Bunn FMD-3 service manual Initial Fill & Heat, Plumbing HOOK-UP

Page 5

PLUMBING HOOK-UP

1.Securely attach the short piece of tubing on the water strainer assembly to the inlet fitting on the bottom of the dispenser.

2.Flush the water line and securely attach it to the flare fitting on the water strainer assembly.

3.Turn-on the water supply.

INITIAL FILL & HEAT

CAUTION - The dispenser must be disconnected from the power source throughout the initial fill & heat, except when specified in the instructions.

1.Turn-on the water supply and connect the dispenser to the power source.

2.Water will automatically flow into the tank to the proper level and then shut-off. This will take less than five minutes.

3.When the tank is full of water, open the front door and place the heater switch in the “ON” (lower) position. A tank full of cold water will take approximately forty minutes for the water to heat on 120 volt versions, and twenty minutes on 120/240 and 240 volt versions.

During this waiting period, complete these dispenser set-up steps:

a.Place a set of keyholes in the splash panel over the screws beneath the hopper access door and push down gently.

b.Place the drip tray onto the supports on the splash panel. Hook the tabs on the rear of the drip tray through the holes in the splash panel. Set the drip tray cover in place.

c.Fill the hopper(s) with the dry product to be dispensed.

DISPENSER USE

1.Simply place a cup on the drip tray beneath the desired dispensing tip.

2.Press the button to froth and dispense the beverage.

3.Release the button when the cup is approximately 2/3 full and allow the mixing chamber to drain.

NOTE - The mixing chamber must drain at the end of each dispense.

COLD BEVERAGE SET-UP (OPTIONAL)

Cold beverages may be dispensed from the left dispense position on the FMD-2 & FMD-3 models. Simply place the HOT/COLD switch near the left whipper chamber in the “COLD” (upper) position.

CLEANING

Refer to the decal inside the hopper access door for cleaning recommendations and procedures.

The use of a damp cloth rinsed in any mild, non-abrasive, liquid detergent is recommended for cleaning all surfaces on Bunn-O-Matic equipment.

ADJUSTMENTS

The hot or cold beverage solenoid(s) is (are) preset to dispense approximately one ounce per second. This amount can be adjusted:

1.Disconnect the dispenser from the power source.

2.Remove the small left side access panel.

3.Rotate the control at the base of the desired solenoid(s) clockwise to decrease or counterclockwise to increase the amount of water.

4.For cold beverage adjustment remove the 1-1/2” plug on the lower left side of the dispenser and rotate the needle valve clockwise to decrease or counterclockwise to increase the amount of cold water.

5

28364 011598

 

Image 5
Contents Phone 217 529-6601 FAX 217 Post Office BOX SPRINGFIELD, IllinoisFMD-2 FMD-3 BUNN-O-MATIC Commercial Product Warranty28368.0000 00656.0000 00831.000026536.0002 FMD-2Initial SET-UP Plumbing HOOK-UP Initial Fill & HeatDraining the HOT Water Tank Remedy Problem Probable CauseStat for testing procedures. See TroubleshootingReplacement Control thermostat Dripping from dispense tip Lime build-up Product overflows container Dispense switchLeaks ColdProbable Cause Remedy ProblemDispenser is making unusual Refer to Service Lamp, see page 23 for lamp replacementNoises Water Supply Tank Heater Excess dust Fan Display not lit Lamp Lamp Holder Starter Lamp BallastAuger Drive Components Component AccessContents If voltage is present as described, proceed to #5 Hopper Lid Auger Wire Agitator Disc AssyOff of the auger drive shaft Auger Drive Shaft Optional Bushing Ejector ElbowRemove dust seal 18 from auger motor Auger Drive ComponentsHarness BLK to BLU From Door Interconnect Refer to when reconnecting the wiresBallast Control Thermostat Remove temperature probe from the tankLocation Dispense SwitchControl Thermostat Location Dispense SwitchFAN Frother and Whipper Motor FANSteam Collector Ring Mixing Chamber #8-32 Acorn Nut Washer Ring Nut FrotherFrother and Whipper Motor Whipper Motor Terminals P1451.40 Hopper Delay BoardDisconnect the wires from the switch termi- nals HOT/COLD Switch OptionalLamp Holder Lamp Replacement Refer to FigDoor Assy Upper Panel Lamp Holders Lower Panel Remove the outside window and display graphicLevel Control Board and Level Probe As assemblyLamp Starter and Socket Level Control Board and Level Probe Limit Thermostat Limit ThermostatBoard Overflow Protection SwitchFrom Main Harness RINSE/RUN Switch Rinse /RUN SwitchCold Water Solenoid Valve Solenoid Valve Cold Water OptionalSolenoid Valves Dispense Cold Water Solenoid TerminalsSolenoid Valve Inlet Solenoid Valves DispenseTank Heater Solenoid Valve InletTank Heater Main Wiring Thermostat HarnessTank Heater Switch Tank Heater Switch Terminals Tank Heater SwitchSchematic Wiring Diagram FMD-1, FMD-2, & FMD-3 Schematic Wiring Diagram FMDA-1, FMDA-2, & FMDA-3