits, lost sales, loss of use of equipment, claims of Buyer’s customers, cost of capital, cost of down time, cost of substitute equipment, facilities or services, or any other special, incidental or consequential damages.

USER NOTICES

Carefully read and follow all notices on the equipment and in this manual. They were written for your protection. All notices are to be kept in good condition. Replace any unreadable or damaged labels.

PUSH and HOLD BUTTON UNTIL CUP IS 2/3 FULL, THEN RELEASE

PUSH and HOLD BUTTON UNTIL CUP IS 2/3 FULL, THEN RELEASE

FMD-2 28301.0002

FMD-3 28301.0000

2

28364 080202

 

Image 2
Contents Post Office BOX SPRINGFIELD, Illinois Phone 217 529-6601 FAX 217BUNN-O-MATIC Commercial Product Warranty FMD-2 FMD-326536.0002 00656.0000 00831.000028368.0000 FMD-2Initial SET-UP Initial Fill & Heat Plumbing HOOK-UPDraining the HOT Water Tank Problem Probable Cause RemedyStat for testing procedures. See TroubleshootingReplacement Control thermostat Leaks Product overflows container Dispense switchDripping from dispense tip Lime build-up ColdProblem Probable Cause RemedyNoises Water Supply Tank Heater Excess dust Fan Refer to Service Lamp, see page 23 for lamp replacementDispenser is making unusual Display not lit Lamp Lamp Holder Starter Lamp BallastAuger Drive Components Component AccessContents Off of the auger drive shaft Hopper Lid Auger Wire Agitator Disc AssyIf voltage is present as described, proceed to #5 Auger Drive Shaft Optional Bushing Ejector ElbowAuger Drive Components Remove dust seal 18 from auger motorHarness BLK to BLU From Door Interconnect Refer to when reconnecting the wiresBallast Remove temperature probe from the tank Control ThermostatLocation Dispense SwitchControl Thermostat Location Dispense SwitchFAN Steam Collector Ring Mixing Chamber #8-32 Acorn Nut FANFrother and Whipper Motor Washer Ring Nut FrotherFrother and Whipper Motor Hopper Delay Board Whipper Motor Terminals P1451.40HOT/COLD Switch Optional Disconnect the wires from the switch termi- nalsDoor Assy Upper Panel Lamp Holders Lower Panel Lamp Replacement Refer to FigLamp Holder Remove the outside window and display graphicLevel Control Board and Level Probe As assemblyLamp Starter and Socket Level Control Board and Level Probe Limit Thermostat Limit ThermostatBoard Overflow Protection SwitchFrom Main Harness Rinse /RUN Switch RINSE/RUN SwitchSolenoid Valve Cold Water Optional Cold Water Solenoid ValveCold Water Solenoid Terminals Solenoid Valves DispenseSolenoid Valves Dispense Solenoid Valve InletSolenoid Valve Inlet Tank HeaterTank Heater Main Wiring Thermostat HarnessTank Heater Switch Tank Heater Switch Tank Heater Switch TerminalsSchematic Wiring Diagram FMD-1, FMD-2, & FMD-3 Schematic Wiring Diagram FMDA-1, FMDA-2, & FMDA-3